Contest Number Programming; Decrementing The Contest Number - Yaesu FT-2000 Operating Manual

C CW M
HECKING THE EMORY
1. Be sure that Break-in is still turned Off by the [ BK-IN ]
button.
2. Press the [ MONI ] button to enable the CW monitor.
3. Press the [ F1 ( CH1 )] ~ [ F4 ( CH-4 )] button to check
your work. You will hear the results in the sidetone,
but no RF energy will be transmitted.
N :
OTE
Adjust the monitor level using the [ MONI ] knob.
O -T -A CW M
N HE IR ESSAGE
1. Press the [ BK-IN ] button to enable transmission. Ei-
ther Full- or Semi-break-in will be engaged, depend-
ing on the setting of Menu item "058 A1A BK-IN
2. Press the [ F1 ( CH1 )] ~ [ F4 ( CH-4 )] button to transmit
the programmed message.
N :
OTE
If you subsequently decide to use the "Message Memory"
technique for memory storage, please note that the con-
tents of a message stored using text input will not be trans-
ferred over when you select "Message Memory technique"
on a particular memory register (the Menu Mode Setting
is set to "tyP2
tyP2 tyP2 tyP2 tyP2").

Contest Number Programming

Use this process if you are starting a contest, or if
you somehow get out of sync with the proper num-
ber in the middle of a contest.
1. Press the [ MENU ] button to enter the Menu
mode.
2. Rotate the Main Tuning Dial knob to select
Menu item "019 tEy CONTEST
019 tEy CONTEST 019 tEy CONTEST." 019 tEy CONTEST
019 tEy CONTEST
3. Rotate the [ SUB VFO-B ] knob to set the Con-
test Number to the desired value.
Advice:
Press the [ CLEAR ] button (located below and
to the left of the [ CLAR ] knob) to reset the Con-
test Number to "1 1 1 1 1 ."
4. Press and hold in the [ MENU ] button for two
seconds to store the new number and exit to
normal operation.
TEXT DISPLAY CW CODE
!
SN
"""
AF
#
---
$
SX
% % % % %
KA
&
AS
'''
WG
FT-2000 O
PERATING
CW C
C
ONTEST
C
ONTENTS
P
LAYBACK
058 A1A BK-IN 058 A1A BK-IN
058 A1A BK-IN." 058 A1A BK-IN
TEXT DISPLAY CW CODE
(
KN
")"
KK
*
---
+
AR
, , , , ,
MIM
---
DU
.
AAA
M
ANUAL
ONVENIENCE
M K
EMORY EYER
[ BK-IN ] Button
[ F1 ( CH-1 )] ~ [ F4 ( CH-4 )] Button
[ BK-IN ] Button
[ F1 ( CH-1 )] ~ [ F4 ( CH-4 )] Button

Decrementing the Contest Number

Use this process if the current contest number gets
slightly ahead of the actual number you want to
send (in case of a duplicate QSO, for example).
Press the [ F6 ( DEC )] button on the front panel. The
current Contest Number will be reduced by one.
Press the [ F6 ( DEC )] button as many times as nec-
essary to reach the desired number. If you go too
far, use the "Contest Number Programming" tech-
nique desired above.
TEXT DISPLAY CW CODE
/ / / / /
":"
;
<
= = = = =
>
?
F
EATURES
TEXT DISPLAY CW CODE
@ @ @ @ @
DN
"["
OS
\ \ \ \ \
KR
]
---
^ ^ ^ ^ ^
BT
_ _ _ _ _
---
'}'
IMI
Page 87
@
---
AL
---
---
IQ
---