Advertisement
Quick Links
Advertisement
Related Manuals for Milnor 30022H8J
Summary of Contents for Milnor 30022H8J
- Page 1 Published Manual Number/ECN: MAI30H7XAE/2003062N • Publishing System: TPAS • Access date: 2/3/2003 • Document ECN's: Latest Available Installation— 30022H8J Washer-Extractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
- Page 2 “Troubleshooting” chapter or section. See the table of contents. Trademarks of Pellerin Milnor Corporation The following, some of which may be used in this manual, are trademarks of Pellerin Milnor Corporation: ®...
-
Page 3: Table Of Contents
Table of Contents for MAI30H7XAE/2003062N 30022H8J Washer-Extractors Page Description Document/ECN About the Forces Transmitted by Milnor Washer-Extractors BIWUUI02/20001108 Avoiding Damage From Allied Remote Chemical Delivery Systems BIWUUI03/20030129 Section 1: Installation Handling and Setting Procedures for 30022H7J and 30022H8J Washer-Extractors MSIN0705AE/2000266V... -
Page 5: About The Forces Transmitted By Milnor Washer-Extractors
• the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model ® and size upon request. Floor or foundation sizes shown on any Milnor... - Page 6 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain ® written confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
-
Page 7: Avoiding Damage From Allied Remote Chemical Delivery Systems
® of such systems by the chemical supply company. Milnor washer-extractors and CBW batch washers (tunnels) are available with convenient inlets for such systems (see Figure 1). Most common of the types of systems currently used in commercial laundering operations are pumped chemical systems. -
Page 8: Delivery Systems
CAUTION 1 : Equipment and Textile Damage Hazards—Chemicals leaked into the machine, particularly when it is idle can destroy machine components and textiles left in the machine. Pellerin Milnor Corporation accepts absolutely no responsibility for damage to its equipment or to textiles therein from abnormal contact with chemicals. - Page 9 Hence, any concentrated chemical that remains in the injection line between the pump and the machine is free to flow into the machine. Some examples of this are shown in Figure 3. PELLERIN MILNOR CORPORATION...
-
Page 10: Delivery Systems
PELLERIN MILNOR CORPORATION... -
Page 11: Pellerin Milnor Corporation
CAUTION 2 : Injury and Damage Hazards—Chemicals leaking from a chemical system may be corrosive or toxic. Such chemicals can injure personnel and damage equipment. • Use care when connecting chemical lines. • Inspect regularly for leaks. — End of BIWUUI03 — PELLERIN MILNOR CORPORATION... -
Page 13: Section 1: Installation
Section Installation... -
Page 14: Handling And Setting Procedures For 30022H7J And 30022H8J Washer-Extractors
MSIN0705AE/2000266V È H ANDLING AND SETTING PROCEDURES FOR 30022H7J AND 30022H8J WASHER-EXTRACTORS Ê H andling Precautions 1. Remove the protective coverings (leaving the machine on shipping skids) and carefully examine for possible shipping damage. If the machine is damaged, notify the transportation company immediately. - Page 15 If another bolt installation procedure is ® used, do not install the bolts until the machine is on site and bolt locations can be determined. Consult Milnor if any obstruction prevents the installation of any anchor bolt. Anchor bolts cannot be indiscriminately omitted.
- Page 16 Do not tighten the anchor bolt fasteners until grout is cured (see warning below). Î F IGURE 1 (MSIN0703BE) Î I dentifying Front Cross brace Î F IGURE 2 (MSIN0703BE) Î 3 0022H7J and 30022H8J Temporary Blocking Points...
- Page 17 MACHINE DAMAGE AND MALFUNCTION HAZARDS—Tightening anchor bolt fasteners onto spacers (without grout or with improperly applied grout) twists the machine frame and causes cylinder misalignment. Never tighten anchor bolt fasteners before grouting. Grout must displace total clearance between base plate and existing foundation floor. Voids must not exist! 3.
- Page 18 CUbfYSU 3_^^USdY_^c 29BAF9 ! @eR\YcXUT 2__[ c`USc 4QdUc* " " )!! " " )!! " " )!! <Q^W* 5>7 ! 1``\YS* B8# BTaeXRT2^]]TRcX^]b 6T]TaP[ Required service connections, (depending on machine model and optional features) are as follows: 1. Piped inlets and outlets (cold water, hot water, flush water, third water, direct steam, compressed air, liquid supply, and drain to sewer).
- Page 19 CUbfYSU 3_^^USdY_^c Table 2: Outlets Connection Description Destination Requirements or Description Piping Specifications Drain 3" pipe socket joint, unrestricted gravity feed Rubber hose, PVC or other to sewer (external back pressure may extend approved material per wash times - Do not reduce) plumbing code ?^fTa2^]]TRcX^]bP]S?aTRPdcX^]b F0A=8=6 "...
- Page 20 CUbfYSU 3_^^USdY_^c Figure 1: Correct Rotation During Figure 2: Line Voltage Switch Set for 240 Volt Drain and Extract (when viewing Operation front of machine) AT\^eTBWX__X]VATbcaPX]cb Remove all shipping restraints (usually marked in red). Restraints may be located behind access panels.
- Page 21 CUbfYSU 3_^^USdY_^c 2WTRZ2h[X]STaBdaUPRT & Check the perforated cylinder for smoothness. Milnor will not accept responsibility for the cylinder finish after the machine is placed in service. — End of BIRQVI01 — @5<<5B9> =9<>?B 3?B@?B1D9?>...
-
Page 23: Section 2: Dimensional Drawings
Section Dimensional Drawings...