Advertisement
Quick Links
Published Manual Number/ECN: MAI30VXXAE/2002044N
• Publishing System: TPAS
• Access date: 01/30/2002
• Document ECN's: Latest Available
Installation—
30015, 30022 Cxx, Vxx,Txx
Rigid Mount
Washer-Extractors
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
Advertisement
Related Manuals for Milnor C Series
Summary of Contents for Milnor C Series
- Page 1 Published Manual Number/ECN: MAI30VXXAE/2002044N • Publishing System: TPAS • Access date: 01/30/2002 • Document ECN's: Latest Available Installation— 30015, 30022 Cxx, Vxx,Txx Rigid Mount Washer-Extractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
- Page 2 “Troubleshooting” chapter or section. See the table of contents. Trademarks of Pellerin Milnor Corporation The following, some of which may be used in this manual, are trademarks of Pellerin Milnor Corporation: ®...
- Page 3 Warranty BMP720097/92732A How to Order Parts BMP720097R/72332A Rigid Mount Washer-Extractor Installation & Service Safety MSIN0704AE/9271BV About the Forces Transmitted by Milnor Washer-Extractors BIWUUI02/20001108 Glossary of Tag Illustrations - M-Style, 30" T- Style, & 30" V-Style Washer-Extractors MSIUUMTGAE/2001134V Section 1: Installation Handling and Setting Procedures for Rigid Mount 30015 &...
- Page 5 (including purchased components) without obligation to change any equipment previously supplied. ANY SALE OR FURNISHING OF ANY EQUIPMENT BY MILNOR IS MADE ONLY UPON THE EXPRESS UNDERSTANDING THAT MILNOR MAKES NO EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE.
- Page 7 How to order repair parts Repair parts may be ordered either from the authorized dealer who sold you this machine, or directly from the MILNOR factory. In most cases, your dealer will have these parts in stock. When ordering parts, please be sure to give us the following information: 1.
- Page 8 (owner/user) is responsible for understanding and ensuring the proper operation and maintenance of the machine. The owner/user must familiarize himself with the contents of all machine instruc- ® tion manuals. The owner/user should direct any questions about these instructions to a Milnor dealer or the Mil- ®...
- Page 9 Ê H azards During Assembly ELECTROCUTION HAZARD—Contact with high voltage can kill or seriously in- jure you. All electrical connections must be made by a competent electrician. Ê H azards During Servicing and Maintenance ELECTROCUTION HAZARD—High voltage is present inside electric boxes, mo- tors and many other components.
- Page 10 Ê H azards Requiring Immediate Service MULTIPLE HAZARDS—Failure to maintain machine in proper working order can result in fatal or serious injury to operators and/or damage to property. DO NOT permit operation under any of the following circumstances: Malfunctioning door interlock mechanism. Malfunctioning limit switches.
- Page 11 • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model ® and size upon request. Floor or foundation sizes shown on any Milnor...
- Page 12 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain ® written confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
- Page 13 7\_ccQbi_VDQW9\\ecdbQdY_^c± <B8DD<C604 ! "#E = Cdi\U # D Cdi\U # F Cdi\U GQcXUb 5hdbQSd_bc Illustration Explanation Stop! Read the manual first for complete instructions before continuing. Do not jack the machine here. Do not lift the machine here. Use three point or four point lifting as determined by the lifting eyes furnished. Rig the load using lifting cables of sufficient size and length to en sure cables are not over-stressed.
- Page 14 Illustration Explanation Do not start this machine until the packing materials, lifting brackets, etc. with this tag attached or behind this panel are removed. These materials are painted red. Safety stands or brackets (also painted red) may be provided with this machine. Do not discard safety stands or brackets This motor or pump should rotate in the direction of the arrow.
- Page 15 7\_ccQbi _V DQW 9\\ecdbQdY_^c± = Cdi\U # D Cdi\U # F Cdi\U GQcXUb 5hdbQSd_bc Illustration Explanation Install the appropriate part here before operating the machine. During drain and extract, the cylinder must rotate counterclockwise when viewed from here. Make cold water connection here. Make hot water connection here.
- Page 16 =C9EE=D715 " !!#$F " " Illustration Explanation Make third (reuse) water connection here. Make flushing water connection here. Do not strike shell front of washer-extractors during fork lifting. Striking shell front will cause door to leak.
- Page 17 Section Installation...
- Page 18 Do not hesitate to file a claim with the carrier if the machine is damaged in any way ® during shipment. Milnor will be glad to assist you in filing your claim, but is not responsible for any shipping damage to the machine once it has been delivered to the carrier in good condition.
- Page 19 If another bolt installation procedure is ® used, do not install the bolts until the machine is on site and bolt locations can be determined. Consult Milnor if any obstruction prevents the installation of any anchor bolt. Anchor bolts cannot be indiscriminately omitted.
- Page 20 Ê S etting Procedures See FIGURE 1 during the following procedures: 1. With the machine near the final location, unbolt the shipping skids. Observing all precautions, lift the machine off its skids and lower the machine onto temporary blockings as shown in FIGURE 1.
- Page 21 3. After determining the final position of the machine, apply grout between the existing foundation floor and base plates, while observing the following considerations: • All machines are designed to be grouted under the full area of all base plates. Grout prevents the anchor bolts from distorting the frame when the fasteners are tightened.
- Page 22 CUbfYSU 3_^^USdY_^c 29BAF9 ! @eR\YcXUT 2__[ c`USc 4QdUc* " " !"% " " !"% " " !"% <Q^W* 5>7 ! 1``\YS* B=F B=3 BTaeXRT2^]]TRcX^]b 6T]TaP[ Required service connections, (depending on machine model and optional features) are as follows: 1.
- Page 23 CUbfYSU 3_^^USdY_^c Table 2: Outlets Connection Description Destination Requirements or Description Piping Specifications Drain 3" pipe socket joint, unrestricted gravity feed Rubber hose, PVC or other to sewer (external back pressure may extend approved material per wash times - Do not reduce) plumbing code Suds Overflow (if so 2"...
- Page 24 CUbfYSU 3_^^USdY_^c Figure 1: Correct Rotation During Figure 2: Line Voltage Switch Set for 240 Volt Drain and Extract (when viewing Operation front of machine) AT\^eTBWX__X]VATbcaPX]cb Remove all shipping restraints (usually marked in red). Restraints may be located behind access panels.
- Page 25 CUbfYSU 3_^^USdY_^c 2WTRZ2h[X]STaBdaUPRT & Check the perforated cylinder for smoothness. Milnor will not accept responsibility for the cylinder finish after the machine is placed in service. >_cX^]P[;X]cCaP_ Figure 4: Lint Trap SA 02 069 Trap mounting method Legend Washer-extractor drain...
- Page 27 Section Dimensional Drawings...