Superior DRT6340TYN Installation And Operation Instructions Manual page 36

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT6340/45TYN) • INSTALLATION INSTRUCTIONS
Manifold (Out)
Test Port
Line (In) Test Port
Wire (from DFC
wire harness)
Figure 47 - SIT Electronic Gas Valve
Remote Control System
The remote control and receiver allow you to
command the functions of your fireplace from
the comfort of your chair. They are configured to
control the primary burner operation, its flame
levels (through six levels) and provide ON/OFF
and smart control of this appliance.
The control board connects directly to the gas
valve and stepper motor (see Wire Diagram
on Page 45).
The control is powered by four (4) AA batteries in the
wall switch and/or 120 VAC line power.
The control accepts commands via radio
frequency from the transmitter and does not
require line-of-sight operation.
The ON/REMOTE/OFF switch can be set to one
of three positions:
• ON (manual override)
• REMOTE (remote control)
• OFF
Initializing the System for the First Time
Install four (4) AA batteries into the receiver
battery bay, behind the wall switch plate.
NOTE: Install the batteries into the battery bay
as indicated on the battery cover. Ensure that
batteries are installed with proper polarity
(+/-).
Place the ON/REMOTE/OFF switch in the
REMOTE position (see Figure 48 on Page
37). Insert the end of the paper clip (or other
similar object) into the hole marked "PRG" on
the receiver front cover. The control board,
located in the fireplace, will "beep" three (3)
times to indicate that it is ready to synchronize
with a transmitter.
36
Green Wire
(from DFC
wire harness)
Install three (3) AAA batteries in the transmitter
battery bay, located on the base of the
transmitter. With the batteries installed in the
transmitter, push the ON button. The receiver will
"beep" four (4) times to indicate the transmitter
command has been accepted and is set to the
particular code of that transmitter. The system
is now initialized.
Low Battery Power Detection
The life span of the receiver batteries depends
on various factors:
• Quality of the batteries used
• Number of ignitions of the appliance
• etc.
When the receiver batteries are low, no "beep"
will be emitted from the receiver when it receives
an ON/OFF command from the transmitter. This
is an alert for a low battery condition for the
receiver. When the batteries are replaced the
"beep" will be emitted from the receiver when
the ON/OFF key is pressed (See Initializing the
System for the First Time).
When the transmitter batteries are low, a
battery icon will appear on the LCD display of
the transmitter before all battery power is lost.
When the batteries are replaced this icon will
disappear.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Connect GTMS
Wire Harness
Pressure
Regulator
Tower
Yellow Ground Wire
(from DFC wire
harness)
WARNING
Fire Hazard. Can cause severe
injury or death. The receiver
causes ignition of the appli-
ance. The appliance can turn on
suddenly. Keep away from the
appliance burner when operating
the remote system or activating
manual bypass of the remote
system.
CAUTION: Property damage hazard. Exces-
sive heat can cause property damage. The
appliance can stay lit for many hours. Turn
off the appliance if it is not going to be at-
tended for any length of time. Always place
the Transmitter where children can not reach
it. Control will automatically shut off after 24
hrs of continued operation
Temperature Indicator Display
With the system in the OFF position, press the
Room Temperature Key and the Mode Key at
the same time (see Figure 49 on Page 37).
Look at the LCD screen on the transmitter to
verify that a "C" or "F" is visible to the right of
the Room Temperature display (see Figure 50
on Page 37).
Turn ON the Appliance
With the receiver switch in the REMOTE position,
press the ON/OFF Key on the transmitter. The
transmitter display will show all active icons
on the screen. At the same time, the receiver
connects to the gas valve coil and the appliance
main burner turns on. A single "beep" from the
receiver will confirm reception of the command.
Turn OFF the Appliance
Press the ON/OFF Key on the transmitter. The
transmitter LCD display will only show the room
temperature and icon. At the same time, the
receiver disconnects the gas valve coil and the
appliance burner turns off. A single "beep" from
the receiver confirms reception of the command.
Remote Flame Control
The system has six (6) flame levels. See Figure
51 on Page 37 for an example. With the system
on, and the flame level at the maximum in the
appliance, pressing the Down Arrow Key once
will reduce the flame height by one step until
the flame is turned OFF.
The Up Arrow key will increase the flame height
each time it is pressed. If the Up Arrow key is
pressed while the system is ON but the flame is
OFF, the flame will come on in the high position
(see Figure 52 on Page 37). A single "beep will
confirm reception of the command.