Superior DRC6340TEP Installation And Operation Instructions Manual

Direct vent gas fireplaces

Advertisement

Quick Links

P/N 900343-01 Rev. C 11/2015
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900343-03
P900343-01
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future
reference.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit
is used.
Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements
locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque
signalétique. Cet appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neigh-
bor's phone. Follow the gas supplier's instruc-
tions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Installation and Operation Instructions
DRT/DRC6300 Series 40 and 45 in. Direct Vent
Gas Fireplaces
Models
PFS
®
C
US
Report No. F14-106
Installateur : Laissez cette notice avec l'appareil.
Consommateur : Conservez cette notice pour
consultation ultérieure.
DRT6345TEN
DRT6345TEP
DRC6345TEN
DRC6345TEP
AVERTISSEMENT:
RISQUED'INDENDIE OU D'EXPLOSION
Le non-respect Des avertissements de sécurité
pourrait d'entraîner des blessures graves, la mort
ou des dommages matériels.
- Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où
vous trouvez.
• Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par
un installateur ou un service d'entretien qualifié
ou par le fournisseur de gaz.
DRT6340TEN
DRT6340TEP
DRC6340TEN
DRC6340TEP

Advertisement

Table of Contents
loading

Summary of Contents for Superior DRC6340TEP

  • Page 1 Numéro de la pièce 900343-03 DRT6345TEP DRT6340TEP Report No. F14-106 DRC6345TEN DRC6340TEN DRC6345TEP DRC6340TEP P900343-01 INSTALLER: Leave this manual with the appliance. Installateur : Laissez cette notice avec l’appareil. CONSUMER: Retain this manual for future Consommateur : Conservez cette notice pour reference.
  • Page 2 Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 SAFETY AND YOUR FIREPLACE See attached color flyer for proper color representation DANGER HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. A barrier designed to reduce the risk of burns from the hot viewing glass is pro- vided with this appliance and shall be installed for the protection of children and other at-risk individuals.
  • Page 3 Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 La sécurité et Safety and Your Seguridad y su votre foyer Fireplace chimenea All parts of your ¡Todas las partes de la Toutes les parties de votre IHP fireplace get chimenea IHP se ponen foyer IHP deviennent EXTRÊMEMENT CHAUDES !
  • Page 4: Table Of Contents

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 TABLE OF CONTENTS Please read and understand these INTRODUCTION instructions before beginning your The DRT/DRC6300 Series direct-vent, sealed- Packaging ......4 installation.
  • Page 5: General Information

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 GENERAL INFORMATION Installation and repair should be done by WARNING a qualified service person. The appliance should be inspected before use and at least WARNING Improper installation, adjust- annually by a professional service person.
  • Page 6: Massachusetts Requirements

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Orifice Sizes—Sea Level To High Altitude In Canada - CAN/CGA-2.17-M91 (R2009) These electronic appliances are remotely (All Models) controlled and feature an electronic intermit- (high altitude): tent pilot ignition system or standing pilot. These appliances are tested and approved External electrical power is required to operate THE CONVERSION SHALL BE CARRIED...
  • Page 7: Cold Climate Insulation

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 • A metal or plastic identification plate must be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade and be directly in line with the horizontal termination.
  • Page 8: Vent Termination Clearances

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 VENT TERMINATION CLEARANCES These instructions should be used as a Vertical Vent Termination Clearances Termination Heights For Vents guideline and do not supersede local codes Above Flat Or Sloped Roofs in any way.
  • Page 9 Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 NOTE: Exterior Wall • Local codes or regulations may require different clearances. • Location of vent termination must NOT = Vent terminal 36" interfere with access to electrical service. = Area terminal NOT permitted (91.4 cm) Center Line of...
  • Page 10: Minimum Clearances To Combustibles

    Innovative Hearth Products General Information DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 MINIMUM CLEARANCES TO COMBUSTIBLES Combustible Shelf Height— Inches (millimeters) The appliance is approved with zero clearance to combustible materials on all sides (as detailed in Table 5), with the following exception: When Top Vent—with 2 Feet Vertical Vent and One 90 Degree Elbow the unit is installed with one side flush with a wall, the wall on the Model...
  • Page 11: Detailed Installation Steps

    Step 1. FRAMING TYPICAL INSTALLATION SEQUENCE WARNING Frame these appliances as illustrated in Figure The typical sequence of installation is outlined Failure to position the parts in 11 on Page 12, unless the appliance is to be below. However, each installation is unique and installed in a corner.
  • Page 12: Fireplace And Framing Specifications

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Framing should be constructed VENT FRAMING of 2x4 or larger lumber. Framing Dimensions TOP VENT WITH 2 FEET Framing should be constructed VERTICAL VENT AND Model VENT FRAMING of 2x4 or larger lumber. ONE 90°...
  • Page 13: Step 2. Routing Gas Line

    Model 50-5/8 83-5/8 59-1/8 41-7/8 40 in. 1286 2124 1502 1064 56-3/4 89-7/8 63-1/2 44-7/8 45 in. 1441 2283 1613 1140 Back wall of chase/enclosure (including any finishing materials) Figure 12—Corner Framing with Square Termination (SV8HTS) NOTES: Step 2. ROUTING GAS LINE Never use galvanized or plastic pipe.
  • Page 14: Step 3. Install The Vent System

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Step 3. INSTALL THE VENT SYSTEM Select Venting System—Horizontal or Vertical Installation of Vent Restrictor A vent restrictor may be needed with this General Information With the appliance secured in framing, de- appliance.
  • Page 15: Vertical Termination Systems

    VERTICAL TERMINATION SYSTEMS (ROOF) i t c i t c See Figure 15 and Figures 23 through 25 on i t c i t c Page 18 and their associated Vertical Vent o i t Tables which illustrate the various vertical venting configurations that are possible for use with these appliances.
  • Page 16 Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Vertical (Offset) Installation B. Attach vent components to appliance—Se- Push the vent component against the previous cure Vent SV8 direct-vent system components section until it fully engages, then twist the ®...
  • Page 17 One method of support is by utilizing field pro- K. Install the vertical termination—The final vided support straps (conventional plumber's step involves installation of the Vertical Termina- tape). Secure the plumber's tape to the framing tion. Extend the vent sections to the height as members with nails or screws.
  • Page 18: Vertical Vent Tables And Figures

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 VERTICAL VENT FIGURES/TABLES Table A NOTES: • Secure Vent (rigid vent pipe) is shown in ® V Minimum H Maximum the figures. feet (meter) feet (meter) • It is very important that the horizontal/ inclined run be maintained in a straight (3.1) (0.762)
  • Page 19: Horizontal Termination System

    HORIZONTAL (OUTSIDE WALL) TERMINATION Support Horizontal / Inclined Run SV8HTS SYSTEM Building Brackets Termination Support Shown Framing See Figures 26–31 and their associated Horizontal Vent tables that illustrate the vari- SV8E90 Elbow ous horizontal venting configurations that are possible for use with these appliances. Secure Vent pipe applications are shown in these ®...
  • Page 20 Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 J. Assemble vent run to exterior wall—If not To help minimize water infiltration it SV8HTS previously measured, locate the center of the is recommended that the Firestop/ Termination To help minimize water infiltration vent at the exterior wall.
  • Page 21: Horizontal Vent Tables And Figures

    HORIZONTAL VENT FIGURES/TABLES See Table 9 as an aid in venting component selection for a particular range of exterior wall thicknesses. NOTES: Venting Components Required for Various Exterior • Secure Vent components (rigid vent pipe and terminal) are shown ® Wall Thicknesses, when using Square Termination Kit in the figures.
  • Page 22 Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 HORIZONTAL VENT FIGURES/TABLES (continued) Wall Firestop/Spacer Table D (SV8HF) V Minimum Maximum feet (meter) feet (meter) (1.07) (0.762) (1.98) (1.07) (2.6) (1.37) 10.5 (3.2) (1.68) 12.5 (3.8) (1.98) Wall Firestop/Spacer 14.5 (4.4) (2.3)
  • Page 23: Step 4. Field Wiring

    Step 4. FIELD WIRING Verify proper operation after servicing. 6. Install the wall-mounted ON/OFF control, as described in "Installing and initializing the S’assurer que l’appareil fonctionne Remote Control System" on Page 24, in a adéquatement une fois l’entretien CAUTION convenient location near the fireplace. terminé.
  • Page 24 Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 The remote control system provides remote Installing and initializing the Remote WARNING operation of the following fireplace functions: Control System • Primary burner ON/OFF Fire hazard. Can cause severe REQUIRED ITEMS (not provided): •...
  • Page 25: Step 5. Removing Glass Door Frame Assembly

    Step 5. REMOVE GLASS DOOR FRAME A. Light the appliance (refer to the lighting instructions label in the control compartment Right Side Remove the glass door assembly. See Installa- or in the Care and Operation Instructions Modesty Panel tion and Removal of Glass Door on Page 28. manual).
  • Page 26: Step 8. Installing Logs And Panels

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Step 8. INSTALL VOLCANIC STONE, GLOWING EMBERS, AND Step 4. Position the individual logs as shown in Figures 42 through 46. Logs should be placed in the order shown. Place logs 2 and 3 LOGS (Traditional Only), or against the pins on the grate, NOT over them.
  • Page 27 Traditional Only: Log Placement Engage Logs (3 & 4) With The Grate Pins And Align Groves At The Bottom Of The Logs Over The Grate. Figure 44 - Placing Logs 3 and 4 Log Number Description Log, Center Align Hole At Bottom Of Log (5) Log, Rear Over The Pin On Log (2).
  • Page 28: Step 9. Installing Glass Door

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Step 9. INSTALLATION AND REMOVAL Installing Glass Enclosure Panel Top Flange Glass door (see Figure 47) Glass Door Latch (2) OF GLASS DOOR assembly Retrieve the glass door. Visually inspect the WARNING gasket on the backside of the frame.
  • Page 29 Air Shutter Adjustment Guidelines Use the remote to adjust the flame height as desired. • If there is smoke or soot present, first check Air Shutter Propane models may exhibit a flame pattern the log set positioning to ensure that the Opening that may candle or appear stringy.
  • Page 30: Finishing Requirements

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 FINISHING REQUIREMENTS Non-combustible materials, such as surrounds and other appliance trim, may be installed on the appliance front face with the exceptions. Wall Details Vertical installation clearances to combustible mantels vary according Complete finished interior wall.
  • Page 31: Step 11. Attaching Safety-In-Operation Warnings

    Step 11. INSTALLER INSTRUCTIONS—ATTACHING SAFETY-IN-OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance. ATTACHING SAFETY IN OPERATION WARNINGS APPOSITION DES MISES EN GARDE RELATIVES COLOCACIÓN DE ADVERTENCIAS DE SEGURIDAD It is required that the set of safety instruction labels...
  • Page 32: Installation Accessories

    Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 INSTALLATION ACCESSORIES Listed Secure Vent Components H2262 SV8SU Support Strap ® Cat. Model Description H2266 SV8HTS Horizontal Square Termination with Firestop/Spacer H2263 SV8SP Support Plate (H2260) and Adaptor (H2267) H3908 SV8ARSA Attic Insulation...
  • Page 33: Gas Conversion Kits

    GAS CONVERSION KITS Step 1. TURN OFF THE GAS SUPPLY TO THE APPLIANCE and disconnect power supply at the circuit breaker. Ensure appliance is cold. WARNING CAUTION: THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE This conversion kit shall be installed by a qualified service agency in ELECTRICAL POWER, BEFORE PROCEEDING accordance with the manufacturer’s instructions and all applicable codes WITH THE CONVERSION.
  • Page 34 Innovative Hearth Products Installation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Step 6. Refer to the instructions provided Burner Orifice Sizes with the SIT regulator conversion kit. Using a Elevation 0–4500 ft ( 0–1372 m) Pilot Torx T20 (with 1/4" shank and center hole) or Hood Nat.Gas Propane...
  • Page 35: Operation And Care Of Your Appliance

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 IMPORTANT SAFETY INFORMATION Important Safety Informa- Información importante de L’information de sûreté tion seguridad importante 1. WARNING: Do not operate appliance 1. AVERTISSEMENT. Ne pas utiliser l’appareil 1. ADVERTENCIA: No opere el artefacto con el with the glass front removed, cracked si le panneau frontal en verre n’est pas en frente de vidrio quitado, agrietado o roto.
  • Page 36 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 HOMEOWNER’S INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS APPOSITION DES MISES EN GARDE RELATIVES À COLOCACIÓN DE ADVERTENCIAS DE SEGURIDAD ATTACHING SAFETY IN OPERATION WARN- LA SÉCURITÉ D’UTILISATION EN OPERACIÓN INGS Votre foyer a été...
  • Page 37 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 APPLIANCE INSTALLATION, SERVICE, If the barrier becomes damaged, the ATTENTION : L’appareil est chaud barrier shall be replaced with the lorsqu’il fonctionne. Ne pas toucher AND MAINTENANCE NOTICES manufacturer’s barrier for this appliance. l’appareil.
  • Page 38 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 BTU INPUT In Canada—CAN/CGA-2.17-M91 (R2009) The appliance and its appliance main gas (high altitude): valve must be disconnected from the gas The BTU Input for these appliances are shown supply piping system during any pressure THE CONVERSION SHALL BE CARRIED in Table 12.
  • Page 39 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 OPERATION AND CARE OF YOUR APPLIANCE Right Side WARNING Modesty Panel Access Plate Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns.
  • Page 40: Maintenance

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 MAINTENANCE The viewing glass should be cleaned periodi- NOTE: If installing the Contemporary Burner/ Floor Kit, skip this step and instead refer to the cally to remove any build-up caused from the (See Maintenance Schedule, Page 51) following: instructions provided with the kit.
  • Page 41: Front Glass Enclosure Panel, Removal And Installation

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 FRONT GLASS ENCLOSURE PANEL, 3. Swing the door up and back. Ensure the WARNING REMOVAL AND INSTALLATION gasket seats evenly as the door draws shut. Engage the nut insert and fasten with two Any safety screen or guard screws to secure the door.
  • Page 42: Log, Volcanic Stone, And Glowing Ember Placement

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 INSTALL VOLCANIC STONE, GLOWING EMBERS, AND 4. Position the individual logs as shown in Figure 7 through Figure 11 LOGS (TRADITIONAL ONLY), OR on Page 11. Logs should be placed in the order shown. Place logs 2 GLASS MEDIA (CONTEMPORARY ONLY) and 3 against the pins on the grate, NOT over them.
  • Page 43 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Traditional Only: Log Placement Engage Logs (3 & 4) With The Grate Pins And Align Groves At The Bottom Of The Logs Over The Grate. Figure 68 - Placing Logs 3 and 4 Log Number Description Log, Center...
  • Page 44: Burner Adjustments

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 BURNER ADJUSTMENTS Contemporary Media Shown (QUALIFIED TECHNICIANS ONLY) Flame Appearance and Sooting Proper flame appearance is a flame which is blue at the base and becomes yellowish-orange in the body of the flame. When the appliance is first lit, the entire flame may be blue and will gradually turn yellowish- orange during the first 15 minutes of operation.
  • Page 45: Burner Air Shutter Adjustment

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 BURNER FLAME ADJUSTMENTS Electronic Appliance Checkout (QUALIFIED TECHNICIANS ONLY) Air Shutter To light the burner, turn on the remote control. Opening Ensure the igniter lights the pilot. The pilot WARNING flame should engulf the flame rod as shown in Figure 74.
  • Page 46: Ordering Replacement Parts

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 ORDERING REPLACEMENT PARTS When ordering repair parts always provide: PRODUCT REFERENCE INFORMATION 1. The model number of the appliance. A complete parts list is found at the end of We recommend that you record the important 2.
  • Page 47: Accessory Components

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 ACCESSORY COMPONENTS Touch-Up Paint Kit Firebox Liner Kits Repair of minor scratches and discoloration of the Bag of Glowing Embers appliances black painted surfaces may be accom- Choose from ceramic brick or porcelain panels. Bag of Volcanic Stone plished with the touch-up paint kit.
  • Page 48 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Classic Screen Kits Dual Arch Screen Kits Mission These Dual Arch screen kits can be placed in front These Classic Screen kits can be placed in front of the of the glass enclosure panel to help prevent direct glass enclosure panel to help prevent direct human human contact with the hot glass surface.
  • Page 49: Lighting Instructions

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. •...
  • Page 50 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 POUR PLUS DE SÉCURITÉ LIRE AVANT DE METTRE EN MARCHE AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort. •...
  • Page 51: Maintenance Schedule

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 MAINTENANCE SCHEDULE Turn off gas and electrical power to the fireplace and allow it to cool before cleaning or servicing the appliance. Annually (Before the onset of the Burning Season) MAINTENANCE TASK ACCOMPLISHING PERSON PROCEDURE...
  • Page 52: Troubleshooting Guide

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 TROUBLESHOOTING GUIDE NOTE: Before troubleshooting, be sure that the appliance main line gas shut-off valve and the wall switch are in the “ON” position. The following troubleshoots the fireplace only to an elementary level. For detailed Remote and Ignition System troubleshooting, refer to the instructions provided with the remote.
  • Page 53: Replacement Parts List

    Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 REPLACEMENT PARTS LIST 40 in. 45 in. Gas Controls—SIT Electronic Item Description Cat. No. Qty. Cat. No. Qty. Natural Gas Propane Gas Item Description Door Modesty Shield H4808 H4809 Part Qty.
  • Page 54 Innovative Hearth Products Operation DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 REPLACEMENT PARTS NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE...
  • Page 55: Warranty

    ® 20 Year Limited Warranty THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior Brand gas fi replace, Stove or Insert ("Product") to be free from defects in materials ® and workmanship at the time of manufacture. The Product body and fi rebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only.
  • Page 56 Innovative Hearth Products Installation and Operation Instructions DRT/DRC6300 Series Direct-Vent Gas Fireplaces 900343-01 11/2015 Contact an IHP dealer to obtain any of these parts. Please contact IHP for the phone number of your nearest IHP dealer. SuperiorFireplaces.us.com Record the following important information about your fireplace: Fireplace model number Fireplace serial number Date fireplace was Installed...

Table of Contents