Related Manuals for Siemens SIMATIC HMI IPC477C
Summary of Contents for Siemens SIMATIC HMI IPC477C
- Page 1 Compact Operating ___________________ SIMATIC HMI IPC477C / HMI IPC477C Instructions SIMATIC Industrial PC SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions 10/2010 A5E02368072-02...
- Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 3: Table Of Contents
1.9.6.1 Activating KeyTools ........................29 1.9.7 Device with touch screen ......................30 1.9.7.1 Recalibrating the Touch Screen....................30 1.9.7.2 Activating the Screen Keyboard ....................33 1.10 Service and support ........................34 Index................................ 35 SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 4 Table of contents SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 5: Compact Operating Instructions
5. Please keep the enclosed documentation in a safe place. You will need the documentation when you start up the device for the first time. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 6: Components Of The Product
Permissible number Permanently bright and permanently dark pixels ≤ 12 Permanently bright, green pixels ≤ 5 Components of the Product Scope of delivery for SIMATIC HMI IPC477C Numbe Name Description SIMATIC HMI IPC477C Documentation and Drivers CD/DVD Contains the documentation and the hardware drivers. -
Page 7: Device Identification Data
Compact Operating Instructions 1.4 Device identification data Scope of delivery for SIMATIC HMI IPC477C PRO Numbe Name Description SIMATIC HMI IPC477C PRO Documentation and Drivers CD/DVD Contains the documentation and the hardware drivers. Operating instructions (compact) Printed copy in German and English of SIMATIC HMI IPC 477C / HMI IPC477C Operating Instructions (compact). -
Page 8: Accessories
Assign user specific functions to the keys as needed. You can mark these keys with labeling strips. A4 films for creating the labeling strips are available as accessories. Proceed as follows to affix the labeling strips: SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 9 Insert the labeling strips into the slots provided on the rear of the control unit. ① Insert strips, vertical key rows ② Insert strips, horizontal key rows Figure 1-1 12" touch screen device: Device rear with labeling strips SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
- Page 10 1.6 Affixing Labeling Strips for Function Keys and Softkeys ① Insert strips, vertical key rows ② Insert strips, horizontal key rows Figure 1-2 15" touch screen device: Device rear with labeling strips SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 11: Installing/Mounting
10 to 58 Hz: 0.075 mm 58 to 200 Hz: 9.8 m/s² – Storage/transport, tested according to IEC 60068-2-27, IEC 60068-2-29 50 m/s², 30 ms 250 m/s², 6 ms SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 12: Preparing The Mounting Cut-Out
Drill holes for the screws and pressure points for the clamp screws Note Mounting dimensions can be read from the dimension overview or they can be transferred to the cabinet from the mounting template supplied. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 13: Securing The Device With Clamps
You require 6 clamps in order to mount the device. These are supplied with the device. Required tool for fasting the clamps: Allen wrench 2.5 mm Figure 1-4 Clamp assembly SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 14 1. The material strength at the mounting cut-out must be at least 2 mm. 2. The deviation from the plane of the mounting cut-out in relation to the external dimensions for an installed HMI device is ≤ 0.5 mm. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 15: Securing The Device With Screws
Ensure that no metal cuttings enter the device when the holes are drilled. Cover the device with film or when drilling, use removal by suction. Figure 1-5 Designated location for holes on the control unit SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 16 Carefully drill the respective holes in the control unit at the designed location from the rear. Working from the front, insert the device into the mounting cut-out. Secure the control unit by inserting suitable screws through the holes and attaching nuts. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 17: Connecting
Figure 1-6 Variants with PROFIBUS ④ ETHERNET 1 RJ45 Ethernet connection for 10/100/1000 Mbps ⑥ PROFINET CP 1616 onboard interface, three RJ45 sockets Figure 1-7 Variants with PROFINET SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 18 Peripherals are developed and marketed by individual vendors. The respective manufacturers offer support for the peripherals. Moreover, the terms of liability of the individual vendors or suppliers apply here. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 19: Connecting The 24 Vdc Power Supply
Position of the on/off switch ① The on/off switch turns off the output voltages of the power supply without isolating the unit from mains. Delivery condition: Power switch turned off. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 20 (included in the scope of delivery). 4. Connect the PE conductor as described in section connecting the PE conductor (Page 21). The power consumption at 24 V amounts to 60 W maximum. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 21: Connecting The Pe Conductor
Steps for connecting the PE conductor 1. Remove the ten screws from the rear panel of the housing. 2. Lift up the rear panel slightly and then remove it. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 22: Commissioning
Note For information about the installation of the CompactFlash card with Windows Embedded Standard operating system, refer to the operating instructions. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 23: Basic Commissioning - Initial Startup
Errors and warnings can be displayed in the status bar, with the first and second switch on of the initial commissioning or after a restore procedure This will have no effect on the device functions. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 24: Setting Up The Language Selection In Windows Embedded Standard 2009
In addition to the menu and dialog language, select Regional and Language Options and set the default to non-Unicode programs in the Advanced section. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 25: Language Selection In Windows Embedded Standard 7
Note the license terms of Windows Embedded Standard 7 Please note the license terms for Windows Embedded Standard 7 and especially the extended SIEMENS AG Software terms for Windows Embedded Standard 7. You can find the license terms in the delivered document "MICROSOFT SOFTWARE LICENSE TERMS for Windows Embedded Standard 7(E)"... -
Page 26: Setting The Panel Type
Start the PC for commissioning in an unchanged delivery state and follow the dialogs until their conclusion. Procedure Device-specific drivers are set during the hardware detection and configuration phase. The type of SIMATIC PC is selected and detected automatically. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 27: Touch Panel Configuration
Compact Operating Instructions 1.9 Commissioning 1.9.5.2 Touch panel configuration Touch screen calibration 1. Calibrate the touch screen by clicking the wizard. 2. Click "Finish". SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 28: Key Panel Configuration
In Windows 7, the on-screen keyboard is not displayed until a password is assigned to the user account. 1. Use the "Finish" button to close the wizard.The HMI device will be restarted automatically for the respective configuration. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 29: Automatic Restart
F13 to S16 are used or if own key code tables are used. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 30: Device With Touch Screen
The entry is confirmed by a check mark, the next selection is displayed. 7. Confirm all input prompts (arrows, or crosses in the center) until the complete screen has been calibrated. 8. Finally, confirm the prompt with "Confirm". SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 31 If 3 point calibration does not suffice for the operator panel, you can clear it in the "Use eeprom storage" option box and use the standard calibration (25 point calibration). Currently only the Touch Controller "ELO 2216 (USB)" supports EEPROM calibration. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
- Page 32 If "Extended touch" is selected, the extended touch functions of Windows 7 will be available, such as "operating touch permanently", which corresponds to the right mouse button function. Note The "EventSelector" program works only with disabled "Extended touch" function. SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...
-
Page 33: Activating The Screen Keyboard
Starting Touch Input Start the "Touch Input" application on the desktop. The screen keyboard is displayed. (1) Button for language selection: German, English, Italian, Spanish, French SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 34: Service And Support
After-sales information system for SIMATIC PC / PG Information about contacts, drivers, and BIOS updates, FAQs and Customer Support can be found at: After-sales information system for SIMATIC PC/PG (http://www.siemens.com/asis) SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... -
Page 35: Index
Calling the screen keyboard, 33 Language selection Setup in Windows Embedded Standard 2009, 24 Windows Embedded Standard Setting up the operating system, 23 Mounting, 14 Mounting positions, 11 On-off switch SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02... - Page 36 Index SIMATIC HMI IPC477C / HMI IPC477C PRO Compact Operating Instructions, 10/2010, A5E02368072-02...