Supervisor Mode On/Off; Memory Initialize; Backup Data Send/Receive; Print At The End Of The Job - Sharp UP-810F Programming Manual

Table
File Name
No.
281 D-UPC (Refund) consol (Price1-6)
282 D-UPC (Refund) receive (Price1-6)
283 D-UPC (Coupon) save0 Daily (Price1-6)
284 D-UPC (Coupon) consol (Price1-6)
285 D-UPC (Coupon) receive (Price1-6)
286 AUTO COMBO BUFFER
#1 : Same as the number of record of table no. N
#2 : The number of table is same as the number of record of table no. N
- : (Number of index record) - (Number of data record)

9. SUPERVISOR MODE ON/OFF

[JOB#985]
SUPERVISOR MODE : SUPERVISOR
TEXT
S U P E RV I S O R ON/OFF
MODE
Note: Secret code for all modes are ignored when supervisor mode is
"ON".
10.MEMORY INITIALIZE (EXCEPT GT MEMORY)
[JOB#989]
MEMORY INITIAL : MEMORY INITIAL
TEXT
MEMORY INITIAL YES/NO
Totalizer memory initialize (except GT memory and EJ)
All of counter, totalizer are initialized. But, GT1-GT3, EJ memory is
remained.

11.BACKUP DATA SEND/RECEIVE

[JOB#996]
DATA SEND : DATA SEND
SEND DATA ALL
SSP
SPEED PROGRAMMED SPEED
38400 bps
19200 bps
9600 bps
4800 bps
2400 bps
[JOB#998]
DATA RECEIVE : DATA RECEIVE
SPEED PROGRAMMED SPEED
38400 bps
19200 bps
9600 bps
4800 bps
2400 bps
*
"PROGRAMMED" means "SPEED is specified by SRV#903-A".
Normal
keyboard
CONTENTS MRS
OFF
CONTENTS MRS
NO
UP-810F/820N/820F (U) SRV MODE PROGRAMMING ("SETTING")
Record
MRS
MAX #1
Flat
keyboard
****
0 47
****
0 47
****
0 47
****
0 47
****
0 47
0 99 74
DISPLAY during transmission
BACKUP SEND
SEND DATA
SPEED PROGRAMMED
+-----------------------------------------------+
| SENDING
|
+-----------------------------------------------+
PREV. NEXT LIST P DOWN
SRV SERV.0001
*
Customer Display is not changed.

PRINT at the end of the job

The message is printed on JOURNAL only.
Print
(30 digits)
(HEADER)
BACKUP SEND
SEND OK
(HEADER)
BACKUP RECEIVE
RECEIVE OK
COM. ERROR XX
DATA ERROR XX
COM. TIME-OUT
*
All ERROR MESSAGE are fixed.
*
ERROR CODE : 01 = ID No. error (ID No. in IDENQ is not correct.)
02 = Parity error
03 = Check sum error
04 = Data size error
05 = Hardware error
06 = Power off error
07 = Time out error
11 = Transmit data size error
12 = Block sequence error
13 = NAK code error
15 = ECR TYPE error
3 – 31
BLOCK
Label
Size
MRS MAX #2
0 6 0
0 6 0
0 6 0
0 6 0
0 6 0
1 1 1
P UP JOB title "BACKUP
SEND" or "BACKUP
ALL RAM
RECEIVE"
<<Key Area>>
00511 | "SENDING" or
"RECEIVING",
|
Counter Progress bar
0001
12:34 TIME DISPLAY is
freezed.
CONTENTS
JOB TITLE is printed.
MESSAGE is printed.
(This is Normal End Message)
JOB TITLE is printed.
MESSAGE is printed.
(This is Normal End Message)
ERROR MESSAGE, ERROR CODE
ERROR MESSAGE, ERROR CODE
ERROR MESSAGE
(Irregular sequence No. has been received)
(NAK code has been received.)
(Models of two ECR is different.)
Data
Size
9
9
9
9
9
102