Advertisement
Ô
Ô
NOTE
Connecting the Handset
Your local RadioShack store sells a variety of
longer coiled handset cords, which are
especially useful when you mount the phone
on a wall.
Set Up the Phone
Do not lift the handset from the base until the
Caller ID setup has been completed.
2
use screws with heads that fit into the
keyhole slots on the bottom of the base.
3. Plug one end of the supplied long
modular cord into the modular jack on
the back of the base.
4. Route the phone cord through the
groove on the bottom of the base,
securing the cord under the tabs.
5. Fit the heads of the screw into the
keyhole slots, then slide the base down
until it is secure.
6. Plug the other end of the cord into a
modular phone jack.
On a Desktop
1. Plug one end of the
supplied long modular
cord into the modular
jack on the bottom of
the base.
2. Route the phone cord
through the groove on
the base's bottom.
Secure the cord under
the tabs along the
groove.
3. Plug the other end of
the cord into a modular
phone jack.
C
H
ONNECTING THE
ANDSET
Plug one end of the supplied coiled cord into
the handset's modular jack, then connect
the other end to the jack on the bottom of
the telephone base. Ô
S
U
P
ET
P THE
HONE
d REVIEW e
1. Hold down both
ENTER LANGUAGE
four seconds until
ENG
ESP FRA
(flashing)
appear.
d
e
2. Press
or
to select the desired
language, then press
DELETE
LCD CONTRAST
1 2 3 4 5
confirm.
and
3
appear on the display, and
flashes.
d
e
3. Press
or
to select the contrast level
(from 1-5), then press
DELETE
ENTER AREA CODE
confirm.
appears, _ _ _
appears and the first _ flashes.
d
e
4. Press
or
to select the first number
of the area code. Press
DELETE
confirm the selection.
5. Repeat step 4 to select the second and
the third digit.
ENTER TIME DATE
6.
appears and the hour
digit flashes.
d
e
7. Press
or
to select the desired hour,
then press
to confirm.
DELETE
PM
appears for an AM hour,
appears for
a PM hour.
8. Repeat step 7 to set the minutes,
month, and day. Ô
S
ETTING THE
If you do not want to hear the phone ring,
slide
to
RINGER
OFF
calls with the ringer off, and you can answer
calls if you hear another phone on the same
phone line ring.
NEW
phone rings, even when the ringer is off.
S
ETTING THE
Slide
TONE/PULSE
for your type of service. If you are not sure
which service you have, do this simple test.
1. Slide
TONE/PULSE
handset and listen for a dial tone.
2. Press any number except
phone requires that you dial an access
code before you dial an outside number
(9, for example), do not press the
access code number.
• If the dial tone stops, you have
touch-tone service. Slide
TONE/PULSE
• If the dial tone continues, you have
pulse service. Slide
.
PULSE
U
S
SING
PECIAL
S
ERVICES
Some computer services, such as alternate
long distance, require tone signals for
communications. If you have pulse service,
you can still use special tone service by
following these steps.
1. Connect to the special service with
for about
set to
TONE/PULSE
, then
2. When the special service answers,
change
TONE/PULSE
* to temporarily switch to tone dialing.
to
3. When you complete the call, hang up
and return the setting to
OPERATION
to
M
C
AKING A
1. Pick up the handset and wait for a dial
tone.
to
2. Use the keypad to enter the number
you wish to dial. The dialed number
appears on the display. If you dial a
number over 15 digits, only the last 14
digits appear on the display.
3. When you complete your call, hang up.
A few seconds later, the number
AM
disappears, and the display returns to
normal.
R
INGER
. You can still make
flashes when the
D
M
IALING
ODE
to the appropriate setting
to
. Lift the
TONE
. If your
0
to
.
TONE
to
TONE/PULSE
T
ONE
.
PULSE
to
, or press
TONE
.
PULSE
ALL
Advertisement
