Related Manuals for Radio Shack 43-3905
Summary of Contents for Radio Shack 43-3905
- Page 1 43-3905 User’s Guide Caller ID Wall Phone Thank you for purchasing your Caller ID Wall Phone from RadioShack. Please read this user’s guide before installing, setting up, and using your new phone.
-
Page 2: Package Contents
Package contents • Caller ID Wall Phone • Short Phone Cord • User’s Guide Features • Caller ID memory stores information for up to 99 calls • Caller ID/Call Waiting ID display shows who’s calling • Backlit displays for better visibility at night or in low light • Traditional metal bell ringer • Heavy duty design Install Batteries 1. Lift the battery compartment cover from the top of the base, then remove the compartment. 2. Insert four AA batteries into the compartment as indicated by the polarity symbols (+ and –) marked inside. 3. Replace the battery compartment and cover. • Long Phone Cord • Coiled Cord • Quick Start... -
Page 3: Install Your Phone
Battery Notes: • During battery replacement, keep the line cord plugged in and replace the batteries within two minutes to maintain Caller ID memory. • When the low battery icon appears or the display dims, replace the batteries. • Make sure the batteries fit tightly in the battery compartment. • Dispose of old batteries promptly and properly. • Do not burn or bury batteries. • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. • If you do not plan to use the phone for two weeks or longer, remove the batteries. - Page 4 To mount the phone directly on a wall: 1. Drill two holes 3.25 inches (83 mm) apart, one below the other. 2. Thread a screw into each hole, letting the heads extend about 0.2 inch (5mm) from the wall. 3. Plug one end of the supplied long modular cord into the LINE jack at the back of the base. 4. Align the base’s keyhole slots with the installed screws and slide the phone downward to secure it. To connect the handset, plug one end of the supplied coiled cord into the handset’s modular jack. Then connect it to the jack on the left bottom of the base. Notes: • Your local RadioShack store sells a variety of longer coiled handset cords, which are especially useful when you mount the phone on a wall.
- Page 5 3-line Display Shows name, number, date and time of incoming calls. Flashes when you have new calls. DELETE Erases Caller ID information. CALL BACK Calls back the number shown on Caller ID. UP/DOWN Scroll through Caller ID records. M/S (Master/Secondary) Set to M. TONE/PULSE Set the dial mode for your phone system. VOLUME NORM/HI Set the call volume level. RINGER OFF/LO/HIGH Set the ringer volume or turn the ringer off.
-
Page 6: Phone Settings
at your local RadioShack store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules and the requirements adopted by the ACTA. The telephone cord and modular plug provided is Part 68 compliant for connecting to the telephone company network. Set Phone Options Phone Settings 1. Hold down both UP and DOWN for about four seconds until ENTER LANGUAGE, then ENG ESP FRA appear, with ENG flashing. -
Page 7: Dial Mode
Dial Mode Slide TONE/PULSE to the setting for the type of dialing service you have. If you are not sure which type you have, do this simple test. 1. Slide TONE/PULSE to TONE. Lift the handset and listen for a dial tone. 2. Press any number except 0. (If your setup requires that you dial an access code, usually 9, before you dial an outside number, do not press the access code number.) • If the dial tone stops, you have touchtone service. Keep the switch on TONE. • If the dial tone continues, you have pulse service. Set the switch to PULSE. Using Special Tone Services Some computer services require tone signals for communications. If you have pulse service, you can still simulate tone signals by following these steps. 1. Connect to the special service using pulse dialing. 2. When the special service answers, press switch to tone dialing. 3. When you complete the call, hang up to change the setting back to PULSE. Master/Secondary Setting For modern phones systems, slide M/S to M. Notes: • If you have other phones with a Master/Secondary switch, set them to S. Set one system to answer and set the others to off. -
Page 8: Operation
• Do not connect more than four Caller ID modules (including this phone) that do not have Call Waiting to the same phone line. • If you connect another type of Caller ID module that has Call Waiting to the same phone line as your system, the Call Waiting signal might be garbled or not received. Operation Making a Call 1. Pick up the handset and wait for a dial tone. 2. Use the keypad to enter the number you wish to dial. The number appears on the display. -
Page 9: Caller Id Operation
Using Flash If you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call. Note: If you do not have Call Waiting, pressing FLASH might disconnect the current call. Using Redial To redial the last number you called, pick up the handset and press REDIAL when you hear a dial tone. The number scrolls across the display, and the phone automatically dials it. Note: The redial memory holds up to 32 digits, so you can redial long distance as well as local phone numbers. Using Pause Some telephone systems require you to dial an access code (usually 9) and wait for a second dial tone before dialing an... - Page 10 During an incoming call, the phone company automatically sends the correct time between the first and second rings to update your system’s display. Review Call Records Press UP or DOWN to review the new calls. After all new calls have been reviewed, END OF NEW CALL appears. To review all the records from oldest to newest, press UP. To review the records from newest to oldest, press DOWN. After reviewing all records in memory, END OF LIST appears. • If an incorrect, invalid, or incomplete Caller ID signal is received, LINE ERROR appears on the display. • If the name and number are not available due to the caller’s restriction, PRIVATE CALL appears on the display. • If the name and number are not available, --UNAVAILABLE-- appears on the display. • RPT appears with a number if you have received a call from the same phone number more than once. • If you do not press a button within about 15 seconds, the system automatically returns to the normal display. Notes: • The NEW indicator remains flashing until you have reviewed all new calls.
-
Page 11: Delete Call Records
3. Lift the handset, and the number is redialed automatically. Follow these steps to select one of the options for Caller ID call back. 1. Press UP or DOWN to find the Caller ID memory location to be redialed. 2. Press CALL BACK. The 7- or 11-digit number flashes. 3. Press UP or DOWN to select one of the four options. Option 1 Option 2 Option 3 Option 4 4. Press CALL BACK again to confirm. 5. Pick up the handset, and the selected number is dialed automatically. Delete Call Records You can select and delete an individual call record, or all call records stored in the system. -
Page 12: Additional Information
• If you do not press any button within about 15 seconds while ERASE ALL CALLS appears on the display, the phone automatically returns to normal display and the records are not deleted. Additional Information Important Safety Information When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. -
Page 13: Surge Protection
Surge Protection Your telephone has built-in protection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone. Lightning damage is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that you unplug your phone when storms approach to reduce the possibility of damage. FCC Information FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your local RadioShack store or an experienced radio/TV technician for help. If you cannot eliminate the interference, the FCC requires that you stop using your equipment. Changes or modifications not expressly approved by RadioShack may cause interference and void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Part 68 and ACTA a) This phone complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. -
Page 14: Limited Warranty
Should a problem occur that is covered by this warranty, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store in the U.S. RadioShack will, at its option, unless otherwise provided by law: (a) repair the product without charge for parts and labor; (b) replace the product with the same or a comparable product; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period. RADIOSHACK EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED WARRANTY PERIOD. EXCEPT AS DESCRIBED ABOVE, RADIOSHACK SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RADIOSHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. You may contact RadioShack at: RadioShack Customer Relations, 300 RadioShack Circle, Fort Worth, TX 76102 Protect the environment by recyling used electronics. Go to E-CyclingCentral.com to find an electronic recycling center near you. ©2009. RadioShack Corporation. All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation. www.RadioShack.com 04/08 Printed 11A09 in China 43-3905 4LM053Y2...