Table of Contents
Advertisement
E E n n g g i i n n e e e e r r i i n n g g T T e e s s t t s s
" " A A " " C C o o n n t t r r o o l l
The following tests are available and may be
entered from a power up or power reset mode.
To Enter engineering tests, press "Set" and "Delay
Start" simultaneously. Use "<" and ">" to scroll to
the desired test, then press "Set" to start the test.
Press the "START/CANCEL" key to exit.
The following is the menu of the engineering tests.
W W a a t t e e r r / / T T u u r r b b i i d d i i t t y y
C C o o n n t t - - H H e e a a v v y y W W a a s s h h
C C o o n n t t - - N N o o r r m m a a l l W W a a s s h h
C C o o n n t t - - S S h h o o r r t t W W a a s s h h
R R e e l l a a y y T T e e s s t t
C C - - R R e e l l a a y y T T e e s s t t
S S o o f f t t w w a a r r e e I I . . D D . .
U U I I - - E E r r r r o o r r s s
P P o o w w e e r r E E r r r r o o r r s s
D D i i s s p p l l a a y y W W a a t t e e r r T T e e m m p p e e r r a a t t u u r r e e a a n n d d T T u u r r b b i i d d i i t t y y V V o o l l t t a a g g e e s s
T T e e s s t t M M o o d d e e
Simultaneously hold the "Delay Time" and "Set"
keys during power-up. When "Water Turbidity" is
displayed, press 'Set' and select a Wash Cycle,
press START/CANCEL and close door. The digital
display shows the water temperature in °F and the
static and dynamic turbidity readings in volts.
An open sensor will read 3.8 Volts and a shorted
sensor, 0 Volts.
To cancel, press "Start/Cancel" key, unit will drain,
open door and press simultaneously "Delay Time"
and "Set" keys.
C C o o n n t t i i n n u u o o u u s s W W a a s s h h M M o o d d e e
This test was developed to run in the reliability labs
for relays life tests. Simultaneously hold the
"Delay Time" and "Set" keys during power-up to
enter diagnostics. Use the arrow keys to scroll to
the Cont-S Wash test. The display will show data
for the Wash Mode selected. Run continuous
wash cycle repeatedly according to the Wash
Tables. Press the "START/CANCEL" key to exit.
E E l l e e c c t t r r o o n n i i c c C C o o n n t t r r o o l l
D D i i s s c c r r e e t t e e R R e e l l a a y y / / T T r r i i a a c c a a n n d d S S e e n n s s o o r r T T e e s s t t
To enter this mode, press the "Delay Time" and
"Set" keys simultaneously. The dishwasher enters
a program for all control tests, press one of the
arrows to either side of the display until the
Relay/Triac test reads in the display. Press the
"Set" key to select the test. Once in the Relay/
Triac test, pressing the arrows selects the compo-
nent to be tested. To start the test, press the "Set"
key. When the test is complete, press the "Set"
key to end the test. To exit the Relay/Triac test,
press and hold the "Set" key, this will reset the
control and "WELCOME" scrolls across the
readout.
C C - - R R e e l l a a y y T T e e s s t t
To enter this mode the "Delay Time" and "Set"
keys will be used. Selection of the Relay Test will
be done by using the ">" or "<" keys to page and
the "Set" key to select this test. This mode may
be exited by resetting the machine.
S S o o f f t t w w a a r r e e V V e e r r s s i i o o n n
Simultaneously hold the "Delay Time" and "Set"
keys and then select the software ID test option.
The software version numbers of the user
interface, the baseboard, and the wash table's will
alternate on the display.
W W a a t t e e r r S S e e r r v v i i c c e e T T e e s s t t - - F F r r o o m m I I d d l l e e M M o o d d e e
Simultaneously press the "Wash Cycles" & "Delay
Time" keys for three seconds. Press the "Set" key
and close door to run the water service test.
A A c c c c e e p p t t a a n n c c e e T T e e s s t t s s
To Enter press "<" and ">" simultaneously.
Use "<" and ">" to select the desired test.
Press "Set" to Start test.
To setup the next test run:
Select Desired Test
Press "Start"
Disconnect power from unit.
3-11
Hide quick links:
Advertisement
Table of Contents
