I I n n s s t t a a l l l l a a t t i i o o n n I I n n f f o o r r m m a a t t i i o o n n
C C o o n n n n e e c c t t i i o o n n s s F F o o r r E E l l e e c c t t r r i i c c a a l l , , W W a a t t e e r r , , a a n n d d D D r r a a i i n n
(Continued)
6. Pull electrical cable through hole into
installation area.
7. Be sure water inlet valve is protected from
freezing. If valve freezes and ruptures, flooding
may occur.
8. Determine amount of tubing needed to
connect hot water supply to the unit's water
inlet valve. Extra hose length is necessary.
High-pressure and high-temperature stainless
flexible hose with a minimum inner diameter of
1/4" may be used. A shut-off valve installed
outside the dishwasher cabinet is best.
9. Route water supply line into installation area.
10. Stand dishwasher back upright for further
installation.
I I M M P P O O R R T T A A N N T T : : Incoming hot water temperature
should be at least 120°F (49°C). Water pressure
should be between 20–120 psi.
D D r r a a i i n n H H o o s s e e C C o o n n n n e e c c t t i i o o n n
CAUTION
P P r r o o p p e e r r t t y y D D a a m m a a g g e e
D D o o n n o o t t u u s s e e t t h h e e f f u u r r n n i i s s h h e e d d d d r r a a i i n n h h o o s s e e o o r r a a r r u u b b b b e e r r
g g a a r r d d e e n n h h o o s s e e f f o o r r t t h h e e w w a a t t e e r r s s u u p p p p l l y y l l i i n n e e . . E E i i t t h h e e r r o o f f
t t h h e e s s e e h h o o s s e e s s c c a a n n b b u u r r s s t t . . F F l l o o o o d d i i n n g g m m a a y y o o c c c c u u r r a a n n d d
c c a a u u s s e e p p r r o o p p e e r r t t y y d d a a m m a a g g e e . .
N N O O T T E E : : Pull the hose from "End Storage Location"
side. (See Figure 2-4)
1. Take drain hose out of dishwasher and find the
end that doesn't have the black rubber
material.
2. Use only the spring clamp that is provided in
the accessory kit, place spring clamp over one
of the hoses. (See Figure 2-5)
3. Take the plastic side of the drain hose and
insert it into the hose that is already attached
to the dishwasher make sure hose ends are
flush against each other. (See Figure 2-6)
4. Secure the spring clamp 1/8" from large end of
black hose to the plastic side that was inserted
for best sealing results.
F F i i g g u u r r e e 2 2 - - 4 4 . . D D r r a a i i n n H H o o s s e e S S t t o o r r a a g g e e L L o o c c a a t t i i o o n n
F F i i g g u u r r e e 2 2 - - 5 5 . . C C o o n n n n e e c c t t i i n n g g D D r r a a i i n n H H o o s s e e
Plastic Ends Of Hoses Flush
Hose Attached
to Dishwasher
F F i i g g u u r r e e 2 2 - - 6 6 . . C C o o n n n n e e c c t t i i n n g g D D r r a a i i n n H H o o s s e e
2-6