Table of Contents
Advertisement
TROUBLESHOOTING
•
When playing back a source encoded with DTS
SYMPTOM
CAUSE
REMEDY
Refer to
page
A loud hissing noise is
The pIaye
I
which plays back the SOUlce is not
The playci must be connected to a digital audio
14
heard when playing back
connected to a digital audio signal input
signal input tel minal of this unit besides the
a source encoded with
telminal of this unit
analog audio signal tet minal connections
DTS
The input mode is set to ANALOG on this unit
Set a propel input mode to tuln on the built-in
23
OTS decodel
A percussive noise is
If the input mode is set to AUTO depending on
Set the input mode of the cUlIently selected
23
heard when playing back
some SOUlces thele may be a noise heald while
input soulce to OTS
a source encoded with
this unit is identifying the
l'
01
mat of the input
DTS
signal
No sound is heard when
The built-in OTS decodel does not function
Set the playel
's
digital volume conlIol at the
-
playing back a source
because the playel has a digital volume contr 01
maximum neutIaIOl inetTective position
encoded with DTS, even
and it is set at a position othel than
if the input mode is set
"maximum' "neutral
01
"ineffective
to AUTO on this unit
No sound is heard when
A source encoded with OTS cannot be recorded
~
-
playing back an MD or
on an MO
01
OAT
DAT on which has been
recorded a source
encoded with DTS
No sound is heard when
In
the AUTO mode, the OTS-decoding mode
Set the input mode to AUTO again
24
playing back a source
cannot be automatically changed to the nOl mal
(CD, etc) even if the
(peM) digital signal input mode
currently selected input
mode is AUTO
necessmy to use a DTS decodel to play back a SOlllce encoded with DTS, so the playel which plays back the SOUlce must be connected
to a digital audio input telIuinal of this unit in the way desclibed in this manual If this connection is not made or only a D-to-A COnveltel is
being used without using a DTS decodel. only a loud hissing noise will be hemd when you play back the SOlllce
• The
"~"
indicatOl will flash when the input mode is set to AUTO and a seatch
01
skip opelation is pelfolIued while playing back a
SOUlce encoded with DTS
If
this status continues
1'01 3001
mOle seconds, the unit will automatically switch flOm DTS-decoding mode to
peM digital signal input mode and the
"~"
indicatol will go out
I
53
TROUBLESHOOTING
•
When playing back a source encoded with DTS
SYMPTOM
CAUSE
REMEDY
Refer to
page
A loud hissing noise is
The pIaye
I
which plays back the SOUlce is not
The playci must be connected to a digital audio
14
heard when playing back
connected to a digital audio signal input
signal input tel minal of this unit besides the
a source encoded with
telminal of this unit
analog audio signal tet minal connections
DTS
The input mode is set to ANALOG on this unit
Set a propel input mode to tuln on the built-in
23
OTS decodel
A percussive noise is
If the input mode is set to AUTO depending on
Set the input mode of the cUlIently selected
23
heard when playing back
some SOUlces thele may be a noise heald while
input soulce to OTS
a source encoded with
this unit is identifying the
l'
01
mat of the input
DTS
signal
No sound is heard when
The built-in OTS decodel does not function
Set the playel
's
digital volume conlIol at the
-
playing back a source
because the playel has a digital volume contr 01
maximum neutIaIOl inetTective position
encoded with DTS, even
and it is set at a position othel than
if the input mode is set
"maximum' "neutral
01
"ineffective
to AUTO on this unit
No sound is heard when
A source encoded with OTS cannot be recorded
~
-
playing back an MD or
on an MO
01
OAT
DAT on which has been
recorded a source
encoded with DTS
No sound is heard when
In
the AUTO mode, the OTS-decoding mode
Set the input mode to AUTO again
24
playing back a source
cannot be automatically changed to the nOl mal
(CD, etc) even if the
(peM) digital signal input mode
currently selected input
mode is AUTO
necessmy to use a DTS decodel to play back a SOlllce encoded with DTS, so the playel which plays back the SOUlce must be connected
to a digital audio input telIuinal of this unit in the way desclibed in this manual If this connection is not made or only a D-to-A COnveltel is
being used without using a DTS decodel. only a loud hissing noise will be hemd when you play back the SOlllce
• The
"~"
indicatOl will flash when the input mode is set to AUTO and a seatch
01
skip opelation is pelfolIued while playing back a
SOUlce encoded with DTS
If
this status continues
1'01 3001
mOle seconds, the unit will automatically switch flOm DTS-decoding mode to
peM digital signal input mode and the
"~"
indicatol will go out
I
53
Advertisement
Table of Contents
