Table of Contents
Advertisement
CONNECTI
•
Speaker cables
2~
D
Remove approx 10 mm (3/8") of insulation
from each of the speaker cables.
~
Twist the exposed wires of the cable together
to prevent short circuits.
•
Connecting to the MAIN SPEAKERS terminals
•
Connecting to the REAR and CENTER SPEAKERS terminals
Red: positive (+)
Black: negative (-)
Red: positive (+)
Black: negative (-)
D
Unscrew the knob
~
Insert one bare wire into the hole in the side of
each terminal.
~
Tighten the knob to secure the wire
D
Open the tab
~
Insert one bare wire into the hole of each
terminal
~
Return the tab to secure the wire.
'"
~<i>~
Banana plug connections ,lie also possible FilSt. tighten the knob
and then inset t the banana plug conneetol into the end of the
cOllcsponding tellninal
•
Connecting to an external amplifier
The speaket connections desctibed on page 16 ate fine fot most applications If you wish to dtive yoU! existing amplifiet, the
following tetminals ate available fot connecting an extetnal amplifiet(s) to this unit
Note
• Uutput signals flam these telminals ate alTected by the use ofYOLUME. BASS TREBLE and BALANCE
• It an extclnal amplifiel is connected to the MAIN. CENTER
01
REAR OUTPUT tellninals. disconnect the cOllesponding
speakeI' (main. centel
01
Ical) hom the SPEAKERS tell11inals
17
(U S A model)
o
MAIN OUTPUT terminals
These tetminals ate fot the main channel line output
Connect the input tetminals of the extetnal amplifiet to
these tetminals
f)
CENTER OUTPUT terminals
These tel1ninals ate fot the center channel line output
Connect the input tetminals of the extetnal amplifier to
these tel1ninals
•
REAR (SURROUND) OUTPUT terminals
These tel1ninals are f01 the tear channel line output
Connect the input tet minals of the external amplifier to
these tel1ninals
Note
I
CONNECTI
•
Speaker cables
2~
D
Remove approx 10 mm (3/8") of insulation
from each of the speaker cables.
~
Twist the exposed wires of the cable together
to prevent short circuits.
•
Connecting to the MAIN SPEAKERS terminals
•
Connecting to the REAR and CENTER SPEAKERS terminals
Red: positive (+)
Black: negative (-)
Red: positive (+)
Black: negative (-)
D
Unscrew the knob
~
Insert one bare wire into the hole in the side of
each terminal.
~
Tighten the knob to secure the wire
D
Open the tab
~
Insert one bare wire into the hole of each
terminal
~
Return the tab to secure the wire.
'"
~<i>~
Banana plug connections ,lie also possible FilSt. tighten the knob
and then inset t the banana plug conneetol into the end of the
cOllcsponding tellninal
•
Connecting to an external amplifier
The speaket connections desctibed on page 16 ate fine fot most applications If you wish to dtive yoU! existing amplifiet, the
following tetminals ate available fot connecting an extetnal amplifiet(s) to this unit
Note
• Uutput signals flam these telminals ate alTected by the use ofYOLUME. BASS TREBLE and BALANCE
• It an extclnal amplifiel is connected to the MAIN. CENTER
01
REAR OUTPUT tellninals. disconnect the cOllesponding
speakeI' (main. centel
01
Ical) hom the SPEAKERS tell11inals
17
(U S A model)
o
MAIN OUTPUT terminals
These tetminals ate fot the main channel line output
Connect the input tetminals of the extetnal amplifiet to
these tetminals
f)
CENTER OUTPUT terminals
These tel1ninals ate fot the center channel line output
Connect the input tetminals of the extetnal amplifier to
these tel1ninals
•
REAR (SURROUND) OUTPUT terminals
These tel1ninals are f01 the tear channel line output
Connect the input tet minals of the external amplifier to
these tel1ninals
Note
I
Advertisement
Table of Contents
