Table of Contents
Advertisement
CONTROLS AND FUNCTIONS
4D
AlB/C/D/E, PRESET
+/-
These buttons are used to select a preset station
AlB/C/DIE:
To select one of a group (A to E) of preset
stations
PRESET +/-: To select a preset station number (I to 8)
48
v
(next),
A
(back)
These buttons are used to advance or go back one selection
on the SET MENU and TIMEILEVEL mode
~ SET MENU
Press this button to select the items on the SET MENU
4D
POWER
Press this button to turn this unit on
4I;
STANDBY
Press this button to set this unit in the standby mode
~ VOLUME (+/-)
These buttons are used to adjust the volume level
4fI
MUTE
Press this button to mute the sound To cancel mute, press
this button again
EFFECT
Press this button to turn on or off the effect speakers (center
and teat) in the following cases:
• When the selector dial is set to the DSP/TUN position
• While the indicator is lit fOl about three seconds after
ptessing DSP
The Numeric buttons function in various ways depending
on the position of the selector dial or the combination of
other instructions
•
When selecting an input source
D
Press INPUT regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6
You can select an input source with the
numeric buttons while the indicator is lit.
8
•
When selecting a DSP program
and turning on or off the effect
speakers (center and rear)
A
B
A
o
Press DSP regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6
You can select a DSP program with the
numeric buttons (1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT while the indicator is lit.
B
D
Set the selector dial to the DSPITUN position.
6
You can select a DSP program directly with the
numeric buttons (1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT.
•
When selecting a preset station
number
D
Set code number "0023" in the AMPITUN (or
DSPITUN) position.
Refet to page 48 for setting the code
6
Set the selector dial to the AMPITUN (or DSP/
TUN) position.
!J
You can select a preset station number directly
with the numeric buttons (1 to 8).
Refer to page 29
CONTROLS AND FUNCTIONS
4D
AlB/C/D/E, PRESET
+/-
These buttons are used to select a preset station
AlB/C/DIE:
To select one of a group (A to E) of preset
stations
PRESET +/-: To select a preset station number (I to 8)
48
v
(next),
A
(back)
These buttons are used to advance or go back one selection
on the SET MENU and TIMEILEVEL mode
~ SET MENU
Press this button to select the items on the SET MENU
4D
POWER
Press this button to turn this unit on
4I;
STANDBY
Press this button to set this unit in the standby mode
~ VOLUME (+/-)
These buttons are used to adjust the volume level
4fI
MUTE
Press this button to mute the sound To cancel mute, press
this button again
EFFECT
Press this button to turn on or off the effect speakers (center
and teat) in the following cases:
• When the selector dial is set to the DSP/TUN position
• While the indicator is lit fOl about three seconds after
ptessing DSP
The Numeric buttons function in various ways depending
on the position of the selector dial or the combination of
other instructions
•
When selecting an input source
D
Press INPUT regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6
You can select an input source with the
numeric buttons while the indicator is lit.
8
•
When selecting a DSP program
and turning on or off the effect
speakers (center and rear)
A
B
A
o
Press DSP regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6
You can select a DSP program with the
numeric buttons (1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT while the indicator is lit.
B
D
Set the selector dial to the DSPITUN position.
6
You can select a DSP program directly with the
numeric buttons (1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT.
•
When selecting a preset station
number
D
Set code number "0023" in the AMPITUN (or
DSPITUN) position.
Refet to page 48 for setting the code
6
Set the selector dial to the AMPITUN (or DSP/
TUN) position.
!J
You can select a preset station number directly
with the numeric buttons (1 to 8).
Refer to page 29
Advertisement
Table of Contents
