Table of Contents
Advertisement
F-4
RANGER 9 / K867 / LN-8 CONNECTION DIAGRAM
RANGER 9 / K867 / LN-8 CONNECTION DIAGRAM
14 PIN
14 PIN
AMPHENOL
AMPHENOL
TO WORK
TO WORK
ELECTRODE
ELECTRODE
TO WORK
TO WORK
CAUTION :
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
THE ENGINE WELDER OPERATING MANUAL.
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.
N.B. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
N.B. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITION. PLACE WELDING TERMINALS SWITCH TO
PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITION. PLACE WELDING TERMINALS SWITCH TO
"REMOTELY CONTROLLED " POSITION.
"REMOTELY CONTROLLED " POSITION.
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.D. SPLICE LEADS AND INSULATE.
N.D. SPLICE LEADS AND INSULATE.
N.E. PLACE IDLER SWITCH IN "HIGH" IDLE POSITION.
N.E. PLACE IDLER SWITCH IN "HIGH" IDLE POSITION.
14 PIN
AMPHENOL
TO WORK
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
N.A. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
PLACE WELDER TERMINALS SWITCH TO "REMOTELY CONTROLLED" POSITION.
N.B. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
APPLICATIONS. SEE OPERATING MANUAL.
N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITIION.
N.D. PLACE IDLER SWITCH IN "AUTO" OR "HIGH" IDLE POSITION AS DESIRED.
DIAGRAMS
WARNING
WARNING
Do not operate with panels open.
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
before servicing.
Do not touch electrically live parts.
Do not touch electrically live parts.
K867 UNIVERSAL
K867 UNIVERSAL
ADAPTER PLUG
ADAPTER PLUG
ELECTRODE CABLE
ELECTRODE CABLE
TO WIRE FEED UNIT
TO WIRE FEED UNIT
RANGER 9 / LN-742 CONNECTION DIAGRAM
WARNING
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
K592 CONTROL CABLE
ELECTRODE
TO WORK
RANGER 9
Keep guards in place.
Keep guards in place.
Keep away from moving parts.
Keep away from moving parts.
Only qualified personnel should install,use
Only qualified personnel should install,use
or service this equipment.
or service this equipment.
SPARE
SPARE
82
82
81
81
N.C.
N.C.
42
42
41
41
31
31
31
31
32
32
32
32
2
2
2
2
4
4
4
4
21
21
21
21
GND
GND
GND
GND
75
75
A
A
76
76
B
B
77
77
C
C
N.D.
N.D.
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.
TO LN-742 INPUT
CABLE PLUG
ELECTRODE CABLE
TO WIRE FEED UNIT
F-4
LN-8
LN-8
WIRE
WIRE
FEEDER
FEEDER
K196
K196
INPUT CABLE
INPUT CABLE
12-16-93
12-16-93
M17094
M17094
12-16-93
M17100
Advertisement
Table of Contents
