Remote Control; Components; Operating Other Components; Storing The Remote Control Code Of The Other Components - Kenwood KRF-X9060D Instruction Manual

Basic remote control operations for other components

Operating other components

This operation lets you operate the registered components.
KENWOOD audio components with system control turn on and off
automatically with the receiver via the system control connections.
INPUT
SELECTOR
1
Use the INPUT SELECTOR keys to select the component you
desire.
• Pressing the INPUT SELECTOR keys also changes the input selector
on the receiver.
• When you operate your registered DVD player, CD player, Cable
tuner, DSS/SAT receiver, VCR or TV, go to step 2.
• When you operate the CD player, Cassette deck, MD player, or
Tuner with system control connection, go to step 3.
2
Press the SOURCE key.
• To return to the receiver operation mode, press the RECEIVER key.
3
Press the operation keys you desire.
The remote control mode remains at the selected input. If you
wish to operate another component, repeat step 2 or 3.
Note
Be sure to point the remote control at the remote sensor on the
receiver when you want to operate KENWOOD components connected
by system control cords. Otherwise, point the remote control at the
component you want to operate.
Storing the remote control code of the other

components

The remote control unit can store the remote control code of the other
components and you can operate the other components from the remote
control unit. The remote control code is stored on the key or memory of
the remote control unit.
Storing on the key
You can store the remote control code to the key as shown below:
LEARN key
SOURCE
Numeric keys
CH + / –
Skip ¢/4
DVD
TOP MENU
OSD
PAGE fi/%
RETURN
1 Rewind
¡ Fast forward
DISC SEL
DISC SKIP
42 EN
SOURCE
RECEIVER
SOURCE POWER
LEARN
DVD CBL DSS/SAT RECEIVER
REMOTE MODE
VCR TV OTHERS THX
1 2 3
LISTEN MODE
4 5 6
ACTIVE EQ
7 8 9
SPEAKER EQ
0
+10 +100
INPUT MODE STEREO DSP MODE MUTE
TV CONTROL
¢ + +
+
VOL.
4
- INPUT -
-
SEL
CH VOLUME
MENU
TOP MENU MENU
SET UP SOUND
Cursor 5/∞/2/3
P.CALL P.CALL
4 /DOWN /UP ¢
™ ENTER £
ENTER
MULTI
CONTROL
OSD RETURN
PAGE
3/8 (Play/Pause)
TUNING FLIP BAND 2 Flip
1 ¡ 2 6
8 Pause
8
INPUT SEL A/B AUTO
7
DISC SEL DISC SKIP DIMMER
7 Stop
DVD/6CH CD/DVD PHONO TUNER
VIDEO 1 VIDEO 2 VIDEO 3 MD/TAPE
INPUT SELECTOR
1 Point the infrared ray system part of another remote control unit
to the remote sensor of the remote control unit.
2 Press the LEARN key.
• This remote control is ready to receive the remote control code from
the other source.
3 Press any of the REMOTE MODE (DVD, CD, CBL, DSS/SAT, CBL/
SAT, VCR, TV, OTHERS) keys to select the input of the desired
remote control unit.
4 Press the desired key of the remote control unit.
5 From the remote control unit of the other source, press the key
that you want to store.
• The remote control code is sent to the remote control unit.
• "OK" appears when finished.
y
• When the appropriate code is not properly stored, "AGAIN" will be
displayed. Repeat from step 2 onwards.
• If the code cannot be stored after a few attempts, "ERROR" will
appear. Repeat from step 2 onwards.
• If LEARN mode's storage is full, "FULL" appears on the display.
6 The remote control code is stored on the key of this remote
control unit.
7 Press the LEARN key again to exit the learning mode.

Remote control

unit of the other
source.
Infrared ray system part
LEARN
LEARN
LEARN
LEARN