Preparing For Surround Sound; Speaker Settings - Kenwood KRF-V8030D Instruction Manual

Preparing for surround sound

Speaker settings

14
To enable you to obtain optimum enjoyment from the receiver's listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
MULTI CONTROL
ON/STANDBY
POWER
Display operation 1
Display operation 2
1
Turn on the power to this receiver by pressing POWER
(and ON/STANDBY) key(s).
2
Select a speaker system.
1 Press the SETUP key to make the subwoofer setting indication
(SUBW) appear.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
When you operate on the remote control unit
1 Press the display operation 2 [Menu] key repeatedly until
"01.IR" appears in the display of the remote control unit.
>01.IR
>02.Surround
Home Enter
2 Press the 5/∞ keys to select "02.Surround", then press the
display operation 2 [Enter] key.
SetUp
Home Next
(SUBW) appears in the display of the unit.
2 Use the MULTI CONTROL knob or the 5/∞ keys to select the
appropriate subwoofer setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• When the setting "SUBW NO" is selected, the front speakers automati-
cally are set to "Large" and the procedure skips to step 5.
SETUP
5/∞
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
3 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The front speakers setting indication (FRNT) appears.
SP A B TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
4 Use the MULTI CONTROL knob or the 5/∞ keys to select the
appropriate front speakers setting.
1 FRNT NML (normal): Average size front speakers are
2 FRNT LRG (large):
5 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The center speaker setting indication (CNTR) appears.
6 Use the MULTI CONTROL knob or the 5/∞ keys to select the
appropriate center speaker setting.
If you selected "LRG" as the front speakers setting.
1 CNTR NML (normal): An average size center speaker is con-
2 CNTR LRG (large):
3 CNTR NO:
If you selected "NML" as the front speakers setting.
1 CNTR YES: A center speaker is connected to the
2 CNTR NO:
7 Press the SET UP or display operation 2 [Next] key to accept the
setting.
AUTO
• The surround speaker setting indication (SURR) appears.
MEMO
ST.
TUNED
8 Use the MULTI CONTROL knob or the 5/∞ keys to select the
appropriate surround speaker setting.
If you selected "LRG" as the center speaker setting.
1 SURR NML (normal): Average size surround speakers are
2 SURR LRG (large):
3 SURR NO:
If you selected other than "LRG" as the center speaker setting.
1 SURR YES: Surround speakers are connected to the re-
2 SURR NO:
9 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected channels of
the speakers that require adjusting.
L C R
LFE SW
LS S RS
connected to the receiver.
Large front speakers are connected
to the receiver.
nected to the receiver.
A large center speaker is connected to
the receiver.
No center speaker is connected to the
receiver.
receiver.
No center speaker is connected to the
receiver.
connected to the receiver.
Large surround speakers are con-
nected to the receiver.
No surround speakers are connected
to the receiver.
ceiver.
No surround speakers are connected to the
receiver.
Continued to next page
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX DSP