Series Transmitters Table - ADEMCO Vista-10SE Installation And Setup Manual

The wireless system can identify a true low-battery situation, thus allowing the dealer or
user of the system time to arrange a change of battery and maintain protection for that point
within the system.
Some transmitters (e.g., 5802, 5802CP, and 5804) contain long-life but nonreplaceable
batteries, and no battery installation is required. At the end of their life, the complete unit
must be replaced (and a new serial number enrolled by the control).
Button-type transmitters (such as 5801, 5802, 5802MN/MN2, 5802CP, and 5804) should be
periodically tested for battery life.
The 5802MN and 5804 Button Transmitters have replaceable batteries.
Using the Transmitter Sniffer Mode
The Transmitter Sniffer mode is a procedure that verifies that all transmitters have been
properly programmed. To verify programming, refer to the TESTING THE SYSTEM section.
Model Description
5801 Wireless Panic
Transmitter
5802 Pendant Belt Clip
(Personal Emergency)
5802CP
Transmitters
5802MN Miniature Personal
Emergency Trans.
5802MN2
5804 Wireless Key
5804BD Transmitter
5806 Wireless Photoelectric
Smoke Detectors
5807
5808
Low-profile version
5807L
of the Wireless
5807LT
Photoelectric Smoke
5807LST
Detectors
5808LST
HeatSensor, 135 º
5809
Detector/Transmitter
5816 Door/Window
5816MN Transmitter
5816 Low Temp Sensor
TEMP
5817 Multi-Point Universal
Transmitter

5800 Series Transmitters Table

Input Type and Special Notes
Enroll as "3" for RF (supervised), or "4" for UR (unsupervised).
Unit has 4 pushbuttons, each with a unique input (loop) code.
Each pushbutton must be assigned to a zone.
NOTE: Input loop (button) No. 4 must always be used.
Enroll as "5" for BR (button-type transmitter).
Enroll as "3" for RF (supervised), or "4" for UR (unsupervised).
Single pushbutton-type transmitter.
Enroll as "5" for BR (button-type transmitter).
Has 4 pushbuttons, each with a unique input (loop) code.
Each pushbutton must be assigned to a zone.
NOTE: All buttons must be assigned the same input type.
Enroll as "3" for RF (supervised).
At the "INPUT S/N" prompt, fault the detector as follows:
1. On many detectors, you must press a special test switch (not test button) to
fault the detector (see detector's instructions).
NOTE: With some detectors, you must short two contacts to fault the
detector. Disengage the detector's cover and swing it open. These contacts
are on the PC board near a blue jumper (see detector's instructions).
Momentarily short these contacts with a small screwdriver.
Two keypad beeps occur when the detector is faulted the first time.
2. Wait 6 to 8 seconds, then press and release the test switch (or momentarily
short the contacts) again. If the control has accepted the input code, 3 beeps
sound and the enrolled input (loop) number is displayed.
Enroll as "3" for RF (supervised).
Has two unique input (loop) zones: one for a wired closed-circuit contact loop,
and the other for a built-in reed switch (used in conjunction with a magnet).
Either or both may be used.
Enroll as "3" for RF (supervised).
Has three unique input (loop) codes: one for a DIP switch-set "Primary" contact
loop, and the others for two "Auxiliary" closed-circuit contact loops.
The "Primary" loop may be set for:
•
Repeating or Single Transmission
•
Normally Open or Normally Closed circuit
•
Slow or Fast Response
3-Minute or no Transmission Inhibit
WWW.DIYALARMFORUM.COM
Section 5 - Wireless Expansion
5-5