Programming Options - ADEMCO Vista-10SE Installation And Setup Manual

VISTA-10SE Installation and Setup Guide
4204 Setup
The 4204 unit can be mounted either remotely or in the control panel. The following steps
should be taken to properly set up the 4204:
1. Connect the 4204 to the control's remote keypad terminals (4–7), using the
connector supplied with the 4204. Use standard 4-conductor twisted cable for long
OFF ON
wiring runs.
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ @ @
@ @ h ? @ @ h ? @ @ @ @
@ @ h ?
@ @ h ? @ @ h ? @ @ @ @ 2. Set the 4204's DIP switch for a device address of "1" (switch 2 "OFF" and switches
@ @ h ? @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ 3, 4, and 5 "ON"). Switch 1 determines the unit's cover tamper response ("ON" =
@ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
disabled, "OFF" = enabled).
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ 3. Connect the desired field wiring to the unit's relay contact terminals. See Figure 10
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @
below.
Supervision
4204 modules are supervised against removal. CHECK and zone 09 will be displayed if a
module is disconnected from the control's keypad terminals (4, 5, 6, and 7).
4204
COVER TAMPER (REED) SWITCH

Programming Options

In the VISTA-10SE, each device must be programmed as to how to act (ACTION), when to
activate (START), and when to de-activate (STOP). Refer to the programming procedures for
80 and 81 interactive modes that are provided in the MECHANICS of PROGRAMMING,
OUTPUT DEVICE PROGRAMMING, and ZONE LISTS sections for specific programming
details.
6-2
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
4-PIN KEYPAD PLUG
EITHER OR BOTH
CAN BE USED
TB1
13 14 15 16
Figure 10. 4204 Connections to Control
WWW.DIYALARMFORUM.COM
RELAY
4
TYPICAL
(SHOWN "OFF")
RELAY
RELAY
RELAY
YEL
DATA IN
FROM CONTROL
BLK
(–) GROUND
GRN
DATA OUT
TO CONTROL
RED
(+) 12V
C
NC
NO
C
3
NC
NO
C
2
NC NC
NO
C
1
NC
NO
TB2
V10SE-016-V0