JVC HR-DD840U Instructions Manual page 45

SET PROGRAM
INFORMATION
5
Press the appropriate NUMBER keys to set the date,
start/stop time and channel number. Press CH5 ∞ or
TIME SCAN5 ∞ to set AM/PM and tape speed (SP or
EP). Press OK after AM/PM, channel number and tape
speed settings.
* If you are using a DBS receiver, see "ATTENTION FOR
DBS RECEIVER USERS" in the right column.
Any information comprised of 1 digit (except the
channel number) should have a "0" entered before it.
It is possible to set all information using the CH 5 ∞ or
TIME SCAN 5 ∞ button.
(In this case, press OK after each setting.) Do not use
the CH ∞ or TIME SCAN∞ button to set the date.
At the Program Set screen, the setting that can be set
blinks. When setting of a highlighted item is completed,
the highlight bar moves down by 1 line to the next item.
If you are using the Illumi-Guide feature, OK blinks
when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
** You can record selected programs at the same time
every weekday, or once a week. Before entering the
month, press NUMBER key "8" (DAILY) or "9"
(WEEKLY). Either "DAILY" or "WEEKLY" appears.
Press again and "DAILY" or "WEEKLY" disappears.
For weekly recording, the desired date for the day of
the week must be entered.
MAKE CORRECTIONS
6
To change any of the settings, press OK or TIME SCAN
™ £ until the item you want to change begins
blinking. Then set as in step 5.
If you are using the Illumi-Guide feature, OK blinks
when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
RETURN TO NORMAL
SCREEN
7
Press MENU as many times as necessary.
Press just once to access the Auto Timer screen
( pg. 47).
If you are using the Illumi-Guide feature, all buttons
go out.
ENGAGE TIMER MODE
8
Press TIMER. The VCR turns off automatically.
EXAMPLE
If you program the VCR to timer
record a show on December 24
on channel 40 from 12:00 noon
to 1:00 PM in SP mode, the
screen will look like this:
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS receiver
(unless "DBS RECEIVER OUT-
PUT" is set to "OFF" pg.21),
the BAND indication (TV or
CATV or DBS) appears to the
right of the channel number dis-
play. If the channel number that
has been entered requires that
the band be set, the BAND in-
dication starts blinking:
a- TV : To timer-record a regular TV program received
on the VCR.
b- CATV : To timer-record a cable TV program received on
the VCR, or through a cable box (unless
"CABLE BOX OUTPUT" is set to "OFF"
c- DBS : To timer-record a satellite program received
through a DBS receiver.
Press CH5∞ or TIME SCAN5 ∞ to select the appropriate
band, then press OK.
If "BAND" is set to "TV" at the Band screen (
CATV will not be displayed on the Program screen; if it is
set to "CATV", TV will not be displayed.
NOTES:
To disengage the timer before recording starts, press TIMER
again. Pressing once more re-engages it.
In case of a power failure after programming, the VCR's memory
backup keeps your selections for approximately 10 minutes.
If you select "PROGRAM SET" without having set the date and
time, an error message appears. Follow its instructions.
If you enter a start time that has already passed, "ERROR"
appears on the screen and blinks.
Programs that start after midnight must have the next day's date.
After timer recording is completed, the VCR's power goes off
automatically.
You can program the timer while a regular recording is in
progress; the on-screen menu will not be recorded.
If the end of tape is reached during timer recording, the
cassette is automatically ejected.
When timer-recording cable or satellite channels through an
external tuner, be sure to keep the cable box or satellite
receiver's power ON.
45
EN
PROGRAM 1
DATE 12/24 WED
START 12:00 PM
STOP 1:00 PM
CHANNEL 40 SP
PRESS NUMBER KEY (O–9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
PROGRAM 1
DATE 12/24 WED
START 12:00 PM
STOP 1:00 PM
CHANNEL 110 DBS SP
PRESS NUMBER KEY (O–9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
pg.16).
pg.13),