Page 1: Table Of Contents
QU ICK SET U P GU ID E QU ICK SET U P GU ID E ON REA R SID E ON REA R SID E VIDEO CASSETTE RECORDER CO N TEN TS SAFETY FIRST HR-D D 4 4 5 EK Safety Precautions ......
Page 2: Video Cassette Recorder
SAFETY FIRST Sa fety Preca utions The rating plate and the safety caution are on the rear of the unit. WARN IN G: D AN GERO U S VO LTAGE IN SID E WARN IN G: TO PREVEN T FIRE O R SH O CK H AZARD , D O N O T EXPO SE TH IS U N IT TO RAIN O R M O ISTU RE.
Page 3: Some Do's And Don'ts
Some Do's And Don'ts O n The Sa fe Use O f Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. read the operating instructions before you attempt to use the equipment.
Page 4: Installing Your New Recorder
IN STALLIN G YO U R N EW RECO RD ER Ba sic Connections Back of TV RF Cable (provided) 21-pin SCART Cable (not provided) Aerial connector 21-pin AV input connector (SCART) It's essential that your video recorder be properly connected. Follow these steps carefully.
Page 5 TV Aerial Cable (not provided) ANT. IN AV1 IN / OUT RF OUT AV2 IN Back of Recorder ATTEN TIO N If you have finished all the necessary connections, go to "Video Channel Set" on page 6, then perform Auto Set Up on page 8; do NOT press the button on the recorder/remote control to turn on the recorder's power before you start Auto Set Up.
Page 6: Initial Settings
IN ITIAL SETTIN GS If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to V ideo "W ith RF Connection" below. If you have connected the video recorder to your TV Cha nnel Set via both the provided RF cable and a 21-pin SCART cable (AV connection) –...
Page 7 IM PO RTAN T: Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder. W ith AV Connection ACCESS VIDEO CHAN N EL ¡ SET MO DE Press and hold down STO P on the recorder until the display panel shows the following.
Page 8: Auto Set Up
IN ITIAL SETTIN GS (cont.) The Auto Set Up function sets the tuner channels, clock and Video Plus+ assigned Guide Program numbers automatically Auto Set Up when the button on the recorder/remote is first pressed to power on the recorder after you plug the mains power cord into a mains outlet.
Page 9 Auto Set Up results a ppea r on the displa y pa nel ● When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed. ● When auto channel set has been completed successfully but auto clock set has not, "CH"...
Page 10: Video Plus+ Setup
IN ITIAL SETTIN GS (cont.) With Video Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number V ideo Plus+ which your recorder is able to recognise. N O TE: Setup “ Guide Program (GUIDE PROG) number" refers to the assigned TV station numbers, according to broadcast area, for Video Plus+ timer recording.
Page 11 W hen Using A Sa tellite ENTER PLUSCODE NUMBER Receiver And/ O r Ca ble Press O K , and a cursor GUIDE PROG SET appears above “ GUIDE System 1 2 3 4 5 PROG” . Then, using the N U M BER keys, input the GUIDE PROG TV PROG...
Page 12: Playback
PLAYBACK The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video Ba sic tape are read by your video recorder and displayed on your TV just like a TV programme. Pla yba ck LO AD A CASSETTE Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is...
Page 13: Playback Features
Take advantage of special functions possible with the recorder’s controls or the remote control. Pla yba ck Still Picture/ Fra me-By-Fra me Fea tures Pla yba ck P AUSE DURIN G PLAYBACK Press PAU SE. If there is vertical jitter, use the TV PRO G buttons to correct the picture.
Page 14 PLAYBACK (cont.) M a nua l Tra ck ing Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PRO G buttons. STO P ¡ O VERRIDE AUTO MATIC TRACKIN G Press on the remote to engage manual tracking.
Page 15 Index Sea rch Repea t Pla yba ck Your recorder automatically marks Your video recorder can automatically play back the whole tape £ 2 index codes at the beginning of 20 times repeatedly. each recording. This function gives you quick access to any one of 9 index codes in either direction.
Page 16: Timescan
PLAYBACK (cont.) Your recorder is equipped with the TimeScan function. TimeScan allows noise free pictures to be displayed on your TV TimeSca n screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the TimeScan modes pg.
Page 17 TimeScan Reverse Forward N ames of special-effects playback Search Play Slow-Motion *Still Slow-Motion Play Search -9x -7x -5x -3x -1/6x -1/18x 1/18x 1/6x 2x 3x 5x 7x 9x Speed SP -1/6x -1/18x 1/18x 1/6x Speed LP Audio is not Audio is Audio is not Audio output Audio is output.
Page 18: Recording
RECO RD IN G TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “ capture” a TV programme Ba sic using your video recorder. LO AD A CASSETTE Recording Insert a cassette with the record safety tab intact. ●...
Page 19: Recording Features
Record O ne Progra mme Recording W hile W a tching Another Fea tures SELECT PRESET TO WATCH Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.
Page 20: Picture System
RECO RD IN G (cont.) The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and B.E.S.T . playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “...
Page 21 N O TES: ● The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. ● In the case of timer recording, the B.E.S.T. system works before recording is initiated.
Page 22: Tim Er Recording
TIM ER RECO RD IN G ACCESS TIMER PRO GRAMMIN G V ideo Plus+ SCREEN Press PRO G Timer TIMER PROGRAMMING Recording [0 – 9] : VIDEO PLUS+ [+/–] : EXPRESS PROGRAMING [MENU] : MAIN MENU The front display panel looks like this: Before performing Video Plus+ Timer Recording: ●...
Page 23 SET T APE SPEED Press SP/ LP ( ) to set the tape speed. RETURN TO N O RMAL SCREEN Press O K . ● Repeat steps 1 – 5 for each additional programme. ¡ EN GAGE RECO RDER’S TIMER MO DE Press TIM ER .
Page 24: Regular Timer Programming
TIM ER RECO RD IN G(cont.) If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder Regula r Tim er to timer-record the programme. ACCESS TIMER Progra m m ing PRO GRAMMIN G SCREEN Press PRO G Remember, the clock must be set before you can progamme...
Page 25 EN TER PRESET PO SITIO N Press TV PRO G +/ – . – P1 – START STOP 21:00 22:00 DATE TV PROG 25. 12 BBC 1 ¡ [+/–] = [MENU] : EXIT IM PO RTAN T Be sure to confirm the setting of PDC recording. ●...
Page 26 TIM ER RECO RD IN G(cont.) Check And Ca ncel Progra mmes ACCESS PRO GRAMME DISPLAY AN D/ O R SCREEN Press PRO G CH ECK. ● The display panel shows the programme start time. Pressing O K changes the display to the programme stop time, then the date and preset position.
Page 27 Auto Timer When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MEN U SCREEN Press M EN U twice. ACCESS MO DE SET TIM ER SCREEN...
Page 28: Editing
ED ITIN G You can use your video recorder as the source player or the recording deck. Edit To O r MAKE CO N N ECTIO N S From Another Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated below. When Using Your Video Recorder As The Source Player .
Page 29: Edit From A Camcorder
You can use a camcorder as the source player and your video recorder as the recorder. Edit From A MAKE CO N N ECTIO N S Ca m corder Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's rear panel AV2 IN or AV1 IN/OUT connector via the optional cable adapter.
Page 30: System Connections
SYSTEM CO N N ECTIO N S The AV2 IN socket on the rear panel of your recorder allows simple connection to a satellite receiver. Connection To A Sa tellite Receiver Aerial Outdoor Unit TV Aerial cable Satellite Cable Satellite Receiver U nit ANT.
Page 31 Aerial terminal Back of TV 21-pin SCART connectors EXT.2 EXT.1 ANT. IN RF OUT Downloaded from: https://www.usersmanualguide.com/...
Page 32: Special Features
SPECIAL FEATU RES O n-Screen Dispia y Turn on the TV and select the VIDEO channel (or AV mode). You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. TURN O N THE RECO RDER Press ACCESS MAIN MEN U...
Page 33 Ta pe Position Indica tor The tape position indicator appears on screen when, from the Stop mode, you press FF , REW or perform an Index Search. The position of “ 5 ” in relation to “ 0” (beginning) or “...
Page 34: Tuner Set
TU N ER SET IM PO RTAN T Auto Cha nnel Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( pg. 8) or if you have moved to a different area or if a new station starts broadcasting in your area.
Page 35 VIEW CO N FIRMATIO N SCREEN The stations your recorder located appear on a BBC1 – – – – Confirmation screen — BBC2 – – – – – – – – preset positions (PR), – – – – channels (CH) and station –...
Page 36: Manual Channel Set
TU N ER SET (cont.) Storing Cha nnels M a nua lly M a nua l Store channels that were not stored during Auto Set Up ( 8) or Auto Channel Set ( pg. 34). Cha nnel Set ACCESS MAIN MEN U Press M EN U twice.
Page 37 Perform steps 1 and 2 of "Storing Channels Manually" on page 36 to access the Confirmation screen before continuing. Delete A Cha nnel SELECT ITEM Press PU SH JO G % ﬁ until the item you want to delete begins blinking. CAN CEL DELETE CHAN N EL Press CAN CEL .
Page 38 TU N ER SET (cont.) Perform steps 1 and 2 of "Storing Channels Manually" on page 36 to access the Confirmation screen before continuing. Set Sta tions (A) SELECT ITEM Press PU SH JO G %ﬁ until the item you want begins blinking.
Page 39 Perform steps 1 and 2 of "Storing Channels Manually" on page 36 to access the Confirmation screen before continuing. Fine-Tuning Cha nnels Alrea dy Stored SELECT CHAN N EL TO FIN E-TUN E Press PU SH JO G % ﬁ until the channel you want to tune begins blinking.
Page 40 TU N ER SET (cont.) TV Sta tion And ID List STATIO N N AM E ID * STATIO N N AM E ID * Anglia TV ANGL SAT 1 SAT1 ARTE ARTE Scottish TV SCOT BBC Group BBC1 BBC1 BBC2 BBC2 SDR1...
Page 41 TV Sta tion Cha nnel N umber Guide O nly the main stations are listed. There are in addition many relay stations, and full lists are available from BBC and ITC. BBC1 BBC2 BBC1 BBC2 London & South-East N orth-W est Bluebell Hill ......
Page 42: Clock Set
CLO CK SET IM PO RTAN T Clock Set Perform the following steps only if Auto Clock Set has not been performed correctly by Auto Set Up ( pg. 8) or Auto Channel Set ( pg. 34) or if the recorder's memory backup has expired.
Page 43 Auto Clock Set SET CLO CK AUTO MATICALLY At the Clock Set screen, press PU SH JO G . The AUTO CLOCK Auto Clock Set screen appears and clock setting PLEASE WAIT begins. JUST CLOCK: ON TV PR. ● If "TV PR." isn't set to the preset position on which Auto Clock Set data is received, "ERROR"...
Page 44: Troubleshooting
TRO U BLESH O O TIN G Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. PO W ER SYM PTOM POSSIBLE CAUSE...
Page 45 TIM ER RECO RDIN G POSSIBLE CAUSE CORRECTIVE ACTION SYM PTOM ● The clock and/or the timer have Re-perform the clock and/or timer 1. Timer recording won’t work. been set incorrectly. settings. ● The timer is not engaged. Press TIMER and confirm that “ ‰ “ is displayed on the display panel.
Page 46: Questions And Answ Ers
Q U ESTIO N S AN D AN SW ERS PLAYBACK RECORDING Q . W hat happens if the end of the tape is reached Q . W hen I pause and then resume a recording, the end during playback or search? of the recording before the pause is overlapped by A.
Page 47: Specifications
SPECIFICATIO N S GEN ERAL TU N ER/ TIM ER : AC 220 – 240 V ` , 50/60 Hz Power requirement TV channel storage Power consumption : 20 W capacity : 99 positions Temperature (+AUX position "AU") Operating : 5°C to 40°C Tuning system : Frequency synthesized tuner Storage...
Page 48: Index
IN D EX FRO N T VIEW STANDBY/ON COUNTER TIMER TV PROG RESET SP/ LP ¡ TIM ER Button engages timer standby mode. STO P/ EJECT Button stops tape; ejects tape pg. 23, 25 during Stop mode. pg. 12 Button turns recorder on/off D isplay Panel provides clear view of various STAN D BY/ O N (loading a cassette also turns power on).
Page 49 REAR VIEW ANT. IN AV1 IN / OUT RF OUT AV2 IN Mains Power Cord supplies power to recorder. AV2 IN Connector enables connection of pg. 4 satellite receiver or second recorder; input AV1 IN / O U T Connector enables AV connec- recordable when "AU 2"...
Page 50 IN D EX (cont.) REM O TE CO N TRO L D ISPLAY Button switches display between clock time, tape remaining time, counter & readings, preset position*. pg. 19 * Preset position is not displayed during playback. TV/VCR TV Button enables remote control of your J VC DISPLAY (MONITOR) "Operating J VC TVs"...
Page 51 ● Point the remote control toward the sensor window. ● The maximum operating distance of the remote control is about 8 m. O perating JVC TVs To operate your TV, while holding down TV , press the corresponding button: STAN D BY/ O N , TV/ VCR, TV (TV Mute).
Page 52 VICTOR COMPANY OF JAPAN, LIMITED Downloaded from: https://www.usersmanualguide.com/...
Page 53 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...

JVC TIME SCAN HR-DD445EK Instructions Manual

Quick Links

Related Manuals for JVC TIME SCAN HR-DD445EK

Summary of Contents for JVC TIME SCAN HR-DD445EK

Table of Contents