HELIX H901 Assembly Manual
  1. Manuals
  2. Brands
  3. HELIX Manuals
  4. Fitness Equipment
  5. H901
  6. Assembly manual
HELIX H901 Assembly Manual

HELIX H901 Assembly Manual

Aerobic lateral trainer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Aerobic Lateral Trainer
Please read carefuly before using.

Advertisement

Table of Contents
loading

Related Manuals for HELIX H901

Summary of Contents for HELIX H901

  • Page 1 Aerobic Lateral Trainer Please read carefuly before using.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION Important Safety Precautions Weight Limit Capacities Warning BEFORE YOU BEGIN Unpacking Information Pre-Assembly Check List Pre-Assembly Check List Drawing ASSEMBLY 4-10 GETTING STARTED Computer Instructions 11-12 CUSTOMER INFORMATION Customer Service READ ALL INSTRUCTIONS BEFORE USING - 1 -...

  • Page 4: Important Safety Information

    10. This machine is intended for household use only. It is not designed for commercial use. IMPORTANT!!! THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR YOUR Helix is 130Kg (286 lbs.) per user.

  • Page 5: Before You Begin

    IMPORTANT: Read all instructions carefully. Assemble the Helix in accordance with the steps in the manual. All tools required for assembly are included with your Helix. Lay out all parts on the floor. Make sure that you have all the parts listed below before beginning assembly. In case of a discrepancy, please contact our Customer Service Department at the email address or customer service number listed on Page 11 of this Owner¹s Manual.

  • Page 6: Assembly

    Attach the End Caps (2) to the Left and Right Frame Legs. These caps are not specific to either side. They fit on left or right. If the Helix is not stable on the floor, turn the adjuster on the front end cap to raise or lower the height.
  • Page 7 3/ ASSEMBLY Separate the Pedal Covers from the Pedal frames as shown in FIG 4 STEP 4: Holding the Pedal Frame as shown, align the bolt holes on the pedal frame with the bolts on the yoke of the Crank arm. There is an indentation on the Pedal Frame and a protrusion on the yoke.
  • Page 8 3/ ASSEMBLY The back can be determined by the opposite side of the Tension Adjustment Knob. After sliding on the Rubber Circle, then slide on the “Removeable Cover” The cover should be installed with the hole toward the back side of the Upright so that the majority of the cover sits on the front of the Center Upright Tube.
  • Page 9 3/ ASSEMBLY Take sleeve out Next, Turn the Tension adjustment knob all the way to the left to level one. This should release the tension on the black “sleeve” that is surrounding the cable as shown in Figure #7. If the adjustment has not completely loosened the tension on the sleeve, Pull up on the Center Upright Tube as shown in Figure #6 on previous page.
  • Page 10 3/ ASSEMBLY STEP 9: Remove elastic cord from around the tension adjuster knob and then cut the cord to remove from the cover. Slide the cover down to the bottom of the center upright tube and fit the tabs into the holds in the lower plastic housing to fit snuggly in place as shown.
  • Page 11 3/ ASSEMBLY STEP 11: There should now be 3 wires. two coming from the handle bars and one that you held from the upright when installing the handle bars. Hold all three wires together as shown in Figure #1 above. Take Top Cover (part #9) and position with the notch in the rear to allow wires to come out.
  • Page 12 3/ ASSEMBLY COMPUTER INSTALLATION STEP 13: Prepare Computer for installation. See Picture #1. Remove 4 bolts and extend 3 wires from the back of the computer. Do not install batteries in holder at this time. Note square ridge that will match up with metal computer bracket on handlebars.

  • Page 13: Getting Started

    4/ GETTING STARTED - COMPUTER TOTAL RESET KEY Press to total reset and come back initial setting mode. ( set CLOCK / RESET KEY Press key to reset function value to 0 CALENDAR / TIME) for reset. RECOVERY KEY Measure user’s recovery level. UP-Increase function value.
  • Page 14 To count up from Zero, just begin exercising and the computer will start automatically to count up from zero. If this is not your first time using the Helix, you must first reset the values of each category to zero.
  • Page 15 - 13 -...
  • Page 16 For customer service, we first recommend you contact the dealer where you purchased the Helix. They will be able to resolve any issues the fastest. If you cannot reach the dealer, please feel free to contact Helixco at 888-Helixco or by email to customer@helixco.com Distributed under license from Kriptonite Corp by Helixco, a division of M &...

Table of Contents