Mitsubishi Electric FR-F740-00023 Instruction Manual page 75

4.14 Energy saving operation and energy saving monitor
4.14.1 Energy saving control and Optimum excitation control (Pr. 60)............................................................................. 147
4.14.2 Energy saving monitor (Pr. 891 to Pr. 899)............................................................................................................. 148
4.15 Motor noise, EMI measures, mechanical resonance
4.15.1 PWM carrier frequency and Soft-PWM control (Pr. 72, Pr. 240, Pr. 260) ............................................................. 153
4.15.2 Speed smoothing control (Pr. 653, Pr. 654)............................................................................................................ 154
4.16 Frequency setting by analog input (terminal 1, 2, 4)
4.16.1 Analog input selection (Pr. 73, Pr. 267)................................................................................................................... 155
4.16.2 Analog input compensation (Pr. 73, Pr. 242, Pr. 243, Pr. 252, Pr. 253)................................................................ 160
4.16.3 Response level of analog input and noise elimination (Pr. 74) .............................................................................. 161
4.16.4 Bias and gain of frequency setting voltage (current)
(Pr. 125, Pr. 126, Pr. 241, C2(Pr. 902) to C7(Pr. 905)) .......................................................................................... 162
4.16.5 4mA input check of current input (Pr. 573).............................................................................................................. 167
4.17 Misoperation prevention and parameter setting restriction
4.17.1 Reset selection/disconnected PU detection/PU stop selection (Pr. 75) ................................................................ 169
4.17.2 Parameter write selection (Pr. 77) ........................................................................................................................... 172
4.17.3 Reverse rotation prevention selection (Pr. 78)........................................................................................................ 173
4.17.4 Display of applied parameters and user group function (Pr. 160, Pr. 172 to Pr. 174) .......................................... 173
4.18 Selection of operation mode and operation location
4.18.1 Operation mode selection (Pr. 79)........................................................................................................................... 175
4.18.2 Operation mode at power on (Pr. 79, Pr. 340)........................................................................................................ 183
4.18.3 Start command source and speed command source during
communication operation (Pr. 338, Pr. 339, Pr. 550, Pr. 551) ............................................................................... 184
4.19 Communication operation and setting
4.19.1 Wiring and configuration of PU connector............................................................................................................... 189
4.19.2 Wiring and arrangement of RS-485 terminals ........................................................................................................ 191
4.19.3 Initial settings and specifications of RS-485 communication
(Pr. 117 to Pr. 124, Pr. 331 to Pr. 337, Pr. 341, Pr. 549)........................................................................................ 194
4.19.4 Communication EEPROM write selection (Pr. 342)............................................................................................... 195
4.19.5 Mitsubishi inverter protocol (computer link communication)................................................................................... 196
4.19.6 Modbus-RTU communication specifications
(Pr. 331, Pr. 332, Pr. 334, Pr. 343, Pr. 539, Pr. 549).............................................................................................. 207
4.20 Special operation and frequency control
4.20.1 PID control (Pr. 127 to Pr. 134, Pr. 241, Pr. 553, Pr. 554, Pr. 575 to Pr. 577,
C42 (Pr. 934) to C45 (Pr. 935))................................................................................................................................ 219
4.20.2 Bypass-inverter switchover function (Pr. 135 to Pr. 139, Pr. 159) ......................................................................... 231
4.20.3 Advanced PID function (pump function) (Pr. 554, Pr. 575 to Pr. 591)................................................................... 236
4.20.4 Traverse function (Pr. 592 to Pr. 597) ..................................................................................................................... 246
4.20.5 Regeneration avoidance function (Pr. 882 to Pr. 886) ........................................................................................... 248
4.21 Useful functions
4.21.1 Cooling fan operation selection (Pr. 244)................................................................................................................ 250
4.21.2 Display of the life of the inverter parts (Pr. 255 to Pr .259)..................................................................................... 251
4.21.3 Maintenance timer alarm (Pr. 503, Pr. 504)............................................................................................................ 254
4.21.4 Current average value monitor signal (Pr. 555 to Pr. 557)..................................................................................... 255
4.21.5 Free parameter (Pr. 888, Pr. 889) ........................................................................................................................... 257
4.22 Setting from the parameter unit, operation panel
4.22.1 PU display language selection (Pr. 145) ................................................................................................................. 258
4.22.2 Operation panel frequency setting/key lock selection (Pr. 161)............................................................................. 258
4.22.3 Buzzer control (Pr. 990) ........................................................................................................................................... 260
4.22.4 PU contrast adjustment (Pr. 991) ............................................................................................................................ 260
4.23 Parameter clear
4.24 All parameter clear
4.25 Parameter copy and parameter verification
4.25.1 Parameter copy ........................................................................................................................................................ 263
4.25.2 Parameter verification .............................................................................................................................................. 264
4.26 Check and clear of the faults history
66
147
153
155
169
175
189
219
250
258
261
262
263
265