Sanyo PLC-XT35 Service Manual page 70

Electrical Adjustment
Group/
Item Name
Item
3 Shipping Setting
4 CABLE SW
5 PW Debug Command Enable
6 Device Refresh Disable
7 Device Access Disable
8 PJ-Net HangUp Check
9
10
11
12
13
14
15
20 Projector Time Reset
21 Lamp Warning Time (NORMAL)
22 Lamp Warning Time (ECO)
23 Lamp Warning Time (HIGH)
30 Lamp life test enable
31 Lmap On time(for life test)
32 Lamp Off time(for life test)
33 Lamp total time(for life test)
50 Lamp Replacement Display
51 Filter Warning Display
52 Lamp counter Reset Times
53 Filter Counter Reset times
54 Factory Default Execute Times
55 Motor Stop
56 Mouse Posiyion (X)
57 Mouse Position (Y)
58 Lamp Go Out
80 Panel life test mode
Group 201 Option (signal)
0 FrameLock Option
1
2 Field Sense Invert Enable
3
4 Sub Image Enable
5
6 Zoom Accelerator Enable
7 DZoom Reset by Keystone
8 Stability Count
9 Sensivity for Signal Lost (HSYNC)
10 Sensivity for Signal Lost (VSYNC)
11 Keystone Filter center value
12
13
14
15
Group 205 Spread Spectrum
0 Spread Spectrum Enable
Function
Long Cable
Lamp Life at Normal Mode (Warning Time at
Normal)
Lamp Life at Eco Mode (Warning Time at
Eco)
Lamp Life at Eco Mode (Warning Time at
High)
For test purpose
For test purpose
For test purpose
Lamp Warning Display On/Off
Filter Warning Display On/Off
Reset Times of Lamp Counter
Reset Times of Filter Counter
Reset Times of Factory Default Set
Motor Stop 0: Enable, 1: Disable
Offset Value of X axis
Offset Value of Y axis
Lamp go out
Panel life test mode
0: Life test mode, 1: Normal
Count Value of V-missing
Only used this value for No Signal
Judgement(Hz)
Only used this value for No Signal
Judgement(Line)
Center value of Keystone Filter
0: Spectrum-on, 1: Spectrum-off
Initial
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
1
0
1
0
0
5
350
3
16
1
-70-
Range Note
0 - 20 Default set when the value is set to 10.
* Not used
0:Disable (Serial Command Eanble)
0 - 1
1: Enable (PW Debug Mode)
0:Enable, 1:Disable
0 - 1
No last memory
0:Enable (Normal), 1:Disable
0 - 1
No last memory
0 - 1 0: Enable, 1: Disable
* Not used
* Not used
* Not used
* Not used
* Not used
* Not used
* Not used
Projector Time is cleared when the value is
0 - 20
set to 10.
500 - 8000
500 - 8000
500 - 8000
0:Disable 1:Enable, for safety test only
0 - 1 0: Off, 1: On
0 - 1 0: Off, 1: On
0 - 255 * Read only
0 - 255 * Read only
0 - 255 * Read only
0 - 1
0 - 1024
0 - 1024
0 - 1
0 - 1
0: FrameLockOFF at PC signal
0 - 1 1: FrameLockON at PC signal and 47Hz
(Vfreq) ~ Panel frequency of input signal
* Not used
Reverse Processing of FLDINVSetting Value
0: Disable - Used FLDINV Setting Value
0 - 1
1: Enable - Used Reversed FLDINV Setting
Value
* Not used
0:Disable (Service Adjustment Dsiable,
0 - 1 Used all the Center Values
1:Enable (Service Adjustment Enable)
* Not used
0:Zoom Accelerator OFF,
0 - 1 1:Zoom Accelerator ON
No last memory
0:Enable (Normal), 1:Disable (Dzoo is not
0 - 1 cancelled even if Keystone is cancelled)
No last memory
0 - 255
0 - 32767
0 - 255
0 - 30
* Not used
* Not used
* Not used
* Not used
0 - 1