Philips Q552.2L Service Manual page 50

EN 50 6. Q552.2L LA
Option & Bit Dec. Value
Bit 0 (LSB) 1
Option 8 (prescribed value 00012
Bit 15 (MSB) 32768
Bit 14 16384
Bit 13 8192
Bit 12 4096
Bit 11 2048
Bit 10 1024
Bit 9 512
Bit 8 256
Bit 7 128
Bit 6 64
Bit 5 32
Bit 4 16
Bit 3 8
Bit 2 4
Bit 1 2
Bit 0 (LSB) 1
Note
1). Example
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the "NVM editor" and "Dealer options"
items in SAM (do not forget to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. This action also
ensures the correct functioning of the "Net TV" feature and
access to the Net TV portals. The loading of the CTN and
production code can also be done via ComPair (Model number
programming).
After a SSB repair, the original channel map can be restored,
provided that the original channel map was stored on a USB
stick before repair was commenced and that basic functionality
of the TV, needed for this procedure, was not hampered as a
result of the defect. The procedure of "channel map cloning" is
clearly described in the (electronic) user manual.
6.6 Total Overview SAM modes
Table 6-12 SAM mode overview
Main Menu Sub-menu 1
Hardware Info A. SW version
B. Stand-by processor version e.g. "STDBY_83.84.0.0"
C. Production code
Operation hours
Errors
Reset error buffer
2012-Mar-16
Alignments
Option Name
FAN
1)
)
Test 8
Test 7
Test 6
Test 5
Test 4 (Trick Mode)
Test 3 (XRay)
Test 2 (DBV-T light)
Test 1 (Monitor out)
not used
WM DRM10
HBBTV
DVB-T2 Installation
DVB-T2
Sub-menu 2
e.g. "Q5551_0.9.1.0
e.g. "see type plate"
1)
Prescribed Value Description
1)
0 0 = no fan
1 = fan(s) present)
1)
0 -
1)
0 -
1)
0 -
1)
0 -
1)
0 0 = OFF
1 = ON
1)
0 0 = OFF
1 = ON
1)
0 0 = OFF
1 = ON
1)
0 0 = OFF
1 = ON
1)
0000 -
1)
1 0 = OFF
1 = ON
1)
1 0 = OFF
1 = ON
1)
0 0 = OFF
1 = ON
1)
0 0 = OFF
1 = ON
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
6.5.1 SSB identification
Whenever ordering a new SSB, it should be noted that the
correct ordering number (12nc) of a SSB is located on a sticker
on the SSB. The format is <12nc SSB><serial number>. The
ordering number of a "Service" SSB is the same as the ordering
number of an initial "factory" SSB.
Sub-menu 3
back to
div. table
18310_221_090318.eps
Description
Display TV & Stand-by SW version and CTN serial
number
Displays the accumulated total of operation hours.TV
switched "on/off" & every 0.5 hours is increase one
Displayed the most recent errors
Clears all content in the error buffer
090319