Table of Contents
Advertisement
EN 46
6.
Q552.2L LA
•
When finished press OK on the RC, then press STORE (in
the SAM root menu) to store the aligned values to the NVM.
•
Restore the initial picture settings after the alignments.
Table 6-3 White tone default setting 32" sets (Blockbuster)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-4 White tone default setting 40" sets (Blockbuster)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-5 White tone default setting 32" sets (Emmy)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-6 White tone default setting 40" sets (Emmy)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-7 White tone default setting 46" sets (Emmy)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-8 White tone default setting 42" sets (Sundance)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-9 White tone default setting 47" sets (Sundance)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-10 White tone default setting 40" sets (Berlinale)
White Tone
Colour Temp
Normal
Cool
Warm
2012-Mar-16
Alignments
e.g. 32PFL6606/xx
R
G
B
112
127
85
106
127
100
125
126
53
e.g. 40PFL6606/xx
R
G
B
117
127
95
113
127
111
126
125
60
e.g. 32PFL7606/xx
R
G
B
112
127
85
106
127
100
125
126
53
e.g. 40PFL7606/xx
R
G
B
115
127
84
111
127
99
125
127
49
e.g. 46PFL7606/xx
R
G
B
124
127
98
120
127
121
127
121
58
e.g. 42PFL8606/xx
R
G
B
125
125
127
106
108
127
127
110
79
e.g. 47PFL8606/xx
R
G
B
126
122
122
112
111
127
127
114
80
e.g. 40PFL5806/xx
R
G
B
121
126
121
107
116
127
127
121
83
6.4
Option Settings
6.4.1
Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
PNX51XX ICs (back-end advanced video picture improvement
IC which offers motion estimation and compensation features
(commercially called HDNM) plus integrated Ambilight control)
is made known by the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
•
The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2
Dealer Options
For dealer options, in SAM select "Dealer options".
See Table
6-12 SAM mode
6.4.3
(Service) Options
From 2011 onwards, it is not longer possible to change
individual option settings in SAM. Options can only be changed
all at once by using the option codes as described in section
6.4.4.
6.4.4
Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set.
Example: The options sticker gives the following option
numbers:
•
08192 00133 01387 45160
•
12232 04256 00164 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicate software options 5 to 8.
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
Diversity
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM => an alternative BOM number usually
indicates the use of an alternative display or power supply. This
results in another display code thus in another Option code.
Refer to Chapter
Connections.
6.4.5
Option Code Overview
Refer to the sticker in the set for the correct option codes.
Important: after having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
back to
div. table
overview.
2. Technical Specifications, Diversity, and
2
C
Hide quick links:
Advertisement
Table of Contents
