Une F Ilter Equires The Optional; Rf Μ T Uning It ) - Yaesu FT dx 1200 Operating Manual

µ-t F
une
The RF µTuning Kit provides ultra-sharp RF selectivity for the front end of the transceiver. Very high Q is made pos-
sible by the narrow-band design. Three RF µTuning Kits are available. The MTU-160 covers the 1.8 MHz band. The
MTU-80/40 covers the 3.5 and 7 MHz bands. The MTU-30/20 covers 10.1 and 14 MHz bands.
When any (or all) of the three optional units are connected, they will be automatically adjusted to center on your operat-
ing frequency.
The narrow bandwidth is especially useful on the low bands, when many strong signals are being received via NVIS
propagation (Near Vertical-Incidence Signals) within a narrow bandwidth. The added protection for the RF stage is es-
pecially helpful in preventing IMD and blocking.
µ-Tune Operation
1. Press and hold in the [ MHz/µT ] button for one sec-
ond to activate the µ-Tune filter. The "µ-Tune" will
appear on the TFT display. The [ VFO-B/CLAR ]
knob works as the µ-TUNING knob.
A :
dvice
 The µ-Tune circuit will automatically align itself
to the operating frequency.
 Remember that µ-Tune only operates on the 14
MHz and lower bands.
2. Rotate the [ VFO-B/CLAR ] knob to peak the re-
sponse (background noise) or reduce interference.
A :
dvice
 You may observe the relative peak point of the
µ-Tune filter in the Tuning Offset Indicator on
the display, while tuning the [ VFO-B/CLAR ]
knob.
 The amount of change in the center frequency
of the µ-Tune filter, when rotating the [ VFO-
B/CLAR ] knob, can be configured using Menu
item "046 uTUNE DIAL STEP".
 If the μ-Tune filter has been manually adjusted
away from the center frequency, you may press
the [ CLEAR ] button to re-center the filter re-
sponse on the current operating frequency.
3. Press and hold in the [ MHz/µT ] button for one sec-
ond to disengage the µ-Tune filter
A :
dvice
Alternate presses of the [ MHz/µT ] button will switch
the µ-Tune filter between on or off.
A :
dvice
 You may change the indication of the Tuning Offset
Indicator to display the µ-Tune filter continuously
while the µ-Tune filter is activated. This is Menu
item "011 BAR DISPLAY SELECT". See "Changing
the Tuning Offset Indicator" on the next page for de-
tails of the setting.
 The µ-Tune filters are the most advanced, selective
RF preselector filters ever incorporated into an Ama-
teur Radio transceiver. The RF selectivity provided
FT 1200 O
DX peraTing
i
nterference
( r
ilter equireS the optionAl
M
anual
r
rF µ t
uning
t o
uning FFSet
by µ-Tune can be of tremendous value in ensur-
ing quiet, intermod-free reception even in the most
crowded bands on a contest weekend. The µ-Tune
filters provide RF selectivity on the order of a few
dozen kHz at -6 dB, at the expense of a few dB of
system gain on bands where noise figure is seldom
an issue. You will notice that the S-meter deflection,
when µ-Tune is engaged, is slightly less than when
it is out of the circuit; this is normal. If your antenna
system gain is so low that you cannot hear the band
noise when µ-Tune is engaged (highly unlikely), just
switch it out, to eliminate the slight insertion loss.
ejection
)
k
it
[ MHz/µT ] Button
[ VFO-B/CLAR ] Button
i
ndicAtor
Page 47