Stage 4; Installing The Switcher Mounting System And The Pvs 405D - Extron electronics PVS 405D Installation Manual

Polevault digital switcher systems
Hide thumbs Also See for PVS 405D:
Table of Contents

Advertisement

Stage 4:

Installing the Switcher
Mounting System and
the PVS 405D
Stage 4 Involves installing the switcher mounting system and the PVS 405D Digital Switcher.
This stage is divided into four sections based on the system type. Each system mounts the PVS 405D
switcher and associated power supply using a specific mounting kit.
A. PoleVault System (using the PMK 560 Pole Mount Kit)
B. WallVault Wall Mount System (using the WMK 160 Wall Mount Kit)
C. WallVault Short Throw System (using the USFM 100 Short Throw Wall Mount Kit)
D. PlenumVault System (using the PVM 220 PlenumVault Mount Kit)
The PVS 405D Digital Switcher
Lineout
Output
INPUTS
OUTPUT
1/2
3/4
HDMI
POWER
SIG
LINK
SIG
LINK
12V
3A MAX
PVT IN
PVT IN
HDMI
Power Supply
Connector
Output
HDMI/RGB Video and Audio
Inputs (1-4) from
PVT SW HDMI RGB D
Where it goes: PVS 405D and power supply install into a mounting
enclosure.
What it does: Receives input video and audio signals from AV source
input wall plates. Outputs and switches the video and
audio signals to a display device (such as a projector or
flat screen display) and ceiling speakers.
For installation of the PMK 560 for the PoleVault system, start at page 40.
For installation of the WMK 160 for the WallVault Wall Mount system, start at page 44.
For installation of the USFM 100 for the WallVault Short Throw system, start at page 47.
For installation of the PVM 220 for the PlenumVault system, start at page 52.
NOTES:
The installation must conform to national and local building and electrical codes, and UL requirements.
See the device user guide for details.
The included power supply MUST NOT be installed in wall cavities or similar locations.
Unless installing the PVM 220 (for the PlenumVault System only) the power supply MUST NOT be
installed above the suspended ceiling.
PoleVault Digital Systems • Installation — Stage 4 (Mounting System Kit and PVS 405D)
.
Paging Sensor
Port
PVS 405D
AUDIO OUT
PAGING
SENSOR
L
R
VOICELIFT
+V
INPUT 5
AUX
L
R
VoiceLift
Aux Audio
Input 5
Receiver Port
Aux
Input
Speaker
Output
AMPLIFIED AUDIO OUT
DO NOT
L
R
GROUND
OR SHORT
4/8
SPEAKER
OUTPUTS
OVER PVT
REMOTE
IR
RS-232
S G
Tx Rx
G
RS-232
Control Port
IR Control
Input
3-Port 10/100
Ethernet Switch
LAN 1
LAN 2
LAN 3
Rear View
N
3
LA
2
LA
N
1
N
LA
T
O U
D IO
R
A U
FI ED
L
P LI
A M
T
NO
DO
ND
T
4/8
GR
OU
OR
SH
KE
R
OR
EA
S
SP
TP
UT
O TE
OU
R EM
-2 32
P VT
RS
R
O VE
IR
G
Rx
Tx
D
G
0 5
S
S 4
P V
G
G IN
R
PA
N SO
IF T
O U
T
EL
SE
IC
D IO
VO
A U
R
+V
U T
L
TP
O U
A U
X
T 5
P U
P U
TS
M I
IN
R
H D
IN
L
3 /4
K
LIN
SI G
1 /2
K
LIN
SI G
IN
P VT
W ER
PO
V
IN
12
M AX
P VT
3A
39

Advertisement

Table of Contents
loading

Table of Contents