Adjust The Volume; Selecting The Digital Decode Mode - JVC XV-NK58SL Instructions Manual

Basic operations
DIMMER SETTING ADJUST SURROUND
DVD MULTI DVD
STANDBY / ON STANDBY
HOME THEATER RECEIVER
AUDIO
OPEN/CLOSE
DVD VCR DBS TV
DVD VCR DBS TV
DVD MULTI FM/AM TV/VIDEO MUTING
TV VOL CHANNEL VOLUME
DVD
AUDIO/TV
/VCR/DBS
TUNING FM MODE TUNING
MEMORY
TOP MENU MENU
ENTER
ON
CHOICE
SCREEN
AUDIO SUBTITLE TITLE/GROUP RETURN
ZOOM BASS TREBLE
1 2 3
PROGRESSIVE BASS TREBLE
VFP 4 5 6
7 8 9
ANGLE TV RETURN 100 +
10 0 +10
REPEAT
3D
DIMMER SLEEP ANALOG/DIGITAL CANCEL
INPUT
SMART S. SETUP BASS BOOST A.POSITION
TONE
SURROUND
TEST EFFECT DECODE
SUBWFR CENTER L SURR R
3

Adjust the volume

To increase the volume, turn MASTER VOLUME
control clockwise (or press VOLUME + on the
remote control).
To decrease the volume, turn MASTER VOLUME
control counterclockwise (or press VOLUME – on
the remote control).
CAUTION:
Always set the volume to the minimum before starting any sources.
If the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
NOTE
The volume level can be adjusted within the range of "0" (minimum) to
"50" (maximum).
Listening with headphones
Connect a pair of headphones to the PHONES jack on the front
panel . This cancels the Surround mode currently selected,
deactivates speakers, and activates the HEADPHONE mode.
The HP (headphone) indicator lights up on the display.
• Disconnecting a pair of headphone from the PHONES jack cancels
the HEADPHONE mode and activates the speakers.
12
SOURCE SELECTOR
/ MULTI JOG
SET / TUNER PRESET
DBS VCR TV FM / AM
When operating the receiver
using the remote control,
always set the mode selector
to AUDIO/TV/VCR/DBS.
HEADPHONE mode
When using the headphones, the following signal is output
MASTER VOLUME
PHONES
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signal is
output directly from the left and right headphones.
— For multi-channel sources, the front left and right, center and
surround channel signal is down-mixed and then output from
the headphones without missing bass element.
You can enjoy multi-channel sound source using the
headphones.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before removing headphones, as high volume may output from the
speakers.

Selecting the digital decode mode

If the following symptoms occur while playing Dolby Digital or DTS
Digital Surround software with "DGTL AUTO" selected (see page 11),
follow the procedure below:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching for or skipping chapters or tracks.
From the remote control ONLY:
1
Press ANALOG/DIGITAL INPUT to select "DGTL
AUTO."
2
Press DECODE to select "DGTL D.D." or "DGTL
DTS."
• Each time you press the button, the digital decode mode
changes as follows:
L C R
SUBWFR LFE
DOLBY D
LS RS
DGTL AUTO
• To play back software encoded with Dolby Digital, select "DGTL
D.D."
• To play back software encoded with DTS Digital Surround,
select "DGTL DTS."
NOTE
When you turn off the power or select another source, "DGTL DTS" or
"DGTL D.D." is canceled and the digital decode mode is automatically
reset to "DGTL AUTO."
DGTL D.D.
DGTL DTS
VOL