Page 2
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben protección aislante, que puedan encontrarse dentro use. In no event will Extron Electronics be liable for direct, indirect, or consequential instalar en lugares donde no sean pisados ni apretados por objetos que se puedan de la caja o alojamiento del producto, y que puedan apoyar sobre ellos.
Configuring the On and Off buttons........3-13 Step 7: Configure the Control Modules Using the Auto Fill Feature ................ 3-14 Step 8: Create a Display Shutdown Schedule ....3-16 MLC 226 IP Series MediaLink Controllers • Table of Contents...
Accessing GlobalViewer ............3-23 Chapter One Introducton About.this.Manual About.the.MLC.226.IP.MediaLink ™ .Controllers About.Global.Configurator System.Requirements Installing.the.Software Updating.Firmware 68-1288-01.A 07.06 All trademarks mentioned in this manual are the properties of their respective owners. MLC 226 IP Series MediaLink Controllers • Table of Contents...
Page 6
Audio About the MLC 226 IP MedaLnk Controllers Document Camera The Extron MLC 226 IP Series MediaLink Controllers are A typical application for an MLC 226 IP controller capable of controlling a projector and various other items such as lights, a projector lift, or a screen motor. Although this setup...
Engineer to determine if your Extron product also requires a firmware update. For more information regarding how to update the firmware, refer to Appendix B in the MLC 226 Series User's Manual. MLC 226 IP Series MediaLink Controllers • Introduction...
Pin 5 Computer's signal ground Sleeve has one pin (pin 1) designated for digital input/output. Wiring for the TRS RS-232 cable option MLC 226 IP Series MediaLink Controllers • Hardware Setup MLC 226 IP Series MediaLink Controllers • Hardware Setup...
Page 9
Set (SIS) commands. For a list of commands and additional information, refer to the MLC 226 Series User's Manual. MLC 226 IP Series MediaLink Controllers • Hardware Setup MLC 226 IP Series MediaLink Controllers • Hardware Setup...
Page 10
IR or RS-232 control. Relay On • off — relay opens and stays open until otherwise instructed Relay Off MLC 226 IP Series MediaLink Controllers • Hardware Setup MLC 226 IP Series MediaLink Controllers • Hardware Setup...
Use a straight‑through cable for connection to a switch, hub, or router. • Use a crossover cable for connection directly to a PC. MLC 226 IP Series MediaLink Controllers • Hardware Setup MLC 226 IP Series MediaLink Controllers • Hardware Setup...
Buttons MLC 226 IP Right Side The MLC 226 IP Series controllers have backlit buttons. The button caps are removable so the button labels can be changed. Display On/Off buttons — After they have been configured, press the On button to turn the display device on, and press the Off button to power it off.
MLC 226 IP MLC 226 IP MLC 226 IP 2"–12" (4–30 cm) 30 feet max. IR 402 IR control and learning MLC 226 IP Series MediaLink Controllers • Hardware Setup 2-12 MLC 226 IP Series MediaLink Controllers • Hardware Setup 2-13...
MLC 226 IP Hardware Setup, cont’d MLC 226 IP MediaLink Controllers Chapter Three MLC 226 IP Software Setup Step.1:.Download.Device.Drivers Step.2:.Create.a.New.Project Step.3:.Add.an.MLC.226.IP.Controller.and.Define.its.Location. Step.4:.Define.Email.Settings. Step.5:.Add.Serial.and.IR.Devices Step.6:.Configure.the.Front.Panel.Buttons. . Step.7:.Configure.the.Control.Modules.Using.the.Auto.Fill.Feature Step.8:.Create.a.Display.Shutdown.Schedule Step.9:.Create.a.Display.Lamp.Hour.Warning.Email Step.10:.Create.a.Display.Disconnection.Email Step.11:.Build.and.Upload.a.Configuration MLC 226 IP Series MediaLink Controllers • Hardware Setup 2-14...
Page 15
OK button. The GC 2 Start Options dialog reappears. MLC 226 Series User's Manual or the GC Help file accessed through the GC software. MLC 226 IP Series MediaLink Controllers • Software Setup MLC 226 IP Series MediaLink Controllers • Software Setup...
By default, there is no password set on the controller. MLC 226 IP Series MediaLink Controllers • Software Setup MLC 226 IP Series MediaLink Controllers • Software Setup...
Page 17
This action automatically populates the Name, Subject, and Body fields for the action, but these fields can be altered, if needed. MLC 226 IP Series MediaLink Controllers • Software Setup MLC 226 IP Series MediaLink Controllers • Software Setup...
Notice that this action also populates the Driver Command and State Configuration field with predefined functions. These functions appear as buttons on your GlobalViewer Web page. MLC 226 IP Series MediaLink Controllers • Software Setup MLC 226 IP Series MediaLink Controllers • Software Setup...
Page 19
Notice that this action also populates the IR Driver Function(s) field with predefined functions. To view these IR driver functions as buttons on your MLC 226 IP Series MediaLink Controllers • Software Setup 3-10 MLC 226 IP Series MediaLink Controllers • Software Setup...
DVD. You can change this to a different name, if desired, and set the tool tip, repeat rate, and button mode, if applicable. MLC 226 IP Series MediaLink Controllers • Software Setup 3-12 MLC 226 IP Series MediaLink Controllers • Software Setup...
IRCM-DV+), select Input 2, as illustrated on the following page. This associates the DVD functions whenever Input 2 is selected. MLC 226 IP Series MediaLink Controllers • Software Setup 3-14 MLC 226 IP Series MediaLink Controllers • Software Setup...
Select the action, Power Control Off from Available Options window, and click Apply Action. Click Done. The dialog box closes. Scheduled Actions Wizard MLC 226 IP Series MediaLink Controllers • Software Setup 3-16 MLC 226 IP Series MediaLink Controllers • Software Setup 3-17...
Page 23
Display lamp hour email notification Click Done. The dialog box closes. Monitored Conditions Wizard dialog MLC 226 IP Series MediaLink Controllers • Software Setup 3-18 MLC 226 IP Series MediaLink Controllers • Software Setup 3-19...
An activity bar appears, indicating that the build is progressing. The Upload Manager dialog appears when the build is complete. MLC 226 IP Series MediaLink Controllers • Software Setup 3-20 MLC 226 IP Series MediaLink Controllers • Software Setup 3-21...
Page 25
Right-click the MLC 226 IP controller icon in the IP Link ® tree and select Open GlobalViewer Webpage. The Upload Manager window before file upload GlobalViewer main page MLC 226 IP Series MediaLink Controllers • Software Setup 3-22 MLC 226 IP Series MediaLink Controllers • Software Setup 3-23...