Taking The Unit Into Operation With Coating Material; Spraying Technology; Tempspray (Accessory); Handling The High-Pressure Hose - WAGNER Super Finish 7000 Operating Manual

Super Finish 7000
5

SPRAyING tecHNOlOGy

Move the spray gun evenly during the spraying process. If this
is not observed, an irregular spraying appearance will be the
result. Carry out the movement with the arm, not with the
wrist. A parallel distance of approx. 30 cm between the tip and
the surface to be coated should always be observed. The lat-
eral limitation of the spray fan should not to be too distinct.
The edge of spraying should be gradual to facilitate overlap-
ping of the next coat. The spray gun should always be held at
an angle of 90° to the surface to be coated. A spray fan aimed
obliquely at the surface to be coated leads to an unwanted
spray cloud.
Depending on the material, the use of a
smaller nozzle size or fewer guns can impro-
ve the spray pattern when using multiple-
gun operation.
To achieve perfect surfaces at varnishing works, special acces-
sories are available at Wagner, e.g. FineFinish tips or an AirCoat
gun set. Your Wagner dealer will advise you.
5.1

teMPSPRAy (AcceSSORy)

The paint material is heated to the required temperature uni-
formly by an electric heating element, which is located inside
the hose (regulated from 20°C to 60°C).
Advantages:
• Constant paint temperature even at low outside tempera-
tures
• Considerably better working of high viscosity coating ma-
terials
• Increase application efficiency
• Savings in solvents due to reduction in viscosity
tempSpray H 326 (ideal for
dispersions/materials with
high viscosity)
Order no. 2311661
Scope of delivery:
Basic unit 1/4" incl. Hose reel,
heated hose DN10, 30m, hose
1/4" DN4, 1m
6
HANdlING tHe HIGH-PReSSuRe
HOSe
The high-pressure hose is to be handled with care. Avoid sharp
bending or kinking. The smallest bending radius amounts to
about 20 cm.
Do not drive over the high-pressure hose. Protect against
sharp objects and edges.
sprayIng technIque / handlIng the hIgh-pressure hose / InterruptIon of work
6.1
The unit is equipped with a high-pressure hose specially suit-
ed for diaphragm pumps.
7
1. Turn pressure regulating knob three revolutions to the
2
3. Switch off the unit
4. Pull the trigger guard on all spray guns in order to safe-
5. Secure the spray gun, refer to the operating manual of the
6. Remove tip from tip holder and store the tip in a small ves-
7. Leave the suction system immersed in the coating mate-
8. Cover the material container in order to prevent the paint
Danger of injury through leaking high-
pressure hose. Replace any damaged high-
pressure hose immediately.
Never repair defective high-pressure hoses
yourself!
When using the high-pressure hose while
working on scaffolding, it is best to always
guide the hose along the outside of the scaf-
folding.

HIGH-PReSSuRe HOSe

Only use WAGNER original-high-pressure
hoses with internal heating in order to ensure
functionality, safety and durability.
Longer hoses (30 m is optimal) reduce vibra-
tions.

INteRRuPtION OF WORk

left.
Open relief valve (2)
valve position (circulation)
ly relieve the pressure of high-pressure hoses and spray
guns.
spray gun.
sel with suitable cleaning agent.
rial or immerse it in the corresponding cleaning agent.
The suction filter and unit should not dry out.
from drying.
When using quick-drying or two-component
coating substances, always flush the device
through with a suitable cleaning agent with-
in the processing time, as otherwise it will be
difficult to clean.
GB
43