Table of Contents
Advertisement
SYSTEM
System Type selection
The T14SG is for 2.4GHz only. The system
can be changed from among 5 choices: FASSTest
1 4 C H , FA S S Te s t 1 2 C H , FA S S T M U LT I ,
FASST 7CH, S-FHSS. It is FASSTest14CH and
FASSTest12CH which can be chosen by R7008SB
set. The method of selection is to the next page.
*If you change the System Type, other model data is not
reset.
*If a system type is changed in Helicopter mode, the
transmitter will offer two selections:
[Yes] : Selection sets the channel order suitable for System
Type. (We recommend here. )
[No] : The present channel order is maintained.
*After any change, remember to test the model and should
fully check servo direction and a motion.
*Analog servos cannot be used with the R7008SB in the
6HOHFW >6<67(0@ LQ WKH /LQNDJH PHQX DQG DFFHVV
WKH VHWXS VFUHHQ VKRZQ EHORZ E\ WRXFKLQJ WKH
571 EXWWRQ
6HOHFW WKH IXQFWLRQ QDPH
DQG UHWXUQ WR WKH /LQNDJH
PHQX E\ WRXFKLQJ WKH
R T N E X W W R Q
2 U W K H
H O M E / E X I T E X W W R Q L V
SXVKHG
Area mode selection (Frequency range)
The T14SG transmitter has been designed to
function in many countries. If you will be utilizing
this transmitter in a country other than France,
please make sure that [AREA] is set to "G". If,
however, this transmitter will be utilized in France,
it must be set to "F" in order to comply with French
regulations.FASST mode selection
Receiver linking
The receiver will only be controlled (without
being affected by other transmitters) by the
transmitter it is linked to. When using a receiver
other than one purchased as a set, linking is
necessary.
Moreover, a re-link is required when a new
model is added by model selection, and the time of
system type change.
Linking method
6\VWHP PRGH VHWWLQJ 5HFHLYHU OLQN
FASSTest 12CH mode.
Dual receiver function (only FASSTest 14CH
mode)
Dual receivers can be linked with the T14SG.
Two receivers are recognized individually by ID
numbers. For example, in R7008SB, CH output
setting function is used, by setting the first as as
"1-8CH", and setting the second as "9-14CH", two
sets of receivers can be used as a set in the model,
allowing you 14 channels. If a Dual receiver
function is used, the following function can set up
individually.
Battery fail-safe voltage setup
Telemetry function ON/OFF
Sensor setup
Cases when linking is necessary:
:KHQ XVLQJ D UHFHLYHU RWKHU WKDQ WKH LQLWLDO VHWWLQJ
:KHQ WKH FRPPXQLFDWLRQ V\VWHP ZDV FKDQJHG
)$667HVW&+
:KHQ D QHZ PRGHO ZDV FUHDWHG E\ PRGHO
VHOHFWLRQ
Battery fail-safe voltage setup (only FASSTest
mode)
The voltage which battery fail-safe activates,
can be set when you link. (3.5-8.4V) The receiver
memorizes the setting as it was at link.
Suggested setting voltages are as follows.
‡ FHOOV 1L&G RU 1L0+ 1RUPDO Y
‡ FHOOV /L)H 1RUPDO Y
‡ FHOOV /L3R 1RUPDO Y
It is a rough reference value.
Since it changes with servos carried in the
condition and the model of a battery, please set to
your own model in a battery consumption current.
<SensorTouch™>
6FUROOLQJ
)$667HVW&+ HWF
a Y
a Y
<Functions of Linkage Menu>
0RYLQJ FXUVRU
6HOHFWLQJ PRGH
Y
73
Advertisement
Table of Contents
