Table of Contents
Advertisement
Setting method
$FWLYDWH WKH PRWRU VSHHG IXQFWLRQ
When using motor speed function, move the
FXUVRU WR WKH >,1+@ LWHP DQG WRXFK WKH 571
button to switch to the data input mode.
6HOHFW WKH >$&7@ E\ VFUROOLQJ WKH WRXFK VHQVRU
and touch the RTN button.
6LIWLQJ WKH ERXQGDU\ EHWZHHQ WKH UDQJHV
0RYH WKH FXUVRU WR WKH >63((' !@ LWHP DQG
touch the RTN button to switch to the data
input mode.
$GMXVW WKH ERXQGDU\ SRVLWLRQ E\ VFUROOLQJ WKH
touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to return to the cursor
mode.
2SHUDWLRQ VSHHG DGMXVWPHQW
0RYH WKH FXUVRU WR WKH >,1@ RQ WR RII RU >287@
RII WR RQ LWHP DQG WRXFK WKH 571 EXWWRQ WR
switch to the data input mode.
$GMXVW WKH RSHUDWLRQ VSHHG \RX ZDQW WR VHW
by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to return to the cursor
mode.
6HW5HVHW WKH RQH WLPH RSHUDWLRQ
0RYH WKH FXUVRU WR WKH >21( 7,0(@ LWHP DQG
touch the RTN button to switch to the data
input mode.
6HOHFW WKH >$&7@ E\ VFUROOLQJ WKH WRXFK VHQVRU
and touch the RTN button to set the one time
operation.
* When you want to reset one time operation, set the ACT/
INH item to [INH] and then reset it to [ON].
212)) GLUHFWLRQ
0RWRU IXQFWLRQ VZLWFK
current position
<Model Menu (Airplane/Glider Functions)>
6WDUW VZLWFK IXQFWLRQ
:KHQ DFWLYH WKH 67$57 6: DOORZV WKH
PRWRU
V VWDWH WR FKDQJH IURP 2)) WR 21 7KH
PRWRU LV 21 ZKHQ WKH PDLQ 6: DQG 67$57
6: DUH WXUQHG 21 VLPXOWDQHRXVO\ 7KH PRWRU
FKDQJHV WR 2)) RQO\ ZKHQ WKH PDLQ 6: LV
WXUQHG RII ,I 67$57 6: LV WXUQHG 2)) EXW WKH
main SW is still ON, the motor remains ON.
[START SW function example]
When the throttle (motor) stick is assigned as the "START SW",
and the low throttle position of the throttle curve is adjusted, the
motor starts operating with the initial stick movement. The motor
will not cease functionality even if the stick position is returned to
it's lowest setting.
7ULP HIIHFW LQYDOLG VHWWLQJ LQ PRWRU 2))
,I RQH RI WKH WULP OHYHUV LV DVVLJQHG WR WKH
Motor function, it is possible to turn the
motor off with the trim lever. To maintain
FRPSDWLELOLW\ DIWHU XSGDWLQJ WKH 76*6
WKH WULP VHWWLQJ LV DGMXVWHG WR WKH RQ SRVLWLRQ
+RZHYHU LW LV VXJJHVWHG WR UHWXUQ LW WR WKH RII
position accordingly in the programming of
the transmitter.
*Data Reset will return the trim setting to the off position.
6FUHHQ DW WKH WLPH RI WKH PRWRU 2)) VHWWLQJ
:KHQ WKH 02725 2)) VHWWLQJ LV KLJKOLJKWHG
you will note the presence of the small cursor
WKDW LQGLFDWHV WKH 02725 2)) SRVLWLRQ 7R
DGMXVW WKLV 02725 2)) SRVLWLRQ XVH WKH
throttle stick to move the cursor accordingly.
When satisfied with this position, press and
hold the RTN button on the transmitter.
*The larger cursor is used to indicate the output of the motor
FKDQQHO 7KLV FXUVRU UHÀHFWV DQ\ WKURWWOH FXUYHV DQG PRWRU
mixing which may be active.
7KURWWOH FXUYH EXWWRQ
:KHQ &859( EXWWRQ LV FKRVHQ D WKURWWOH
curve screen opens.
*When a throttle function is assigned to either channel, the
"CURVE" button is not displayed because a throttle curve
does not function as a motor curve.
143
Advertisement
Table of Contents
