Milnor 36026V5J, 36026V7J Service
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washer
  5. 36026V5J, 36026V7J
  6. Service

Milnor 36026V5J, 36026V7J Service

Hide thumbs Also See for 36026V5J, 36026V7J:
Table of Contents

Advertisement

Quick Links

Published Manual Number/ECN: MAP36VXXCE/2006145A
• Publishing System: TPAS
• Access date: 4/6/2006
• Document ECN's: Latest Available
Service—
36026V5J, 36026V7J/V7W
42026V6J/V6W
Washer-Extractors
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Milnor 36026V5J, 36026V7J

Summary of Contents for Milnor 36026V5J, 36026V7J

  • Page 1 Published Manual Number/ECN: MAP36VXXCE/2006145A • Publishing System: TPAS • Access date: 4/6/2006 • Document ECN's: Latest Available Service— 36026V5J, 36026V7J/V7W 42026V6J/V6W Washer-Extractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
  • Page 2 “Troubleshooting” chapter or section. See the table of contents. Trademarks of Pellerin Milnor Corporation The following, some of which may be used in this manual, are trademarks of Pellerin Milnor Corporation: ®...
  • Page 3 Avoiding Damage from Allied Remote Chemical Delivery Systems BIWUUI03/20030306 Safety Placard Use and Placement 36026V5J, 36021CPE, NSP & V5J BMP020109/2002145V Safety Placard Use and Placement ISO 36026V5J, 36021CPE, NSP & V5J BMP020110/2002145V Safety Placard Use and Placement 36026V7J/W & 42026V6J/W BMP020111/2002145V Safety Placard Use and Placement ISO 36026V7J/W &...
  • Page 4 Table of Contents, cont. Page Description Document/ECN Section 5: Control and Sensing Vibration Safety Switch Adjustments MSSMA408BE/9273BV Vibration Safety Switch BMP910038/2000302V Level Sensing BMP050027/2005171V Section 6: Chemical and Supply Devices Soap Chute Assembly BMP870042/2003276V Peristaltic Supply Assembly BMP000043/2001242V 5 Compartment Supply BMP860026/2000333V Flushing Manifold - 5 Compartment Supply BMP900019/2000455V...
  • Page 5 (including purchased components) without obligation to change any equipment previously supplied. ANY SALE OR FURNISHING OF ANY EQUIPMENT BY MILNOR IS MADE ONLY UPON THE EXPRESS UNDERSTANDING THAT MILNOR MAKES NO EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE.
  • Page 7 How to order repair parts Repair parts may be ordered either from the authorized dealer who sold you this machine, or directly from the MILNOR factory. In most cases, your dealer will have these parts in stock. When ordering parts, please be sure to give us the following information: 1.
  • Page 8 The owner/user must familiarize himself with the contents of all machine instruction manuals. The owner/user should direct any questions about these instructions to a Milnor® dealer or the Milnor® Service department.
  • Page 9 The Safety Guide and other machine manuals must be available at all times to the appropriate personnel. See the machine service manual for safety placard part numbers. Contact the Milnor Parts department for replacement placards or manuals. Maintenance —Ensure the machine is inspected and serviced in accordance with the norms of 1.5.
  • Page 10 Processing can cause solvent-containing goods to give off flammable vapors. • Do not use flammable solvents in processing. • Do not process goods containing flammable substances. Consult with your local fire department/public safety office and all insurance providers. PELLERIN MILNOR CORPORATION...
  • Page 11 This will over-speed the motor and pulleys and can cause them to rip apart, discharging metal fragments at high speed. • Stop the machine immediately if any of these conditions occur: • abnormal whining sound during extract • skidding sound as extract ends • clutches remain engaged or re-engage during extract PELLERIN MILNOR CORPORATION...
  • Page 12 Hazards include but are not limited to panic, burns, poisoning, suffocation, heat prostration, biological contamination, electrocution, and crushing. • Do not enter the cylinder until it has been thoroughly purged, flushed, drained, cooled, and immobilized. — End of BIUUUS27 — PELLERIN MILNOR CORPORATION...
  • Page 15 BMP010013/2002022V (Sheet 3 of 3) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Guards & Covers Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 17 BMP010034/2002103V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Guards and Covers Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 18: Warranty

    • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model ® and size upon request. Floor or foundation sizes shown on any Milnor...
  • Page 19 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain ® written confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
  • Page 20 7\_ccQbi_VDQW9\\ecdbQdY_^c± <B8DD@C604!"#$E 6Cdi\UACdi\U#&$"FCdi\U Q^THCdi\UGQcXUb5hdbQSd_bc Illustration Explanation Stop! Read the manual first for complete instructions before continuing. Do not jack the machine here. Do not lift the machine here. Use three point or four point lifting as determined by the lifting eyes furnished. Rig the load using lifting cables of sufficient size and length to ensure cables are not over-stressed.
  • Page 21 Illustration Explanation Do not start this machine until the packing materials, lifting brackets, etc. with this tag attached or behind this panel are removed. These materials are painted red. Safety stands or brackets (also painted red) may be provided with this machine. Do not discard safety stands or brackets Do not step or stand on this machine part.
  • Page 22 7\_ccQbi _V DQW 9\\ecdbQdY_^c± 6Cdi\U ACdi\U #&  $" FCdi\U Q^T HCdi\U GQcXUb5hdbQSd_bc Do not start this machine until the part with this tag is installed on the machine. Do not remove this component from the machine. Install the appropriate part here before operating the machine.
  • Page 23 =C9EEAD715" # $%F "  # During drain and extract, the cylinder must rotate counterclockwise when viewed from here (rear of machine). During drain and extract, the cylinder must rotate clockwise when viewed from here (front of machine). Do not pump grease here. Do not strike shell front of washer-extractors during fork lifting.
  • Page 24 7\_ccQbi _V DQW 9\\ecdbQdY_^c± 6Cdi\U ACdi\U #&  $" FCdi\U Q^T HCdi\U GQcXUb5hdbQSd_bc Make cold water connection here. Make hot water connection here. Make third (reuse) water connection here. Hold the connection side of the valve with a wrench when connecting plumbing.
  • Page 25 ® of such systems by the chemical supply company. Milnor washer-extractors and CBW batch washers (tunnels) are available with convenient inlets for such systems (see Figure 1). Most common of the types of systems currently used in commercial laundering operations are pumped chemical systems.
  • Page 26 CAUTION 1 : Equipment and Textile Damage Hazards—Chemicals leaked into the machine, particularly when it is idle can destroy machine components and textiles left in the machine. Pellerin Milnor Corporation accepts absolutely no responsibility for damage to its equipment or to textiles therein from abnormal contact with chemicals.
  • Page 27 Hence, any concentrated chemical that remains in the injection line between the pump and the machine is free to flow into the machine. Some examples of this are shown in Figure 3. PELLERIN MILNOR CORPORATION...
  • Page 28 PELLERIN MILNOR CORPORATION...
  • Page 29 CAUTION 2 : Injury and Damage Hazards—Chemicals leaking from a chemical system may be corrosive or toxic. Such chemicals can injure personnel and damage equipment. • Use care when connecting chemical lines. • Inspect regularly for leaks. — End of BIWUUI03 — PELLERIN MILNOR CORPORATION...
  • Page 31 BMP020109/2002145V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 33 BMP020110/2002145V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 35 BMP020111/2002145V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 37 BMP020112/2002145V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 39 Section Service and Maintenance...

  • Page 40: Preventive Maintenance

    • Permit only qualified maintenance personnel to perform these procedures. 36026V5J Main Bearing Maintenance 36026V5J main bearing housings are oil-filled and require periodic draining and refilling (see below). 42026V6J bearing housings are grease filled and require periodic greasing of seals and bearings (See “Lubrication Precautions”...
  • Page 41 1. Locate the seal and bearing grease fittings (Figure 8). 2. Place the machine in a wash step (see operating manual). 3. With the cylinder turning, grease the seals and bearings as called for in the Preventive Maintenance Checklist. PELLERIN MILNOR CORPORATION...

  • Page 42: Baldor Motor Maintenance

    Note 3: If motor manufacturer's instructions conflict with manual section MSSM0274AE, follow manufacturers instructions. Motors are warranted by the manufacturers, not by Milnor. Correcting Belt Slippage The drive train has a special belt tension sleeve, allowing additional tension to be applied to a worn, slipping belt to extend the drive belt life.
  • Page 43 Raising motor platform Motor mount shaft Belt tension sleeve and motor mount shaft Legend Motor mount shaft Belt tension sleeve Shaft collars Figure 2: Belt Tension Sleeve Over Motor Mount Figure 3: Assembled Sleeve Over Motor Shaft Shaft PELLERIN MILNOR CORPORATION...
  • Page 44 Preventive Maintenance Maintenance Points Figure 4: 30022C4x, 30022T5x, 36021C4E and Figure 5: 30022C4x, 30022T5x, 36026V5J Oil Drain and Water Leak-off 36021C4E and 36026V5J Oil Fill/Vent Hoses (use either hose for filling) Figure 6: Drive Train Pulleys and Figure 7: 30022C4x, 30022T5x, 30022V6J, 36021C4E...
  • Page 45 Figure 8: 42026V6J Grease Points Figure 9: Motor Grease Points if so equipped, (42026V6J shown) Figure 10: 42026V6J Rear Reinforcement Plate Figure 11: Inverter Maintenance Points Legend 36026V5J and 42026V6J Inverters (36026V5J shown) Vent — End of BIRQUM01 — PELLERIN MILNOR CORPORATION...
  • Page 46 0[XV]X]V"%P]S#!Egg<^c^a<^d]c?[PcTfXcW Document ....BIRQVM01 Specified Date ....20010822 cWT3aXeT?d[[Th As-of Date ....... 20010822 Access Date..... 20010822 Applicability......RQV Language Code....ENG01 The motors on 36 and 42Vxx machines rest on a spring tensioned motor mount plate. Any misalignment between this motor mount and the drive pulley results in excessive drive belt twist and stress, greatly reducing belt life.
  • Page 47 1\YW^Y^W #& Q^T $"Fhh =_d_b =_e^d @\QdU gYdX dXU 4bYfU @e\\Ui 7. The shims are made in a u-shape to fit around the bolt. Estimate the thickness needed and slip the appropriate number of shims around the bolt. 8. Tighten bolt and measure again with the contractors square. Repeat steps 7 and 8, adding or subtracting shims as required until the straight edge touches the motor top at all points (or as close as possible with the shims used).
  • Page 48 The specifications in this section apply to 1/4 inch and larger Unified National fine and coarse fasteners used on ® Milnor machines. This information is to be used only when torque specifications are not stated in the installation or service instructions.
  • Page 49 MSSM0101CE/9906AV (2 of 19) Ê A pplying Threadlocker NOTE: The following threadlocker information and ® illustrations are excerpts from the Loctite User’s Guide and are used with permission. For maximum strength, threadlocker must fill the thread voids completely, as shown in FIGURE 2. Organic or petro- leum solvent will remove excess uncured adhesive from joints.
  • Page 50 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (3 of 19) Ë R emoving Fasteners ® High strength threadlockers like Loctite 271 (or equivalent) may be weakened by heating to at least 500 F (260 C) as follows. 1. Apply localized heat to fastener as shown in FIGURE 5. 2.
  • Page 51 MSSM0101CE/9906AV (4 of 19) Ï A ll values in foot pounds and (Newton meters) Nomi- Grade Designation Zinc or If instructions call for : nal bolt and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare size Plated 222 or 1/4 - 28 SAE Grade 1 ASTM A307 (3.80)
  • Page 52 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (5 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc If instructions call for : bolt size and Standard orCadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 5/16 - 24 SAE Grade 1 10.4 ASTM A307...
  • Page 53 MSSM0101CE/9906AV (6 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 3/8 - 24 SAE Grade 1 10.2 12.2...
  • Page 54 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (7 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 7/16 - 20 SAE Grade 1 16.0 19.2...
  • Page 55 MSSM0101CE/9906AV (8 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Standard and Zinc or If instructions call for : bolt size Grade Designation Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1/2 - 20 SAE Grade 1 24.8 29.8...
  • Page 56 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (9 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 9/16 - 18 SAE Grade 1 35.3 42.4...
  • Page 57 MSSM0101CE/9906AV (10 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 5/8 - 18 SAE Grade 1 49.5 59.4...
  • Page 58 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (11 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 3/4 - 16 SAE Grade 1 86.5...
  • Page 59 MSSM0101CE/9906AV (12 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for: bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 7/8 - 14 SAE Grade 1 137.8 165.4...
  • Page 60 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (13 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1 - 12 SAE Grade 1 205.3...
  • Page 61 MSSM0101CE/9906AV (14 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1-1/8 • 7 SAE Grade 1 265.8 318.9 354.4...
  • Page 62 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (15 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1-1/4 •...
  • Page 63 MSSM0101CE/9906AV (16 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or If instructions call for : bolt size and Standard Cadmium Loctite Loctite Loctite Loctite Loctite Bare Plated 222 or 1-3/8 • 6 SAE Grade 1 491.1 589.4 654.8...
  • Page 64 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (17 of 19) Ï A ll values in foot pounds and (Newton meters) Nominal Grade Zinc or If instructions call for : bolt size Designation and Cadmium Loctite Loctite Loctite Loctite Loctite Bare Standard Plated 222 or 1-1/2 •...
  • Page 65 MSSM0101CE/9906AV (18 of 19) Ï O ther Fastener Torque Specifications Ï A ll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Brass Aluminum Stainless Steel Stainless Steel 2024 - T4 1/4 - 20 6.3 (8.54) 6.6 (8.95) 5.1 (6.91) 3.8 (5.15) 1/4 - 28...
  • Page 66 FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (19 of 19) Ï O ther Fastener Torque Specifications Ï A ll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Brass Aluminum Stainless Steel Stainless Steel 2024 - T4 7/8 - 9 194.0 (263.03) 202.5 (274.55) 158.8 (215.30) 124.6 (168.93)
  • Page 67 <BB<!&#04(&" 0E Most of the information in this document is taken from the Baldor Electric Company Instruction, Operation, and Maintenance Manual, and provides a means of more accurately determining motor lubrication requirements based on local conditions. Inspect, clean, and test motors at regular intervals— approximately every 500 operating hours or every three months, whichever comes first.
  • Page 68 21<4?B =?D?B =19>D5>1>35 =CC= "'$15)'#!1F"$ —The useful life of antifriction bearing grease can be estimated, based on service conditions, frame type, and motor rpm. An example of determining the correct lubrication interval is provided below. Ex: A fan motor, operating at an ambient temperature of 109 F (43 C) in a moderately corrosive atmosphere.
  • Page 69 21<4?B =?D?B =19>D5>1>35 =CC= "'$15)'#!1F#$ Table 3 — Recommended Lubrication Intervals at Standard Service Conditions NEMA (IEC) Rated Speed - RPM Frame Size 3600 1800 1200 Up to 215 (132) 5500 Hrs. 12000 Hrs. 18000 Hrs. 22000 Hrs. 254 to 286 (160 - 180) 3600 Hrs.
  • Page 70 21<4?B =?D?B =19>D5>1>35 =CC= "'$15)'#!1F$$ —Use Shell Dolium R (factory installed) or Chevron SRI greases for standard service conditions. The extreme and low temperature conditions are not normally encountered in the laundry. However, for extreme conditions, use Darmex 707 and for low temperature conditions, use Arrowshell 7.
  • Page 71 Section Drive Assemblies...
  • Page 76 BMP000008/2001036V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Motor Mount Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 77 Section Bearing Assemblies...
  • Page 81 BMP930001/2003276V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Bearing Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 87 Section Shell and Door Assemblies...
  • Page 95 Section Control and Sensing...

  • Page 96: Vibration Safety Switch

    Ê A djustments ® When the machine leaves Milnor , the actuator arm is tie-wrapped to prevent damage (except on 30015, 30020, and 30022 models). This tie wrap must be removed after the machine is set into position but before the machine is op- erated.
  • Page 97 that it has reset. In the released position the arm should rest lightly but definitely against the stop on the micro-switch case that prevents any further arm movement to the left. For machines with rigid mounted shells, where the machine is bolted to a very substantial foundation, very little machine movement will occur for a given degree of out-of-balance.

  • Page 100: Level Sensing

    BMP050027/2005171V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Level Sensing Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 101 Section Chemical and Supply Devices...

  • Page 104: Peristaltic Supply Assembly

    BMP000043/2001242V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Peristaltic Supply Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 106: Compartment Supply

    BMP860026/2000333V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—5 Compartment Supply Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 108 BMP900019/2000455V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Flushing Manifold Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 109 Section Water Piping Assemblies...

  • Page 114: Steam Inlet Assembly

    BMP010027/2002064V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Steam Inlet Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 116: Drain Valve Installation

    BMP010014/2002034V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Drain Valve Installation Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 118: Electric Drain Valve

    BMP920017/2002044V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—3” Electric Drain Valve Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

This manual is also suitable for:

36026v7j42026v6j36026v7j/v7w42026v6j/v6w36026v7w42026v6w

Table of Contents