General Safety Information; California Proposition; Spraying Precautions - Campbell Hausfeld FP202801 Operating Instructions And Parts Manual

Operating Instructions and Parts List

General Safety Information

CALIFORNIA PROPOSITION 65

This product or its
power cord may
contain chemicals, including lead,
known to the State of California to
cause cancer and birth defects or other
reproductive harm. Wash hands after
handling.
You can
create
dust when you cut, sand,
drill or grind materials
such as wood, paint, metal,
concrete, cement, or other masonry.
This dust often contains chemicals
known to cause cancer, birth defects,
or other reproductive harm. Wear
protective gear.
GENERAL SAFETY
Since the air compressor and other
components (material pump, spray
guns, filters, lubricators, hoses,
etc.) used, make up a high pressure
pumping system, the following safety
precautions must be observed at all
times:
1. Read all manuals
included with this
product carefully. Be
thoroughly familiar with
the controls and the proper use of
the equipment.
2. Follow all local electrical and safety
codes as well as in the United
States, the National Electrical Codes
(NEC) and Occupational Safety and
Health Act (OSHA).
3. Only persons well acquainted
with these rules of safe operation
should be allowed to use the
compressor.
4. Keep visitors away and NEVER
allow children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the
unit.
6. Do not stand on or use the unit as
a handhold.
7. Before each use, inspect
compressed air system and
electrical components for signs of
damage, deterioration, weakness
or leakage. Repair or replace
defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
www.chpower.com
equipment and controls can
cause electrical arcs that
will ignite a fl ammable gas
or vapor. Never operate or repair in or
near a fl ammable gas or vapor. Never
store fl ammable liquids or gases in the
vicinity of the compressor.
Compressor parts may
be hot even if the unit is
stopped.
9. Keep fingers away from a
running compressor; fast moving
and hot parts will cause injury and/
or burns.
10. If the equipment should start
to vibrate abnormally, STOP
the engine/motor and check
immediately for the cause.
Vibration is generally a warning of
trouble.
11. To reduce fire hazard, keep engine/
motor exterior free of oil, solvent,
or excessive grease.
with a setting no higher than 125 psi
MANUAL
MUST be installed in the tank for this
compressor. The ASME safety valve
must have suffi cient fl ow and pressure
ratings to protect the pressurized
components from bursting.
for maximum operating pressure.
Do not operate with pressure switch
or pilot valves set higher than the
maximum operating pressure.
12. Never attempt to adjust ASME
safety valve. Keep safety valve
free from paint and other
accumulations.
compressed air. Serious injury or death
could result.
to repair or modify a tank!
Welding, drilling or any
other modifi cation will
weaken the tank resulting in damage
from rupture or explosion. Always
replace worn, cracked or damaged
tanks.
2
Motors, 13. Tanks rust from moisture build-up,
electrical
which weakens the tank. Make
sure to drain tank regularly and
inspect periodically for unsafe
conditions such as rust formation
and corrosion.
14. Fast moving air will stir up dust
and debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.

SPRAYING PRECAUTIONS

fl ammable materials in
vicinity of open fl ame
or near ignition sources
including the compressor unit.
15. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
16. Use a face mask /
respirator when spraying
and spray in a well
ventilated area to
prevent health and fire hazards.
An ASME code
safety relief valve 17. Do not direct paint or other
sprayed material at the compressor.
Locate compressor as far away
from the spraying area as
possible to minimize overspray
accumulation on the compressor.
See compressor
18. When spraying or cleaning with
specifi cation decal
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
Never use plastic
(PVC) pipe for
Never
attempt
Drain liquid from
tank daily.
FP202801, FP202901
Do not
spray