JVC GR-DVL817 Instructions Manual page 63

Program
N I OUT MODE
1 – – – – : – – ~
2 ~
3 ~
4 ~
5 ~
6 ~
7 ~
8 ~
T I ME CODE – – : – –
TOTAL 0 0 : 00
Remote sensor
R.A.EDIT
ON/OFF
CANCEL
EDIT IN/OUT
EFFECT
FADE/WIPE
RM-V716U
(Provided with
GR-DVL817 only)
NOTES:
When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between
them.
If the search time for an in-point exceeds 5 minutes, the recording deck's Record-Standby mode will be
canceled and editing will not take place.
If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in
the edited version.
Since time codes register time only as accurately as seconds, the time code total time may not match the
total program time exactly.
Turning off the camcorder's power erases all registered Edit-In and Edit-Out points.
For GR-DVL817 Owners:
If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or
Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next
Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during
recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.
It is not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble
Editing using a DV cable.
Random Assemble
Editing Menu
REW
FF
PLAY
IN/OUT
ON/OFF
OR RM-V700U
(optional)
SELECT SCENES
4
Point the remote control at the camcorder's remote
sensor. Press PLAY (4) and then press R.A.EDIT ON/
OFF or ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
5
For GR-DVL817 Owners: If using a Fade/Wipe at the
beginning of the scene, press FADE/WIPE on the
remote control.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
6
At the beginning of the scene, press EDIT IN/OUT or
IN/OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT or IN/
OUT. The Edit-Out position appears in the Random
Assemble Editing Menu.
8
For GR-DVL817 Owners: If using a Fade/Wipe at the
end of the scene, press FADE/WIPE.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•If you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
•You cannot use a Picture Wipe/Dissolve at the end
of the last scene.
•When you use Fade/Wipe effects, that time is
included in the total time (this does not apply to
Picture Wipe/Dissolve).
9
For GR-DVL817 Owners: If using Playback Special
Effects, press EFFECT (
10
Repeat steps 6 through 9 to register additional scenes.
•To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
• For GR-DVL817 Owners: If you are not using Fade/
Wipe or Program AE with special effects, repeat
steps 6 and 7 only.
EN
1
pg. 59).
CONTINUED ON NEXT PAGE
63