Table of Contents
Advertisement
Note:
The cabling instructions given below reproduce the configuration shown previously.
However, this is not the only possible HA configuration. In addition, the instructions
assume that all physical ports and interfaces are set at their default settings. If you have
changed the port and interface configurations, the instructions below might not work
properly.
To cable two NetScreen-200 Series devices together for HA and connect them to the
network:
1.
(Optional) Install the NetScreen-200 Series devices in an equipment rack (see
"Equipment Rack Installation Guidelines" on page
2.
Make sure that all ON/OFF power supply switches are OFF.
3.
Connect the power cables to each NetScreen-200 power supply then connect
them to a power source.
Note:
connect each to a different power source, if possible. If one power source fails, the
other source might still be operative.
4.
If your device is a NetScreen-204, connect a 10/100 Base-T cable from the
ethernet4 on Device 1 to the ethernet4 port on Device 2.
or
If your device is a NetScreen-208, connect a 10/100 Base-T cable from the
ethernet8 on Device 1 to the ethernet8 port on Device 2.
Device 1
5.
On Device 1, connect a 10/100 Base-T cable from ethernet1 to the switch
labeled "Switch 3."
6.
On Device 1, connect a 10/100 Base-T cable from ethernet2 to the switch
labeled "DMZ."
7.
On Device 1, connect a 10/100 Base-T cable from ethernet3 to the switch
labeled "Layer 3 switch 1."
Device 2
8.
On Device 2, connect a 10/100 Base-T cable from ethernet1 to the switch
labeled "Switch 4."
9.
On Device 2, connect a 10/100 Base-T cable from ethernet2 to the switch
labeled "DMZ."
10.
On Device 2, connect a 10/100 Base-T cable from ethernet3 to the switch
labeled "Layer 3 switch 2."
NetScreen-200 Series
Whenever you deploy two NetScreen-200 Series devices in an HA cluster,
Establishing an HA Connection Between Devices
10).
21
Advertisement
Table of Contents
Related Manuals for Juniper 200 Series
Related Products for Juniper 200 Series
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper SSG 20-WLAN
- Juniper Day One+
- Juniper EX 3200