Heat & Glo LUX36 Owner's Manual page 25

C
V
B
J
B
V
D
V
V
= VENT TERMINAL
A = 12 inches.................clearances above grade, veranda,
B = 12 inches.................clearance to window or door that may
C = 18 inches.................clearance below an unventilated/
= 18 inches .................clearance below an unventilated/ven-
= 42 inches .................clearance below a vinyl soffit with
= 42 inches .................clearance below a vinyl soffi t with vinyl
D = 6 inches...................clearance to outside corner
E = 6 inches...................clearance to inside corner
F = 3 ft. (Canada) ..........not to be installed above a gas me-
G = 3 ft ...........................clearance to gas service regulator vent
H = 12 inches.................clearance to non-mechanical (unpow-
i = 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
All mechanical air intakes within 10 feet of a termination cap must
be a minimum of 3 feet below termination.
J = 7 ft. ......................... On public property: clearance above
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings and
serves both dwellings.
K = 6 inches................. clearance from sides of electrical
L = 12 inches................ clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
M = 18 inches ....................clearance under veranda, porch, deck,
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the fl oor.
Figure 6.3 Minimum Clearances for Termination
F
B
V
G
M
V
A
X
= AIR SUPPLY INLET
porch, deck or balcony
be opened, or to permanently closed
window
ventilated soffi t with non-vinyl siding
tilated soffi t with vinyl siding. Requires
a vinyl protector kit (VPK-DV)
non-vinyl siding
siding. Requires a vinyl protector kit
(VPK-DV)
ter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
outlet
ered) air supply inlet, combustion air
inlet or direct-vent termination
air supply inlet
paved sidewalk or a paved driveway.
service
balcony or overhang
Heat & Glo • LUX36, LUX42 • 2287-900
H or i
V
X
H
V V
H
V
A
= AREA WHERE TERMINAL IS NOT PERMITTED
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N = 6 inches ........non-vinyl sidewalls
12 inches ......vinyl sidewalls
O = 18 inches .......clearance below an unventilated/ventilated soffi t
= 18 inches ......clearance below an unventilated/ventilated soffi t
= 42 inches ......clearance below a vinyl soffi t with non-vinyl siding
= 42 inches ......clearance below a vinyl soffi t with vinyl siding.
P = 8 ft.
1 cap
2 caps
3 caps
4 caps
Q = # termination caps x 3
MIN
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffi c areas or where people
may pass or gather (sidewalk, deck, patio,
shields available. Contact your dealer.
• Local codes or regulations may require different
clearances.
• Vent system termination is NOT permitted in screened
porches.
• Vent system termination is permitted in porch areas with
two or more sides open.
• Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
• Vinyl protection kits are required for use with vinyl siding.
• 2287-900 Rev. J Rev. J • 6/13
O
P
R
Q
K
Electrical
V
Service
with non-vinyl siding
with vinyl siding. Requires a vinyl protec-
tor kit (VPK-DV)
Requires a vinyl protector kit (VPK-DV)
Q R
MIN
3 feet 2 x Q
6 feet 1 x Q
9 feet 2/3 x Q
12 feet 1/2 x Q
R = (2 / # termination caps) x Q
MAX
etc.). Listed cap
N
V
L
K
V
C
V
MAX
ACTUAL
ACTUAL
ACTUAL
ACTUAL
ACTUAL
25