Optional Remote Control; Wall Thermostat; Remote Control - Jøtul GI 450 DV Katahdin Installation And Operation Instructions Manual

BK
BK
MANUAL
OFF
BU
AUTO
SWITCH
SNAPSTAT
Figure 19. Blower Wiring Diagram - GI 450 Katahdin

Wall Thermostat

Use only a 75 a 75 a 75 a 75 a 750 milliv 0 milliv 0 milliv 0 milliv 0 millivolt
thermosta thermostat t t t t . The thermostat should be placed in the thermosta
thermosta thermosta
same room as the heater, typically 5' off the floor. Avoid
drafty areas or any area that may affect the accuracy of
the thermostat.
The thermostat should be connected to the
Katahdin using a minimum of 16 gauge wire with a
maximum length of 35 feet of wire.
Connect the two thermostat wire leads to the two
lower terminals on the terminal block located to the
right of the ON/OFF/TSTAT switch. Do not overtighten
the connections. IT IS NOT NECESSARY TO DISCONNECT
ANY OTHER WIRES. See Figure 20.
For the thermostat to function, the ON/OFF/T-STAT
switch must be in the T-STAT position, and the pilot light
must be running, as it is the power source for the
thermostat.
At the thermostat, the two wires should be con-
nected to the two connections screws on the thermo-
stat base plate per the manufacturer's instructions.
THERMOPILE
TH
TP
TH
TP
VALVE
TERMINAL
BLOCK
Figure 20. Wiring diagram / GI450 DV Katahdin
POWER
SUPPLY
GN
WH
GY
BK BK
BLOWER
BK
RHEOSTAT
olt olt olt DC olt DC DC DC DC tw tw tw two-wir tw o-wire cir o-wir o-wir o-wir e circuit e cir e cir e cir cuit cuit cuit cuit
ROCKER
SWITCH
ON
OFF
STAT
OPTIONAL
THERMOSTAT
or
REMOTE
CONTROL

Optional Remote Control

#129706
The optional Jøtul remote can be installed on the
Katahdin gas insert. Using the wires supplied with
the remote, it is best to wire the remote directly to
the gas control valve of the insert.
Connect one receiver lead to the terminal la-
belled TH. Connect the other receiver lead to the
terminal labeled TH/TP. DO NOT DISCONNECT ANY
OTHER WIRES FROM THE VALVE, AND DO NOT OVER
TIGHTEN TERMINAL SCREWS.
Jøtul r Jøtul rec ec ec ec ecommends Jøtul r ommends ommends
Jøtul r Jøtul r ommends ommends the use o
R R R R R emote R emote R emote Rec ec ec ec eceiv emote R emote R eiver Hea eiv eiv eiv er Heat t t t t Shield (# 129 er Hea er Hea er Hea
the receiver under the firebox. The best location for
the receiver is just below the air intake port toward
the back of the unit.
Place Receiver Here
Figure 21. Remote Receiver position.
CAUTION:
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN
SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE
IMPROPER AND DANGEROUS OPERATION. ALWAYS VERIFY
PROPER OPERATION AFTER SERVICING THE APPLIANCE.
ATTENTION:
AU MOMENT DE L'ENTRETIENDES COMMANDES,
ETIQUETEZ TOUS LES FILS AVANT LE DEBRANCHEMENT.
DES ERREURS DE CABLAGE PEUVENT ENTRAIUN FONC-
TIONNEMENT INADEQUAT ET DAGEREUX.
the use o the use of f f f f the optional the use o the optional the optional
the use o the optional the optional
Shield (# 129 Shield (# 1297 7 7 7 7 08) Shield (# 129 Shield (# 129 08) to protect 08) 08) 08)
Air
Intake
Port
17