Related Manuals for Intel IXDP465
Summary of Contents for Intel IXDP465
- Page 1 ® Intel IXDP465 Development Platform Quick Start Guide May 2005 Order Number: 305825, Revision: 002 May 2005...
- Page 2 Intel products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Intel may make changes to specifications and product descriptions at any time, without notice.
-
Page 3: Table Of Contents
Preparing the Platform for Initial Use ... 21 10.0 Starting the Platform ... 21 11.0 Operating the Platform... 22 12.0 Technical Support ... 22 Figures Photo of IXDP465 Development Platform Setup for Quick Start Operation ... 8 ® Intel IXDP465 Development Platform Switch Locations ... 11 ®... -
Page 4: Revision History
• Added references to Intel Platform Specification Update. • Added detail to procedure in • Added Section 5.1, “Emulation with the Intel Development Platform” on page • Clarified default settings for J127 and J128 in (SCR 4280) • Added info about updating flash memory to (SCR 4281) •... -
Page 5: Purpose
Intel Platform. Before the IXDP465 development platform is powered up for the first time, it is very important to first become familiar with the platform. Therefore, required information for powering up the platform for first time use. These sections provide the following information: •... -
Page 6: Known Issues
® Intel IXDP465 Development Platform—Quick Start Guide Table 1. Reference Documents (Sheet 2 of 2) ® Intel IXP4XX Product Line of Network Processors Specification Update ® Intel IXP45X and Intel Processors Datasheet ® Intel IXP45X and Intel Processors Developer’s Manual ®... -
Page 7: Intel ® Ixdp465 Development Platform Overview
Intel Figure 1 should also be referenced while preparing the platform for initial use per use as a visual aid to validating proper setup of the IXDP465 development platform for Quick Start operation. Intel Quick Start Guide—Intel... -
Page 8: Emulation With The Intel ® Ixdp465 Development Platform
IXP45X and Intel development platform is shipped with a fully-featured Intel at 533 MHz, the platform can also be used to develop products that require either an Intel Network Processor or an Intel the IXP465 processor’s features, therefore software can be used to disable certain features on the IXP465 to emulate the IXP460 and IXP455 processors. -
Page 9: Default Switch Settings
This section describes the factory default settings of all platform switches, to ensure they were not accidentally changed during transport, or repositioned by a previous user of the platform. The IXDP465 development platform has all switches located on the top-side of the entire assembly. Figure 2 on page 11 one for GPIO LED Switches and one for Expansion Bus Address Strap Switches. -
Page 10: Intel ® Ixdp465 Development Platform Switch Descriptions And Default Settings
® Intel IXDP465 Development Platform—Quick Start Guide ® Table 3. Intel IXDP465 Development Platform Switch Descriptions and Default Settings Board Location (See Figure 2) GPIO LED Switches GPIO LED Switches Expansion Bus Address Strap Switches Expansion Bus Address Strap Switches... -
Page 11: Intel ® Ixdp465 Development Platform Switch Locations
® Figure 2. Intel IXDP465 Development Platform Switch Locations R145 GPIO 15 GPIO 13 GPIO 11 GPIO 9 GPIO 7 GPIO 5 GPIO 3 GPIO 1 Intel Quick Start Guide—Intel Expansion Bus Address trap witches GPIO LED witches R148 ®... -
Page 12: Default Jumper Settings
IXDP465 Development Platform—Quick Start Guide Default Jumper Settings This section defines the factory default settings for all IXDP465 development platform jumpers, to ensure they were not accidentally changed during transport, or repositioned by a previous user of the platform. The jumper settings are discussed in the following sections: ®... - Page 13 ® Table 4. Intel IXDP465 Baseboard Jumper Descriptions and Default Settings (Sheet 2 of 2) Board Location (See Figure 3) MII/SMII/UTOPIA: ETH B MII/SMII/UTOPIA: ETH C MII/SMII/UTOPIA Intel Quick Start Guide—Intel Jumper Description Ref ID for Installed State Connects ETH B-specific shared NPE...
-
Page 14: Intel ® Ixdp465 Baseboard Jumper Locations
® Intel IXDP465 Development Platform—Quick Start Guide ® Figure 3. Intel IXDP465 Baseboard Jumper Locations Installed = NOT Installed = May 2005 Intel JP128 ETH C JP127 UTOPIA JP11 ETH A S II ETH B II / S II / UTOPIA ®... -
Page 15: Intel ® Ixp465 Network Processor/Ddr Module Jumpers
ENSSCLK IXP COREV 667 MHz IXP 2.5V Intel Quick Start Guide—Intel Table 5 describes the jumper settings for the Intel Jumper Description Ref ID for Installed State Selects I2C pin, instead of GPIO Selects I2C pin, instead of GPIO JP45 Enables monitoring of +3.3V current... -
Page 16: Intel ® Ixp465 Network Processor/Ddr Module Jumper Locations
® Intel IXDP465 Development Platform—Quick Start Guide ® Figure 4. Intel IXP465 Network Processor/DDR Module Jumper Locations May 2005 Intel JP46 IXP 2.5V ® IXDP465 Development Platform Order Number: 305825, Revision: 002 SCL - P4 SDA - P2 IXP 3.3V... -
Page 17: Intel ® Ixpetm465 Ethernet Phy Mezzanine Card Jumpers
PHY Address A2 for MII-0 NPE-B Ethernet mezzanine slot PHY Address A3 for MII-0 NPE-B Ethernet mezzanine slot PHY Address A4 for MII-0 NPE-B Ethernet mezzanine slot ® IXDP465 Development Platform Order Number: 305825, Revision: 002 ® IXDP465 Development Platform Quick Start Default Settings Check? Not installed. -
Page 18: Lcd Display And Led Indicators
LEDs, so that they can be visually monitored for proper power-up and booting. The IXDP465 development platform provides a 2 x16-digit LCD display that can be used for software debug. The IXP465 Expansion Data Bus directly drives this display. When booting the... -
Page 19: Intel ® Ixpetm465 Ethernet Phy Mezzanine Card Jumper Descriptions And Default Settings . 17 7 Intel ® Ixdp465 Development Platform Led Descriptions And Default Settings
† Board silkscreen text reads “+1.5V” however, core voltage is actually 1.3/1.4V. Intel Quick Start Guide—Intel shows the exact locations for all LEDs on the IXDP465 development platform, Table LED Indication when ON +12V power is on +5V power is on -12V power is on +3.3V power is on... -
Page 20: Intel ® Ixdp465 Development Platform Led Locations
® Intel IXDP465 Development Platform—Quick Start Guide ® Figure 6. Intel IXDP465 Development Platform LED Locations C U ower LEDs FLASH STATUS Note: In the Power LED area, the silkscreen text reads “+1.5V” however, core voltage is actually 1.3/1.4V. May 2005... -
Page 21: Preparing The Platform For Initial Use
Preparing the Platform for Initial Use After unpacking the board and before powering on the board, the IXDP465 development platform needs to be prepared for first time use. To prepare the platform, follow these steps: 1. Verify that all default switch settings in 2. -
Page 22: Operating The Platform
IXDP465 Development Platform User’s Guide for detailed instructions on using the IXDP465 development platform, including how to update the IXDP465 development platform’s flash memory. 12.0 Technical Support If any of the contents are missing or if you have any questions, contact your local Intel representative. May 2005 Intel Figure ®...