Remote Control - Pioneer VSA-E03 Operating Instructions Manual

Remote Control

These pages describe the buttons on the remote control
used to operate the amplifier.
AMP
1
2
3
VOL
4
CHANNEL
5
MULTI CONTROL
DVD/LD
6
VCR 1
VCR 2
DSP MODE
1
CH.SELECT TEST TONE
7
5
CH.LEVEL
9
8 FUNCTION
MODE CHECK
9
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
1 AMP button
Press to switch the amplifier on or to put in standby.
2 MUTING button
Press to mute the volume. "MUTING" appears in the
display. Press again to cancel.
3 [When set to SURROUND]
@, #,%, fi, (Select/Adjust) buttons
[When set to other than OPERATIONS]
*(Pause), &(Stop), !(Rewind), ⁄(Fast Forward),
ENTER/‹(Play) buttons
[Tuner Operations]
FQ + (to higher frequencies), FQ – (to lower
frequencies), !(MPX), ⁄(DISP MODE), # (FM/AM)
buttons
!(MPX): Use to switch the auto stereo/monaural
mode for receiving FM broadcasts. When the
received broadcast signal is weak, press this button
to set the monaural mode.
⁄(DISP MODE): Use to switch the RDS data while
listening to an FM station. Each press changes the
display in the order of RT, PS, PTY, and frequency.
4 VOL (–/+) buttons
Press to adjust the volume. When VOL (–/+) buttons
are pressed while muting, muting is canceled.
5 CHANNEL (–/+) button
Use to select preset stations when operating the
tuner. When the remote is used to control other
components, this button may be used to change
channels, tracks, or chapters.
0
TV
-
FQ
+
ENTER
–
FQ
VOL
CD
TV/SAT
TUNER
TV CONTROL
=
MD/TAPE
AMP
MIDNIGHT
2
3 4
ATT SIG.SELECT
6
7 8
EFFECT
0 +10
MEMU
CLASS TV/VCR
DIRECT FL DIMMER
~
COMMANDER
SET UP
!
Î
@
Names of Parts and Basic Operations
6 MULTI CONTROL buttons
Use these buttons to select the remote operation
mode.
For example, pressing TUNER sets the remote to
operate the tuner functions.
7 Number buttons
These buttons can perform a variety of different
functions depending on the remote operation mode.
• [AMPLIFIER operations (press AMP first)]
: Switches the Dolby Surround mode on or
off(refer to page 29).
DSP MODE : Press repeatedly to select a DSP sound
mode (refer to page 26, 30).
MIDNIGHT : Press to hear surround sound effectively
at low volumes (refer to page 31).
CH.SELECT : Use to select a speaker when adjusting
speaker levels.
TEST TONE : Press to switch the test tone on or off
when listening to a surround mode (refer to page 19).
ATT : Press to attenuate (lower) the level of the input
signals and prevent distortion (refer to "Display", 5,
Overload indicator on page 22).
SIG.SELECT : When the same component uses both
analog and digital connections, use to select input
signals as digital or analog.
CH.LEVEL (–/+) : Use to adjust individual speaker
levels after having pressed CH. SELECT to select a
speaker channel.
EFFECT (–/+) : Use to adjust the DSP mode effect level.
8 FUNCTION button
Press repeatedly to select a source.
9 MODE CHECK button
Press to confirm the current remote operation mode
and to switch operation modes without changing the
source (refer to page 41).
0 Power button
Press to turn on or put in standby all connected
components other than this unit.
- TV, TV FUNC button
Press TV to turn the TV's power on or put in standby.
Press TV FUNC to select the TV for remote control
operation.
= AMP button
Press to select the amplifier for remote control
operation.
~ FL DIMMER button
Press to adjust the brightness of the fluorescent
display. Four levels of brightness ranging from very
dim to very bright can be selected.
! COMMANDER SET UP button
Use to customize the remote control functions.
(Refer to "Setting Up the Remote Control" starting on
page 20).
@ DIRECT button
Use to playback original source audio. When DIRECT
is ON, Dolby Surround, DSP, LOUDNESS, and
MIDNIGHT mode are automatically turned OFF.
23
En