Jøtul C 350 Installation And Operating Instructions Manual
Winterport fireplace insert
Hide thumbs
Also See for C 350:
- Installation and operating instructions manual (24 pages) ,
- Installation and operating instructions manual (24 pages)
Related Manuals for Jøtul C 350
Summary of Contents for Jøtul C 350
- Page 1 Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Jøtul C 350 Winterport Fireplace Insert Installation and Operating Instructions for the United States & Canada Keep these instructions for future reference.
- Page 2 Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Accepted For Use City of New York Department of Buildings MEA 429-07-E Jøtul North America, Inc. NOTICE: YOU SHOULD CONSULT THE AUTHO- RITY HAVING JURISDICTION IN YOUR LOCALE (SUCH AS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE PREVENTIOIN BUREAU, ETC.) BEFORE...
-
Page 3: Table Of Contents
Specifications the firebox and also at the front of the blower compartment. You may also wish to attach your Jøtul C 350 Winterport Fireplace Insert....6 sales receipt to this manual for future reference. Installation Model: Jøtul C 350 Winterport Fireplace Insert Masonry Fireplace Requirements ...... -
Page 4: Standards And Safety Notices Standards / Codes
Tested to U.S. Standards: ANSI/UL 1482, Canadian Standards: CAN/ULC-S627-M93 Check Building Codes Standards & Approvals The Jøtul C 350 Fireplace Insert has been tested and When installing, operating and maintaining your listed to: U.S: ANSI/UL 1482 Jøtul C 350 Fireplace Insert, follow the guidelines... -
Page 5: Safety Notices
Unpacking the Fireplace FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR All firebox components of the Jøtul C 350 Fireplace In- LOSS OF LIFE. sert are contained within the carton on a single pallet. • CONTACT THE LOCAL BUILDING OR FIRE... -
Page 6: Specifications
Performance Fuel: 20” Logs Heat Output 40,000 BTU/hr. (4.1 kg/ The Jøtul C 350 Winterport Fireplace Insert meets U.S. hr.) EPA emission limits for wood heaters sold after July Heating Capacity : Up to 1,300 sq. ft. 1990, and is tested and listed to ANSI/UL 1482, and... -
Page 7: Installation
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Installation Factory-Built Fireplace Requirements Masonry Fireplace Requirements The Jøtul C 350 Winterport may be installed into a • The entire fireplace and chimney must be cleaned factory-built fireplace with the following conditions: and inspected before installation. The system must meet local building code requirements. -
Page 8: Hearth Protection
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Hearth Protection Requirements The floor area in front of fireplace insert must be Min. protected from live sparks and radiant heat. 16” from door • Materials: Hearth protection must be non opening combustible insulating board, or the equiva- lent mortared masonry material. -
Page 9: Clearance To Combustibles
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Mantel Clearances Clearance to Combustible Materials Clearance reduction to mantel construction may be • There may be no combustible materials located made in conformance to NFPA 211 or CAN/CSA B365. anywhere within 36” (914 mm) of the front of the fireplace insert. -
Page 10: Chimney Connection
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 U.S. Requirement: The insert is connected to a listed stainless steel flexible connector that extends into the first chim- ney flue tile liner. A sealed block-off plate must be chimney connection components - these materials installed at the damper area of the existing fireplace. -
Page 11: Chimney Connection
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Installing the Fireplace Insert Chimney Connection Leveling Bolts This insert must be connected to a code-approved The leveling bolts are used to compensate for ir- masonry chimney or listed factory-built fireplace regular hearth surfaces. More importantly, they also... -
Page 12: Firebox Installation
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Install the Riser Bar Surround 1. If appropriate to your installation (see pg. 8), posi- Bracket tion the riser bar centered within the fireplace as shown in fig. 10. The forward ends of the Riser Bar should be aligned within 1/2 inch of the fireplace face. -
Page 13: Surround Assembly
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Figure 12. M6 x 10 Surround Panel assembly viewed Set Screw from backside. Right Breastplate Left Breastplate Tools Required: • 10 mm socket or wrench Hang Tabs Hang Tabs Right Leg Left Leg All fasteners are M6 x 10 mm hex head bolts, pre-installed. -
Page 14: Operation
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Operation Air Control Settings A single lever regulates the Primary Air flow that Read the following section carefully before building controls the intensity of the fire and consequent heat a fire in your fireplace insert.. -
Page 15: Starting / Maintaining The Fire
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Starting and Maintaining a Fire Keep logs behind Burn only solid wood directly on the bottom plate of Andirons the stove. Do not elevate the fire in any way. 1. Set the Air Control Lever in the full open position. 2. -
Page 16: Formation Of Creosote
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 It is also important to remember that chimney size, temperature and height all affect draft which in THIS BLOWER MUST BE ELECTRI- turn affects the formation of creosote. An exterior CALLY GROUNDED IN ACCOR- chimney, whether masonry or prefabricated steel,... -
Page 17: Maintenance
The container of ashes should be placed on a Replace glass only with part # 156069 noncombustible floor or on the ground, well away specifically designed for the Jøtul C 350 from all combustible materials, pending final dis- Winterport Fireplace insert. Do not use posal. -
Page 18: General Maintenance
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 General Maintenance Regular maintenance will assure proper perfor- Gaskets mance and prolong the life of your fireplace insert.. Check door and glass gaskets for seal integrity. The following procedures do not take long and are The gaskets should be soft enough to be somewhat generally inexpensive. - Page 19 Jøtul C 350 Winterport 138376_Rev_H 8.2.10...
- Page 20 Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Jøtul C 350 Winterport Illustrated Parts Diagram Figure 20.
-
Page 21: Parts List
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Jøtul C 350 Winterport Parts List Description PartNumber Rear Shroud 220904 Air Slider, Matte Black Paint 156092 Screw, #8 x 5/8” Hex Slt 117917 Air Slider, Nickel Plated 156094 Nut, M6 Flange 117968 Air Slider, Jøtul Iron Paint... -
Page 22: Miscellaneous Replacement Parts
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Appendix A Door Knob Installation Baffle Plate Removal The baffle assembly is easily removable following The Door Knob components are included in a sepa- rate bag contained within the Miscellaneous Kit in- these steps: cluded with the firebox. -
Page 23: Warranty Statement
Jøtul C 350 Winterport 138376_Rev_H 8.2.10 Jøtul Wood Product Warranty 4) Damage due to service performed by an installer or service agency, unless otherwise agreed to in writing by JØTUL. This warranty policy applies to wood-burning products identified 5) Damage caused by unauthorized modification, use or repair. - Page 24 Jøtul C 350 Winterport 138376_Rev_H 8.2.10 This appliance must be installed in conformance with local and national building regulations. It is important that the these instructions be carefully read and understood before beginning the instal- lation. Jøtul pursues a policy of continual product development. Consequently, products may differ in specification, color or type of accessories from those illustrated or described in various publications.