Starting Warm Engine; Stopping Engine - Shindaiwa EB212 Owner's/Operator's Manual

IMPORTANT
12
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
Do not allow the rope to snap back in. Always hold the unit firmly.
5. Recoil Starter
Place the unit on a flat, clear area. Firmly grasp throttle grip with left
hand and rapidly pull recoil starter handle/rope (E) until engine fires (5
6. Choke
pulls maximum).
After engine fires (or 5 pulls), move choke lever to "Run" (
position and pull starter handle/rope until engine starts and runs.
6. Choke
Allow unit to warm up at idle for several minutes.
After engine fires (or 5 pulls), move choke lever to "Run" (
NOTE
tion and pull starter handle/rope until engine starts and runs. Allow unit
If engine does not start with choke in "Run" position after 5 pulls,
to warm up at idle for several minutes.
repeat instructions 2- 5.
s
tartInG Warm enGIne
NOTE
7. After engine warm up, gradually depress throttle trigger to increase
If engine does not start with choke in "Run" position after 5 pulls,
s
engine RPM to operating speed.
tartInG Warm enGIne
The starting procedure is the same as Cold Start except DO NOT close
repeat instructions 2- 5.
the choke.
The starting procedure is the same as Cold Start except DO NOT close
7.

startIng warm engIne

After engine warm up, gradually depress throttle trigger to increase
the choke.
1. Stop Switch
engine RPM to operating speed.
The starting procedure is the same as Cold Start except DO NOT close
Move stop switch button (A) away from the STOP position.
the choke.
1.
Stop Switch
Move stop switch button (A) away from the STOP position.
2. Throttle Position
1. Stop Switch
Move throttle position lever (B) midway between idle and full throttle
Move stop switch button (A) away from the STOP position.
2. Throttle Position
positions.
Move throttle position lever (B) midway between idle and full throttle
2. Throttle Position
positions.
3. Recoil Starter
Move throttle position lever (B) midway between idle and full
Place the unit on a flat clear area. Firmly grasp throttle grip with left
throttle positions.
3. hand and rapidly pull recoil starter handle/rope (E) until engine fires. Recoil Starter
Place the unit on a flat clear area. Firmly grasp throttle grip with left
3. Recoil Starter hand and rapidly pull recoil starter handle/rope (E) until engine fires.
IMPORTANT
Place the unit on a flat clear area. Firmly grasp throttle grip with
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
left hand and rapidly pull recoil starter handle/rope (E) until en-
IMPORTANT
Do not allow the rope to snap back in. Always hold the unit firmly.
gine fires.
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
Do not allow the rope to snap back in. Always hold the unit firmly.
IMPORTANT
NOTE
Recoil starter: Use short pulls - only 1/2-2/3 of rope for start-
If engine does not start after 5 pulls, use Cold Start Procedure.
ing. Do not allow the rope to snap back in. Always hold the unit
NOTE
firmly.
If engine does not start after 5 pulls, use Cold Start Procedure.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
s
toppInG enGIne
s

stoppIng engIne

toppInG enGIne
1. Throttle Trigger/Throttle Position Lever
Release throttle trigger (F). Move throttle position lever (B) forward to
1. Throttle Trigger/Throttle Position Lever
1. Throttle Trigger/Throttle Position Lever
idle position and allow engine to return to idle before shutting engine off.
Release throttle trigger (F). Move throttle position lever (B)
Release throttle trigger (F). Move throttle position lever (B) forward to
forward to idle position and allow engine to return to idle before
idle position and allow engine to return to idle before shutting engine off.
shutting engine off.
2. Stop Switch
2. Stop Switch
Move stop switch (B) to "Stop" position.
Move stop switch (B) to "Stop" position.
2. Stop Switch
Move stop switch (B) to "Stop" position.
WARNING
WARNING
If engine does not stop when stop switch is moved to STOP position,
WARNING
If engine does not stop when stop switch is moved to STOP posi-
close choke - COLD START position - to stall engine. Have your
tion, close choke - COLD START position - to stall engine. Have
If engine does not stop when stop switch is moved to STOP position,
Shindaiwa dealer repair stop switch before using blower again.
your ECHO dealer repair stop switch before using blower again.
close choke - COLD START position - to stall engine. Have your
Shindaiwa dealer repair stop switch before using blower again.
)
) posi-
E
B
B
E
E
B
F
B
F
A
A
A
A
11