Air Filter; Fuel Filter - Shindaiwa EB212 Owner's/Operator's Manual

Level 1.
Tools required: 25-50 mm (1-2 in.) Cleaning brush.
NOTE
Clean daily.
a
Ir fIlter

aIr fIlter

1. Close choke (Cold Start Position [
ing the carburetor throat when the air filter is removed. Brush accumu-
Level 1.
Level 1. lated dirt from air cleaner area.
Tools required: 25-50 mm (1-2 in.) Cleaning brush.
Parts required: Air Filter
Remove air filter cover. Brush dirt from inside cover.
2.
NOTE
NOTE
Remove air filter and lightly brush debris from filter. Replace filter if
3.
Clean daily.
Clean daily.
it is damaged, fuel soaked, very dirty, or the rubber sealing edges are
deformed.
1. Close choke (Cold Start Position [
1. Close choke (Cold Start Position [
ing the carburetor throat when the air filter is removed. Brush accumu-
If filter can be reused, be certain it:
4.
entering the carburetor throat when the air filter is removed. Brush
lated dirt from air cleaner area.
accumulated dirt from air cleaner area.
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
Remove air filter cover. Brush dirt from inside cover.
2.
2. Remove air filter cover. Brush dirt from inside cover.
Install air filter cover.
5.
Remove air filter and lightly brush debris from filter. Replace filter if
3.
3. Remove air filter and lightly brush debris from filter. Replace
it is damaged, fuel soaked, very dirty, or the rubber sealing edges are
filter if it is damaged, fuel soaked, very dirty, or the rubber sealing
deformed.
edges are deformed.
f
uel fIlter
If filter can be reused, be certain it:
4.
4. If filter can be reused, be certain it:
Level 1.
• Fits tightly in the air filter cavity. • Fits tightly in the air filter cavity.
• Is installed with the original side out.
• Is installed with the original side out.
Tools required: 200-250 mm (8-10 in.) length of wire with one end
bent into a hook, Clean rag, funnel, and an approved fuel container.
5. Install air filter cover.
Install air filter cover.
5.

fuel fIlter

f
WARNING
uel fIlter
Level 1.
Fuel is VERY flammable. Use extreme care when mixing, storing
Level 1.
or handling.
Parts required: Fuel Filter
200-250 mm (8-10 in.) length of wire with one end
Tools required:
bent into a hook, Clean rag, funnel, and an approved fuel container.
1. Use a clean rag to remove loose dirt from around fuel cap and empty
WARNING
fuel tank.
Fuel is VERY flammable. Use extreme care when mixing, storing
Use the "fuel line hook" to pull the fuel line and filter from the tank.
2.
or handling.
WARNING
Fuel is VERY flammable. Use extreme care when mixing, storing
Remove the filter from the line and install the new filter.
3.
1. or handling. Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2. Use the "fuel line hook" to pull the fuel line and filter from the
1. Use a clean rag to remove loose dirt from around fuel cap and empty
tank.
fuel tank.
3. Remove the filter from the line and install the new filter.
Use the "fuel line hook" to pull the fuel line and filter from the tank.
2.
NOTE
Remove the filter from the line and install the new filter.
3.
Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the
United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.
When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to
replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replace-
ment part.)
]). This prevents dirt from enter-
]). This prevents dirt from enter-
]). This prevents dirt from
P B
ower lower
o ' M
Perator s
15
anual
15