Starting Your Spa; Start-Up Procedure; Electrical Diagrams; Therapy Pump Start-Up - Marquis Spas Owner's Manual

220-240V AC, 50 Hz:
Connections shall be made in accordance with the wiring diagram found on the
inside of the control box cover. Connections should be made with copper
conductors only – aluminum wiring should not be used with this system. All
conductors, circuit breakers, and/or fuses must be sized in accordance to the
input ratings shown below:
220-240 V AC, 50 Hz:
• Permanently connected
• Rated 220-240V AC – 50 Hz
• One and two pump spas are rated 16A for low amp setting (heater off
during high-speed) and 32A for high amp setting (heater on during high-
speed).
Improperly wired spas can cause irreversible damage resulting in blown fuse
and melted terminal block, and to other electrical components. Also, damage
caused to components or equipment caused by high or low voltage, brown outs
or electric surges is not covered under warranty.
Electrical Service Connections at Terminal Block, Inside Spa Controller:
The spa must be supplied through a single MCB with a certified residual current
device (RCD) with a rated current trip not exceeding 30 mA. Means for spa
disconnection from supply must be incorporated in the fixed wiring.
Recommended supply conductor nominal cross sectional area is 4mm2 for 16A
rating, 6 mm2 for 32A rating.
NOTE: If the power cord on any piece of electrical equipment, such as a jet
pump or ozone generator, becomes damaged, do not use the spa until the cord
has been repaired. Consult your authorized Marquis Spas® dealer for
assistance on such repair.
Electrical Diagram: Destiny, Envy, Euphoria, Mirage, Promise, Quest,
Rendezvous, Resort, Retreat, Reward and Spirit
Improperly wired spas are beyond Marquis Corp. control and are not covered
under the warranty. Other items beyond Marquis Corp. control include, but are
not limited to, damage resulting from: improper connections; accidents; failure to
follow procedures and instructions defined in the Marquis Spas® printed
instructions; cleaning agents; and natural occurrences including but not limited
to rodent or insect infestation, mold, lightning and other acts of nature.
®
M A R Q U I S S P A S
Electrical Diagram: Epic and Show

STARTING YOUR SPA

START-UP PROCEDURE

Your spa is equipped with solid-state Comfort Controls specific to your spa
model. (See SPA CONTROL OPERATION for your specific spa model.)
To start your spa, you need a spa water test kit or test strip and an underwater
thermometer. It is important to follow each of these steps when starting your spa.
Once you have completed the following steps, refer to the instructions in your start-
up kit for proper start-up water maintenance, or see MARQUIS SPA CARE.
NOTE: Your spa has been filled and test-run at the factory. The first time your
spa is filled with water, some discoloration from residual test water may appear.
This will disappear when the spa is completely filled and the filtration system is
functioning.
WARNING: Spa must be completely filled with water before turning on power.
Test the water for the proper chemical balance and adjust as necessary.
Marquis SpaCare™ products are recommended. (See WATER TREATMENT.)
PROPER CHEMICAL BALANCE IS IMPORTANT for your safety and the
longevity of your spa.
In the case of relocating your spa, it is imperative to follow the instructions in the
owner's manual. These instructions must remain with the spa. Damage caused
by relocating spa is not covered under warranty.
THERAPY PUMP(S)
Start-up procedure for all models
1. Place spa on a hard, flat, level surface. Make sure the power supply is
off.
2. Make sure the suction guard(s) in the footwell are in place and
undamaged.
3. Open the equipment door. Tighten all disconnects and open all shut-off
valves.
NOTE: Keep the drain valve closed at all times except when draining the spa
(do not rely on the cap to stop the flow of water). Not doing so could
result in damage to the drain valve due to freezing water.
4. Install filter cartridges. (See INSTALLATION INSTRUCTIONS, Filter
Cartridges.)
5. Fill the spa with water to two-thirds of the way up the Vortex skimmer
openings.
O W N E R ' S M A N U A L
4