Installation Instructions Location; Filter Cartridges; Electrical Requirements - Marquis Spas Owner's Manual

INSTALLATION INSTRUCTIONS
LOCATION
For your portable spa to function properly and safely, it must be located on a
hard, flat, level surface. Inground spas require special installation techniques
and should be planned in conjunction with your authorized Marquis Spas
dealer. Improper installation can result in structural damage to the spa and the
voiding of your spa warranty. Items to discuss with your dealer include: local
construction codes, electrical service requirements, serviceability of equipment,
existing underground obstructions such as gas, water, and telephone lines,
safety measures such as fences and locks, and visibility of the spa installation
from the home, street, and neighbours.
• Do not shim your spa. If your pad is not level you must pour a top cap:
contact a professional.
• Allow for sufficient water drainage around the spa to help preserve the
equipment and support structure. This includes indoor installations.
• A filled spa can weigh up to 2268 Kg and the location must support the
weight of the filled spa.
• Locate the equipment compartment where it will be accessible. Your spa
MUST be installed to permit access for servicing the equipment above and/or
below any decks or floors. Access is essential and must allow adequate room
for service. To facilitate repairs, Marquis Corp. or its agent may require
access to spa equipment. It is your responsibility to provide unencumbered
access. See spa diagrams for location of power supply.
• Leave access to the circuit breakers in the sub panel.
• Be sure the spa is level and in the final position BEFORE filling with water.
Check for power cords, tools, and hoses that may be caught underneath the
spa.
• Do not apply power to the spa before it is completely filled with water.
Damage to the pumps, heater and sensors may result.
• IMPORTANT: DO NOT LET AN EMPTY SPA REMAIN EXPOSED TO
DIRECT SUNLIGHT. Spa surface temperatures can reach in excess of 82°C
if left exposed to the sun. Significant damage can occur if this is allowed to
happen, including warping and blistering of the surface and components.
Damage that occurs as a result of this exposure is not covered under the
warranty.
• CAUTION: Never try to move a spa that has not been fully drained. To do so
could result in damage to the spa and physical injury to the mover.
• Cracks in the spa surface, exterior siding or DuraBase due to improper
transport or support of the spa are not covered under the warranty.
OUTDOOR AND PATIO INSTALLATION
To install the spa outdoors, we recommend a reinforced concrete pad at least 10
cm thick. The reinforcing material should be grounded per electrical codes.
If you place the spa on the ground, even temporarily, place the spa empty of
water on concrete pavers under the entire bottom of the spa. The concrete
pavers should be at least 5 cm thick and level across the entire surface. The spa
will inevitably settle and become out of level on this surface, thus it is important
to get the spa onto a solid foundation as soon as possible.
DECK INSTALLATION
Be sure the deck can support the weight of your filled spa by checking the
deck's maximum load capacity. Consult a qualified building contractor or
structural engineer. Minimum requirement is 45.36 Kgs. per 9.3 cm.
INDOOR INSTALLATION
There are special requirements if you place your spa indoors. Flooring material
must provide adequate traction when wet. Proper drainage is essential to
prevent water pooling. To avoid increased humidity, you need to provide proper
ventilation to the area. The addition of a ventilation system is recommended.
SHUT-OFF VALVES
Your spa is equipped with shut-off valves (see EQUIPMENT DIAGRAM) that
shut off the water flow to the equipment system for authorized Marquis Spas®
dealer service. At times, a new spa or one that has recently been serviced may
have the shut-off valves partially closed which can restrict the water flow and hinder
jet performance. Be sure the valves are fully open.
M A R Q U I S
FREEZE PROTECTION
When a freeze condition is detected (which occurs when the temperature in the
heater housing drops to 13°C), the jet pump(s) is automatically activated. In
areas with extremely cold winter conditions, your spa should be fine as long as it
is left running at normal operating temperatures. If you plan to turn the spa off,
follow the instructions in this manual (see SUSPENDED USE OR
®
WINTERIZING YOUR SPA).
OVERHEATING
In the case of extended hot weather, the spa water temperature may reach and
maintain 40°C to 41°C or higher. This is due to the ambient temperature and the
full insulation in the spa cabinet. You may have the option of shortening the
pump-run time. (See SPA CONTROL OPERATION for available options.)
FILTER CARTRIDGE(S)
Your portable spa features one or two Vortex filters.
Filter cartridges and filter lids are warranted to be free of defect at time of
delivery and do not qualify for labor coverage under the warranty. These parts
can be purchased or exchanged at your authorized Marquis Spas
NOTE: It is very important that the components of these filtration systems be
installed properly in the proper part of the spa.
1. Hold the Vortex filter cartridge and center it in the opening of the filter
housing.
2. Use the filter handle and turn the filter cartridge clockwise to screw it in
place. (Use caution not to over tighten as damage may occur to threads
and is not covered under warranty.)
3. Grasp the edge of the Vortex skimmer lid or Waterfall tray, center it over
the rings and gently snap in place. For Show spa, gently place the tray in
position resting the center point in the groove.
SUCTION GUARDS
The suction fitting(s) in the footwell of your spa is an opening through which the
jet pump(s) draws water. Suction fittings are equipped with a safety guard.
Suction through the fittings can be strong. The safety guard(s) must remain in
place and undamaged. A fitting with a damaged guard(s) can be dangerous,
especially to small children or people with long hair. Should any part of the body
become drawn to a fitting, immediately turn the jet pump(s) off. Long hair should
be restrained. Never allow long hair to float freely in the spa. Replace any
missing or damaged suction guard(s).
NOTE: It is normal for the flow rates of the suction fittings to vary from strong to
barely noticeable.

ELECTRICAL REQUIREMENTS

It is the responsibility of the spa owner to ensure that all electrical connections
are made in accordance with all electrical codes in effect at the time of
installation including proper bushings (at least 1 mm in diameter) at the spa
control and at the appliance openings. The recommended spa operating
environment is -5°C to +45°C, at 20-80 percent of relative humidity. Fuses are
covered to be free of defect at time of installation only.
Electrical Supply:
Insert the incoming electrical service line through
one of the access holes on either side of the spa
base (remove plastic plug). Then insert the service
through the electrical access hole of the control
box (see diagrams).
A pressure wire connector is located on the exterior of the control box. If the
installation includes a common bonding grid (reinforced concrete slab,
ground/earth plate beneath the spa, or any metal water pipe connection), this
pressure wire connector should be bonded to any metal ladder, water pipe, or
other metal, within 1.5 m of the spa and in accordance with pertinent electrical
codes.
®
S P A S O W N E R ' S M A N U A L
dealer.
®
3