CDA hc3620 Manual For Installation, Use And Maintenance

CDA hc3620 Manual For Installation, Use And Maintenance

Advertisement

Quick Links

hc3620 Built-In Ceramic Hob
Manual for Installation, Use and Maintenance

Advertisement

Table of Contents
loading

Summary of Contents for CDA hc3620

  • Page 1 Built-In Ceramic Hob Manual for Installation, Use and Maintenance...
  • Page 2: Table Of Contents

    Contents Contents ......................2 Important ......................3 Important Note ....................5 Using Your Hob ....................5 Using the Timer ..................... 10 Efficient Use of Your Hob ................13 Care and Maintenance ................15 Troubleshooting .................... 16 Electricity Supply to the Hob ..............17 Fitting the Hob ....................
  • Page 3: Important

    Appliance Information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model...
  • Page 4 At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative consequences for the environment and health. It also enables the constituent materials to be recovered, saving both energy and resources.
  • Page 5: Important Note

    • The appliance is not intended to be operated by any means of an external timer or separate remote-control system. Important Note Do not use the hob if the glass surface is cracked or damaged to prevent risk of electric shock. Disconnect it from the power supply.
  • Page 6 Control Panel: Timer Control Heating zone selection controls Key lock control Power / Timer adjusting controls ON/OFF control Using the Touch Controls The controls respond to touch, so you don’t need to apply any pressure. Use the ball of your finger, not its tip. You will hear a beep each time a touch is registered.
  • Page 7 To Switch Heating Zones On When the mains power supply is switched on, the buzzer beeps once and all the indicators light up for 1 second, then go out. This indicates that the ceramic hob has entered standby mode. Touch the ON/OFF control, all the indicators show “-“.
  • Page 8 zone you wish to switch off (for example back Turn the cooking zone off by using the controls to scroll down to “ 0 “. Alternatively, the zone may be switched off by touching the controls together. To switch all heating zones off at once it is only necessary to touch the ON/OFF control.
  • Page 9 To Unlock the Controls: Touch and hold the key lock control for approx. 2 seconds. The controls are now unlocked and the ceramic hob is ready for use. Warning: If the hob is switched off using the “ON/OFF” control while the controls are locked, it will be necessary to unlock the hob using the process above BEFORE the hob is next switched Over-Temperature Protection The ceramic hob is fitted with a sensor to monitor the temperature...
  • Page 10: Using The Timer

    Using the Timer You can use the timer in two different ways: • You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is up. • You can set it to turn one or more cooking zone(s) off after the set time.
  • Page 11 When the timer is set, it will begin to count down immediately. The display will show the remaining time. When the set time is reached the buzzer beeps for up to 30 seconds and the timer indicator shows “- - “. To cancel the beep touch either the control.
  • Page 12 When the timer is set, it will begin to count down immediately. The display will show the remaining time. To cancel the timer (at any point) touch the controls together, the timer is cancelled, and ”--“ will show in the minute display.
  • Page 13: Efficient Use Of Your Hob

    Efficient Use of Your Hob Before using your hob for the first time, switch the zones on for a FEW SECONDS to burn off any grease left over from the manufacturing process. The ceramic glass retains heat, so to make best use of the residual heat, switch off the zone five minutes prior to the end of cooking.
  • Page 14 suitable material and have the correct type of base. The base should be flat and smooth, as any rough part on the pan base could scratch the ceramic hob top. Choose pans which are between the sizes recommended in the table above, and with bases that are as non-reflective as possible, e.g.
  • Page 15: Care And Maintenance

    Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. You should use a non- abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings.
  • Page 16: Troubleshooting

    Troubleshooting Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services Problem Possible Causes Remedy The hob cannot No power. Ensure the hob is be turned on. connected to the power supply and that it is switched on.
  • Page 17: Electricity Supply To The Hob

    Electricity Supply to the Hob Mains electrical voltage: 220 -- - 240Vac, 50 Hz Total rated electrical consumption: 3.0 kW Warning: This appliance must be earthed. This appliance must be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet, protected by a 13A fuse.
  • Page 18 Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 1.5mm , HO5RR-F). • This appliance is intended to be connected to the mains supply with a cable of cross section area 1.5mm .
  • Page 19: Fitting The Hob

    Fitting the Hob Unpacking the Hob: Take care not to lose or mishandle any parts. Fitting Position of the Hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any adjacent vertical surfaces, e.g.
  • Page 20 • This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C or greater above ambient temperature. • If there is no oven to be built in below the hob, an isolation shelf should be fitted to protect the user from high temperatures.
  • Page 21: How To Install The Hob

    How to Install the Hob Overall dimensions of the hob: Width: 288mm Depth: 520mm Worktop cut-out dimensions: Width: 268mm Depth: 500mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance.
  • Page 22 NOTES:-...
  • Page 23 NOTES:-...
  • Page 24 4. brackets.

Table of Contents