Summary of Contents for Impex MARCY DIAMOND MD-8861
Page 1
NOTE: Please read all instructions carefully before using this product MARCY DIAMOND Table of Contents OLYMPIC BENCH Safety Notice Hardware Identifier MD-8861 Assembly Instruction Parts List Warranty Ordering Parts Model MD-8861 Retain This Manual for Reference 07-03-08 ® IMPEX INC.
ORDERING PARTS..................………… 13 BEFORE YOU BEGIN Thank you for selecting the MARCY DIAMOND MD-8861 Olympic Bench by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
Page 4
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Left Upright Beam. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Right and Left Upright Beams (#1 & #2) with a Cross Brace (#3) in the mid-span. Secure each end with two M10 x 4 ¾”...
Page 8
STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#6) onto the Main Seat Support (#4). Thread a M18 x 5/8” Lock Knob (#47) into the selected hole to hold the Sliding Block in position. B.) Attach the Main Seat Support to the Cross Brace (#3). C.) Secure it from the rear of the Cross Brace with two M10 x 2 ¾”...
Page 9
STEP 3 (See Diagram 3) A.) Attach the brackets at the end of the Backrest Supports (#32) to the pivot on the Sliding Block (#6). Align the holes on the Seat Support (#16) to the brackets on the Backrest Supports. Secure them together with one M12 x 7 5/8” Allen Bolt (#60), two 1” Washers (#66) and one M12 Aircraft Nut (#69).
Page 10
STEP 4 (See Diagram 4) A.) Insert two M10 x 2 3/8” Carriage Bolts (#56) all the way through the holes on the Leg Developer Holder (#5), then insert the two Bolts through the holes on the Main Seat Support (#4). Attach the Leg Developer Holder to the Main Seat Support. Secure them with the two M10 x 2 3/8”...
Page 11
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#28) to the Arm Curl Bracket (#34). Secure it with two M8 x 5/8” Allen Bolts (#61) and Ø 5/8” Washers (#65). Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#17).
PARTS LIST KEY NO. DESCRIPTION Q’ty Right Upright Beam Left Upright Beam 1” Square End Cap Cross Brace Ø ¾” Cone-shaped End Cap Main Seat Support 6” Arm Curl Handle Grip Leg Developer Holder M10 x 4 ¾” Carriage Bolt Sliding Block M10 x 3 ½”...
® IMPEX INC. LIMITED WARRANTY ®" IMPEX Inc. ("IMPEX ) warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.