Page 1 2009 Chevrolet TrailBlazer Owner Manual Seats and Restraint System ......1-1 Driving Your Vehicle ........4-1 Front Seats ..........1-2 Your Driving, the Road, and the Vehicle ..4-2 Rear Seats Towing ..........1-11 ........... 4-40 Service and Appearance Care ......5-1 Safety Belts ..........
Page 2: Canadian Owners
For vehicles ﬁrst sold in P.O. Box 07130 Canada, substitute the name “General Motors of Canada Detroit, MI 48207 Limited” for Chevrolet Motor Division wherever it appears 1-800-551-4123 in this manual. helminc.com This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3 Safety Warnings and Symbols CAUTION: A circle with a slash through it is a safety These mean there is something that could hurt symbol which means you or other people. “Do Not,” “Do not do this” or “Do not let this happen.” Cautions tell what the hazard is and what to do to avoid or reduce the hazard.
Page 4: Vehicle Symbols
Vehicle Symbols " : Charging System : Cruise Control The vehicle has components and labels that use symbols instead of text. Symbols are shown along : Engine Coolant Temperature with the text describing the operation or information relating to a speciﬁc component, control, message, : Exterior Lamps gage, or indicator.
Page 5: Table Of Contents
Section 1 Seats and Restraint System Front Seats ............1-2 Lower Anchors and Tethers for Manual Seats ..........1-2 Children (LATCH) ........1-43 Power Seats ..........1-3 Securing a Child Restraint in a Manual Lumbar ..........1-3 Rear Outside Seat Position ......1-49 Power Lumbar ..........1-4 Securing a Child Restraint in the Heated Seats ..........1-4 Center Rear Seat Position ......1-51...
Page 6 Front Seats If the vehicle has a manual seat, it can be moved forward or rearward. 1. Lift the bar to unlock Manual Seats the seat. 2. Slide the seat to the desired position and CAUTION: release the bar. You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
Page 7 Power Seats Manual Lumbar On vehicles with power On vehicles with this seats, the controls used to feature, the knob is operate them are located located on the outboard on the outboard side of side of the driver seat. the seats. To adjust the seat: •...
Page 8 Power Lumbar Heated Seats On vehicles with power Your vehicle may have lumbar, the control is heated front seats. The located on the outboard buttons used to control this side of the seat. feature are located on the front door armrests. The engine must be running for the heated seat feature to work.
Page 9 To heat only the seatback, press the vertical button with To store the memory settings: the heated seatback symbol. An indicator light on the 1. Adjust the driver’s seat, including the seatback button will come on to designate that only the seatback recliner and lumbar and the adjustable pedals, if is being heated.
Page 10: Easy Exit Seat
See “Seat Recall” under DIC Vehicle Customization on 3. Press and hold the easy exit seat button for more page 3-56 for more information. than three seconds. A double chime will sound to let you know that the position has been stored To stop recall movement of the memory seat feature at for the selected button 1 or 2.
Page 11 Reclining Seatbacks If the seats have manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat(s). Manual Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
Page 12: Power Reclining Seatbacks
Power Reclining Seatbacks To return the seatback to an upright position, do the following: If your seats have power 1. Lift the lever fully without applying pressure to the reclining seatbacks, use seatback and the seatback will return to the upright the vertical power seat position.
Page 13 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 14 Head Restraints Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the head restraint down. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head.
Page 15 Rear Seats Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts Rear Seat Operation and return them to their normal stowed position before folding a rear seat. Your vehicle has ﬂip and fold second row seats which provide additional cargo space.
Page 16 To return the seat(s) to the original position, do the following: CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
Page 17 Safety Belts CAUTION: Safety Belts: They Are for Everyone It is extremely dangerous to ride in a cargo area, This section of the manual describes how to use inside or outside of a vehicle. In a collision, people safety belts properly. It also describes some things not riding in these areas are more likely to be seriously to do with safety belts.
Page 18: Why Safety Belts Work
Why Safety Belts Work In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: When you ride in or on anything, you go as fast as You never know if you will be in a crash. If you do have it goes.
Page 19 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-15...
Page 20 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-16...
Page 21: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 22 How to Wear Safety Belts Properly If I am a good driver, and I never drive far from home, why should I wear safety belts? This section is only for people of adult size. You may be an excellent driver, but if you are in a Be aware that there are special things to know about crash —...
Page 23 In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.
Page 24 What is wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt snugly against your body. The shoulder belt is too loose.
Page 25 What is wrong with this? CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
Page 26 What is wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries.
Page 27 What is wrong with this? CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 28 What is wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 29 What is wrong with this? CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 30 What is wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 31 Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 32 4. To make the lap part tight, pull up on the To unlatch the belt, push the button on the buckle. shoulder belt. The belt should return to its stowed position. It may be necessary to pull stitching on the safety Before a door is closed, be sure the safety belt is out of belt through the latch plate to fully tighten the the way.
Page 33: Safety Belt Pretensioners
Safety Belt Pretensioners There is one guide for each outside passenger position in the rear seat. Here is how to install the comfort This vehicle has safety belt pretensioners for the guide to the shoulder belt: front outboard occupants. Although the safety belt 1.
Page 34 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 35 Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. 4. Buckle, position, and release the safety belt as described previously in this section.
Page 36 Safety Belt Extender Child Restraints If the safety belt will fasten around you, you should Older Children use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 37 The manufacturer’s instructions that come with the What is the proper way to wear safety belts? booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt An older child should wear a lap-shoulder belt and until the child passes the below ﬁt test: get the additional restraint a shoulder belt can provide.
Page 38 CAUTION: CAUTION: Never do this. Never do this. Never allow two children to wear the same safety Never allow a child to wear the safety belt with the belt. The safety belt can not properly spread the shoulder belt behind their back. A child can be impact forces.
Page 39 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants.
Page 40 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 41 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 42 What are the different types of add-on child restraints? CAUTION: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. To reduce the risk of neck and head injury during Selection of a particular restraint should take a crash, infants need complete support.
Page 43 Child Restraint Systems CAUTION: A rear-facing infant seat (A) provides restraint A young child’s hip bones are still so small that with the seating surface the vehicle’s regular safety belt may not remain against the back of low on the hip bones, as it should. Instead, it may the infant.
Page 44 A forward-facing child seat (B) provides restraint for the child’s body with the harness. A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window.
Page 45: Securing The Child Within The Child Restraint
Securing an Add-On Child Restraint in When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the Vehicle the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement CAUTION: copy from the manufacturer.
Page 46 Where to Put the Restraint CAUTION: (Continued) According to accident statistics, children and infants are safer when properly restrained in a child restraint forward-facing child restraint can be seriously system or infant restraint system secured in a rear injured or killed if the right front passenger airbag seating position.
Page 47: Lower Anchors And Tethers For Children (Latch)
When securing a child restraint in a rear seating position, Make sure that a LATCH-compatible child restraint is study the instructions that came with the child restraint to properly installed using the anchors, or use the vehicle’s make sure it is compatible with this vehicle. safety belts to secure the restraint, following the instructions that came with that restraint, and also the Wherever a child restraint is installed, be sure to secure...
Page 48: Top Tether Anchor
Lower Anchors Top Tether Anchor Lower anchors (A) are metal bars built into the vehicle. A top tether (A, C) anchors the top of the child restraint There are two lower anchors for each LATCH seating to the vehicle. A top tether anchor is built into the position that will accommodate a child restraint with vehicle.
Page 49 Some child restraints that have a top tether are designed To assist you in locating for use with or without the top tether being attached. the lower anchors, each Others require the top tether always to be attached. seating position with lower In Canada, the law requires that forward-facing anchors has two labels, child restraints have a top tether, and that the tether be...
Page 50: Securing A Child Restraint Designed For The Latch System
According to accident statistics children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 1-42 for additional information. Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to...
Page 51 Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage CAUTION: these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not attach more than one child restraint to a Do not fold the empty rear seat with a safety belt single anchor.
Page 52 2. If the child restraint manufacturer recommends that If the position you are the top tether be attached, attach and tighten the using does not have a top tether to the top tether anchor, if equipped. headrest or head restraint Refer to the child restraint instructions and and you are using a the following steps:...
Page 53: Securing A Child Restraint In A Rear Outside Seat Position
Securing a Child Restraint in a Rear If the position you are using has a headrest or Outside Seat Position head restraint and you are using a dual tether, When securing a child restraint in a rear seating route the tether around position, study the instructions that came with your child the headrest or head restraint to make sure it is compatible with this vehicle.
Page 54 If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 1-42. 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint.
Page 55: Securing A Child Restraint In The Center Rear Seat Position
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-43 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Page 56: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the CAUTION: (Continued) Right Front Seat Position forward-facing child restraint can be seriously This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to injured or killed if the right front passenger airbag Put the Restraint on page 1-42.
Page 57 If the child restraint has the LATCH system, see Lower 2. Put the child restraint on the seat. Anchors and Tethers for Children (LATCH) on page 1-43 3. Pick up the latch plate, and run the lap and shoulder for how and where to install the child restraint using portions of the vehicle’s safety belt through or LATCH.
Page 58 5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 59: Airbag System
If the airbag is off, the off indicator in the passenger All of the airbags in your vehicle will have the word airbag status indicator will come on and stay on when AIRBAG embossed in the trim or on an attached label the vehicle is started.
Page 60 Here are the most important things to know about the airbag system: CAUTION: CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously You can be severely injured or killed in a crash if injured or killed.
Page 61 There is an airbag readiness light on the CAUTION: instrument panel cluster, which shows the airbag symbol. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for The system checks the airbag electrical system for young children and infants.
Page 62: Where Are The Airbags
Where Are the Airbags? The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. The driver’s frontal airbag is in the middle of the steering wheel. 1-58...
Page 63 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag...
Page 64: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? • If the vehicle goes into an object at an angle, the airbags could inﬂate at a different crash speed Frontal airbags are designed to inﬂate in moderate to than if the vehicle goes straight into the object. severe frontal or near-frontal crashes to help reduce the Thresholds can also vary with speciﬁc vehicle design.
Page 65: What Makes An Airbag Inﬂate
How Does an Airbag Restrain? Roof-rail airbags are not intended to inﬂate in frontal impacts, near-frontal impacts, or rear impacts. Both roof-rail airbags will deploy when either side of the vehicle In moderate to severe frontal or near frontal collisions, is struck or if the sensing system predicts that the vehicle even belted occupants can contact the steering wheel is about to roll over.
Page 66: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag CAUTION: Inﬂates? After the frontal airbags inﬂate, they quickly deﬂate, so When an airbag inﬂates, there may be dust in the quickly that some people may not even realize an airbag air. This dust could cause breathing problems for inﬂated.
Page 67: Passenger Sensing System
Passenger Sensing System In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. The vehicle has a passenger sensing system for the right Additional windshield breakage may also occur front passenger position. The passenger airbag status from the right front passenger airbag.
Page 68 The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. CAUTION: The driver airbags and roof-rail airbags are not affected by the passenger sensing system. A child in a rear-facing child restraint can be The passenger sensing system works with sensors that seriously injured or killed if the right front are part of the right front passenger seat.
Page 69 The passenger sensing system is designed to turn off When the passenger sensing system has allowed the the right front passenger frontal airbag if: airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active. •...
Page 70 If the On Indicator is Lit for a Child If the Off Indicator is Lit for an Restraint Adult-Size Occupant If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3.
Page 71 If this happens, use the following steps to allow the A thick layer of additional material, such as a blanket or system to detect that person and enable the right front cushion, or aftermarket equipment such as seat covers, passenger frontal airbag: seat heaters, and seat massagers can affect how well the passenger sensing system operates.
Page 72: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Adding Equipment to Your Vehicle Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. Is there anything I might add to or change There are parts of the airbag system in several places about the vehicle that could keep the airbags around the vehicle.
Page 73 Any object, such as an aftermarket seat heater or a Because I have a disability, I have to get my comfort enhancing pad or device, installed under or vehicle modiﬁed. How can I ﬁnd out whether on top of the seat fabric, could also interfere with the this will affect my airbag system? operation of the passenger sensing system.
Page 74: Restraint System Check
Restraint System Check Airbags The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag Checking the Restraint Systems readiness light is working. See Airbag Readiness Light on page 3-32 for more information. Safety Belts Notice: If an airbag covering is damaged, opened, Now and then, check the safety belt reminder light, or broken, the airbag may not work properly.
Page 75: Replacing Restraint System Parts
Replacing Restraint System Parts If the vehicle has the LATCH system and it was being used during a crash, you may need new LATCH After a Crash system parts. New parts and repairs may be necessary even if the safety belt or LATCH system (if equipped), was CAUTION: not being used at the time of the crash.
Page 76 ✍ NOTES 1-72...
Page 77: Features And Controls
Section 2 Features and Controls Keys ...............2-3 Starting and Operating Your Vehicle ....2-21 Remote Keyless Entry (RKE) System ....2-4 New Vehicle Break-In ........2-21 Remote Keyless Entry (RKE) Ignition Positions ..........2-22 System Operation ........2-5 Retained Accessory Power (RAP) ....2-23 Starting the Engine ........2-23 Doors and Locks ..........2-7 Adjustable Throttle and Brake Pedal ....2-24 Door Locks ............2-7...
Page 78 Section 2 Features and Controls Outside Manual Mirrors ........2-43 Storage Areas ..........2-53 Outside Power Mirrors ........2-44 Glove Box ...........2-53 Outside Convex Mirror ........2-44 Overhead Console ........2-53 Outside Heated Mirrors ........2-44 Center Console Storage .........2-54 Luggage Carrier ...........2-54 ® OnStar System ..........2-45 Rear Floor Storage Cover ......2-55 Universal Home Remote System ......2-48 Convenience Net ..........2-56...
Page 79: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 80: Remote Keyless Entry (Rke) System
The key code number tells your dealer/retailer or a This device complies with RSS-210 of Industry Canada. qualiﬁed locksmith how to make extra keys. Keep this Operation is subject to the following two conditions: number in a safe place. If you lose your keys, you will be 1.
Page 81: System Operation
Remote Keyless Entry (RKE) (Lock): Press to lock all the doors. Press again within three seconds and the horn chirps. System Operation (Panic): Press to sound the horn. The headlamps The Remote Keyless Entry (RKE) transmitter functions and taillamps ﬂash for up to 30 seconds. To turn it work up to 30 feet (9 m) away from the vehicle.
Page 82: Battery Replacement
Battery Replacement To replace the battery: Replace the battery if the KEY FOB # BATTERY LOW message displays in the DIC. See “KEY FOB # BATTERY LOW” under DIC Warnings and Messages on page 3-51 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter.
Page 83: Doors And Locks
Doors and Locks There are several ways to lock and unlock your vehicle. You can use the remote keyless entry transmitter. You can use your key to unlock your door from the Door Locks outside. You can lock or unlock the door from the inside by CAUTION: sliding the manual lever...
Page 84: Power Door Locks
Power Door Locks Delayed Locking This feature delays the locking of the doors and the The power door lock liftgate when using the power lock or the remote keyless switches are located on entry system. the driver’s and front passenger’s door armrests. The ﬁrst press of the power door lock switch or lock button on the remote keyless entry transmitter with the driver’s door open will activate the delay locking.
Page 85: Programmable Automatic Door Locks
Programming Delayed Locking Programmable Locking Feature To turn the delayed locking feature on or off, do the Following are the two locking modes that can be following: programmed: 1. Press and hold the power door lock switch on the Mode 1: All doors lock when the transmission is shifted driver’s door in the lock position.
Page 86: Programmable Unlocking Feature
Programmable Unlocking Feature 3. You are now ready to program the automatic door locks. Select one of the two programming options The following is the list of available programming listed previously, and press the lock side of the options: power door lock switch to cycle through the lock options.
Page 87 To enter the program mode you need to do the following: programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the 1. Begin with the ignition off. Then pull the turn signal/ horn will chirp twice to indicate that you have left multifunction lever toward you and hold it there while the program mode.
Page 88: Rear Door Security Locks
Rear Door Security Locks The rear doors of your vehicle cannot be opened from the inside while this feature is in use. If you want to open the rear door while the security lock is on, unlock the Your vehicle may have this feature. You can lock the rear door and open the door from the outside.
Page 89: Liftgate/Liftglass
Liftgate/Liftglass Liftgate Release To unlock the liftgate, use the power door lock switch or the remote keyless entry transmitter. See Remote CAUTION: Keyless Entry (RKE) System Operation on page 2-5. The liftglass will also unlock when the liftgate is unlocked. It can be dangerous to drive with the liftgate or Press the button on the liftglass to open it.
Page 90: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 91: Power Windows
Power Windows CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Page 92: Sun Visors
Express-Down Window Sun Visors AUTO (Express-down): The driver’s and front Sun Visors with Slide Rod passenger’s window switches have an express-down Your vehicle may have this feature. Pull the sun visor feature that allows you to lower the window without down to block glare.
Page 93: Theft-Deterrent Systems
Theft-Deterrent Systems To operate the system: 1. Open the door. Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, 2. Lock the door with the power door lock switch or they do not make it impossible to steal. the Remote Keyless Entry (RKE) transmitter.
Page 94: Passlock (U.s. Only)
® Testing the Alarm Passlock (U.S. Only) To test the alarm: Your vehicle has the Passlock theft-deterrent system. Passlock is a passive theft-deterrent system that enables 1. From inside the vehicle, lower the driver’s window fuel if the ignition lock cylinder is turned with a valid key. If and open the driver’s door.
Page 95: Pass-Key Iii+ Electronic Immobilizer
® ® PASS-Key III+ Electronic PASS-Key III+ Electronic Immobilizer Immobilizer Operation (Canada Only) The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Your vehicle has a passive theft-deterrent system. Commission (FCC) Rules and with Industry Canada. The system is automatically armed when the key This device complies with Part 15 of the FCC Rules.
Page 96 If the engine still does not start, and the key appears to 4. Insert the second current driver’s key in the ignition be undamaged, try another ignition key. At this time, and start the engine within ten seconds of removing you may also want to check the fuse.
Page 97: Starting And Operating Your Vehicle
Starting and Operating Your • Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time the new brake Vehicle linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement.
Page 98: Ignition Positions
Ignition Positions The steering can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY. If The ignition switch has this doesn’t work, then the vehicle needs service. four different positions.
Page 99: Starting Procedure
Retained Accessory Power (RAP) Starting Procedure 1. With your foot off the accelerator pedal, turn the These vehicle accessories can be used for up to ignition to START. When the engine starts, let go of 20 minutes after the engine is turned off: the key.
Page 100: Adjustable Throttle And Brake Pedal
Adjustable Throttle and Brake Pedal 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), If the vehicle has this feature, you can change the it could be ﬂooded with too much gasoline. Try position of the throttle and brake pedals.
Page 101: Engine Coolant Heater
Engine Coolant Heater CAUTION: The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F (−18°C). Vehicles Plugging the cord into an ungrounded outlet could with an engine coolant heater should be plugged cause an electrical shock.
Page 102: Active Fuel Management
Active Fuel Management™ Automatic Transmission Operation The vehicle’s V8 engine may have Active Fuel There are several different Management™. This system allows the engine to positions for the gear shift operate on either all or half of its cylinders, depending lever.
Page 103 CAUTION: CAUTION: It is dangerous to get out of the vehicle if the shift If you have four-wheel drive, the vehicle will be free lever is not fully in P (Park) with the parking brake to roll — even if the shift lever is in P (Park) — if the ﬁrmly set.
Page 104 R (Reverse): Use this gear to back up. Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage Notice: Shifting to R (Reverse) while the vehicle is the transmission. The repairs would not be covered moving forward could damage the transmission.
Page 105 3 (Third): This position is also used for normal driving. 1 (First): This position reduces vehicle speed even It reduces vehicle speed more than D (Drive) without more than 2 (Second) without using the brakes. You using the brakes. You might choose 3 (Third) instead of can use it on very steep hills, or in deep snow or mud.
Page 106: Automatic Transfer Case
Four-Wheel Drive Automatic Transfer Case If the vehicle has four-wheel drive, the transfer case If the vehicle has four-wheel drive, the engine’s driving knob is located to the right of the steering wheel on the power can be sent to all four wheels for extra traction. instrument panel.
Page 107 AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road conditions are variable. CAUTION: When driving the vehicle in automatic four-wheel drive, the front axle is engaged, but the vehicle’s power is sent to the rear wheels. When the vehicle senses a Shifting the transfer case to Neutral can cause loss of traction, the system will automatically engage the vehicle to roll even if the transmission is in...
Page 108: Four-Wheel Drive
If the service Four-Wheel Drive Warning Light on the If you turn the knob to Four-Wheel Low when the instrument panel cluster stays on, you should take vehicle is in gear and/or moving, the Four-Wheel Low the vehicle to your dealer/retailer for service. See indicator light will ﬂash for 30 seconds and not complete Service Four-Wheel Drive Warning Light on page 3-45 the shift unless the vehicle is moving less than 2 mph...
Page 109: Shifting Into Neutral
Shifting into Neutral Shifting Out of Neutral Before shifting the transfer case to Neutral, ﬁrst make To shift the transfer case out of Neutral, do the following: sure the vehicle is parked so that it will not roll. 1. Set the parking brake and apply the regular brake pedal.
Page 110: Parking Brake
Parking Brake If the ignition is on, the brake system warning light on the instrument panel cluster will come on. See Brake System Warning Light on page 3-36. To set the parking brake, hold the regular brake Notice: Driving with the parking brake on can pedal down with your foot overheat the brake system and cause premature and pull up on the parking...
Page 111: Shifting Into Park
Shifting Into Park To shift into P (Park): 1. Hold the brake pedal down with your foot and set the parking brake. CAUTION: 2. Move the shift lever into P (Park) by pressing the button on the side of the shift lever and pushing the lever all the way toward the front of the vehicle.
Page 112: Torque Lock
Leaving the Vehicle With the Engine If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Park) and the parking Running brake is ﬁrmly set before you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down.
Page 113: Shifting Out Of Park
Shifting Out of Park If you still are unable to shift out of P (Park): 1. Fully release the shift lever button. The vehicle has an electronic shift lock release system. 2. Hold the brake pedal down and press the shift lever The shift lock release is designed to: button again.
Page 114: Engine Exhaust
Engine Exhaust CAUTION: (Continued) • CAUTION: The vehicle’s exhaust system has been modiﬁed, damaged or improperly repaired. • There are holes or openings in the vehicle Engine exhaust contains Carbon Monoxide (CO) body from damage or after-market which cannot be seen or smelled. Exposure to CO modiﬁcations that are not completely sealed.
Page 115: Running The Vehicle While Parked
Running the Vehicle While Parked CAUTION: (Continued) It is better not to park with the engine running. But if you ever have to, here are some things to know. Thevehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move CAUTION: suddenly.
Page 116: Mirrors
Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic-dimming rearview Manual Rearview Mirror mirror with a compass and/or temperature display. See Compass on page 2-42 for more information about Adjust the mirror to see clearly behind your vehicle. Hold the compass display.
Page 117: Temperature Display
Temperature Display Passenger Airbag Indicator The vehicle may be equipped with a passenger airbag Press or depending on the mirror, press TEMP to indicator, on the mirror glass, just above the buttons. turn the temperature display on or off. If the vehicle has this feature, the mirror displays To adjust between Fahrenheit and Celsius: the word ON, or an airbag symbol in Canada, when the passenger airbag is enabled.
Page 118: Compass
Compass In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, press Compass Operation and hold or depending on the mirror, press COMP until CAL displays. There is a compass display in the upper right corner of The compass can be calibrated by driving the vehicle in the mirror.
Page 119: Outside Manual Mirrors
To adjust for compass variance: 3. Keep pressing until the desired zone number displays. Release the button. After several seconds 1. Find your current location and variance zone of inactivity, the new zone number locks in and the number on the following zone map. compass display returns.
Page 120: Outside Power Mirrors
Outside Power Mirrors Outside Convex Mirror Vehicles with outside power mirrors have controls located on the driver door. CAUTION: To adjust the mirrors: 1. Turn the control knob left or right to select the A convex mirror can make things (like other driver’s or passenger mirror.
Page 121: Onstar System
® OnStar System OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the ﬁrst prepaid year, contact OnStar to select a monthly or annual subscription payment plan.
Page 122 OnStar Services Available with the OnStar Hands-Free Calling Safe & Sound Plan OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice • Automatic Notiﬁcation of Airbag Deployment commands. Hands-Free Calling is fully integrated into • Advanced Automatic Crash Notiﬁcation (AACN) the vehicle, and can be used with OnStar Pre-Paid (If equipped)
Page 123: Onstar Virtual Advisor
OnStar Virtual Advisor How OnStar Service Works OnStar Virtual Advisor is a feature of OnStar The OnStar system can record and transmit vehicle Hands-Free Calling that uses minutes to access information. This information is automatically sent to an location-based weather, local traffic reports, and OnStar Call Center when the OnStar button is pressed, stock quotes.
Page 124: Universal Home Remote System
Universal Home Remote Location information about the vehicle is only available if the GPS satellite signals are unobstructed and System available. The vehicle must have a working electrical system, The Universal Home Remote System provides a way to including adequate battery power, for the OnStar replace up to three hand-held Radio-Frequency (RF) equipment to operate.
Page 125: Universal Home Remote System
Universal Home Remote System Read the instructions completely before attempting to program the Universal Home Remote. Because of Operation (With One Triangular LED) the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote.
Page 126: Programming The Universal Home Remote System
Programming the Universal Home Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program Remote System the remaining two Universal Home Remote buttons. For questions or help programming the Universal Home Remote System, call 1-800-355-3515 or go to 2.
Page 127 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and the garage door should move when the Universal Home Remote button is pressed and released. There is no need to continue programming Steps 6 through 8.
Page 128: Gate Operator And Canadian Programming
Gate Operator and Canadian 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Programming Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not If you have questions or need help programming the move, press and hold the same button a second time Universal Home Remote System, call 1-800-355-3515 or...
Page 129: Storage Areas
Using Universal Home Remote Reprogramming a Single Universal Home Remote Button Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light To reprogram any of the three Universal Home Remote will come on while the signal is being transmitted. buttons, repeat the programming instructions earlier in this section, beginning with Step 2.
Page 130: Center Console Storage
Center Console Storage Luggage Carrier Pull the front lever on the center console while lifting the top to open it. CAUTION: The console has cupholders on the front and rear of the storage compartment. If something is carried on top of the vehicle that is The console may also contain: longer or wider than the luggage carrier —...
Page 131: Rear Floor Storage Cover
Rear Floor Storage Cover To slide the crossrails to where you want them, pull up on the lever on each side of the crossrail. This releases the crossrail and allows you to slide it. When the crossrail is where you want it, press down on CAUTION: the levers to lock it into place.
Page 132: Convenience Net
Convenience Net To remove the cargo cover, do the following: 1. Release the cover from the latch posts and carefully For vehicles with a convenience net located in the rear, roll it back up. use it to store small loads as far forward as possible. 2.
Page 133: Cargo Tie Downs
Cargo Tie Downs Press and release the back of the control in the overhead console to Four cargo tie-downs are located in the rear compartment open the sunroof. Press of the vehicle. The tie-downs can be used to secure small the front of the control loads.
Page 134 ✍ NOTES 2-58...
Page 135 Section 3 Instrument Panel Instrument Panel Overview .......3-4 Climate Controls ..........3-20 Hazard Warning Flashers ........3-6 Dual Climate Control System ......3-20 Horn .............3-6 Dual Automatic Climate Control System ...3-22 Tilt Wheel .............3-6 Outlet Adjustment .........3-26 Turn Signal/Multifunction Lever ......3-7 Rear Climate Control System ......3-27 Turn and Lane-Change Signals ......3-7 Warning Lights, Gages, and Indicators ....3-28 Headlamp High/Low-Beam Changer ....3-8...
Page 136 Section 3 Instrument Panel Security Light ..........3-44 Audio System(s) ..........3-62 Cruise Control Light ........3-44 Setting the Clock ..........3-63 Reduced Engine Power Light ......3-44 Radio(s) ............3-64 Highbeam On Light ........3-45 Using an MP3 ..........3-80 Service Four-Wheel Drive Warning Light ..3-45 XM Radio Messages ........3-84 Check Gages Warning Light ......3-45 Navigation/Radio System .......3-85 ®...
Page 137 ✍ NOTES...
Page 138: Instrument Panel Overview
Instrument Panel Overview...
Page 139 The main components of the instrument panel are the following: A. Headlamps on page 3-13. N. Hood Release on page 5-11. B. Air Outlets. See Outlet Adjustment on page 3-26. O. Driver Information Center (DIC) Steering Wheel Controls (If Equipped). See Driver Information C.
Page 140: Hazard Warning Flashers
Hazard Warning Flashers Tilt Wheel (Hazard Warning Flasher): Press this button The tilt lever is on the outboard side of the located on top of the steering column, to make the front steering column, under and rear turn signal lamps ﬂash on and off. This warns the turn signal lever.
Page 141: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change.
Page 142: Headlamp High/Low-Beam Changer
Turn Signal On Chime Flash-to-Pass A chime sounds if the turn signal has been on This feature lets high-beam headlamps be used to 3/4 of a mile (1.2 km). Move the turn signal lever to off. signal to a driver in front of you that you want to pass. It works even if the headlamps are in the automatic Headlamp High/Low-Beam Changer position.
Page 143: Windshield Wipers
Windshield Wipers Windshield Washer (Mist): Turn the band to mist, for a single wiping (Windshield Washer): Press the windshield cycle. Hold it there until the wipers start, then release it. washer paddle to spray washer ﬂuid on the windshield. The wipers will stop after one wipe. Hold the band on The wipers will clear the window and then either mist longer if more wipe cycles are needed.
Page 144: Rear Window Wiper/Washer
Rear Window Wiper/Washer To turn the rear wiper on, turn the control to either 1, 2, or 3. For delayed wiping, turn the control to 1 or 2. For steady wiping, turn the control to 3. To turn the wiper off, turn the control to 0. CAUTION: To wash the rear window, press located in the...
Page 145 (Off): Turns the cruise control system off and cancels the set speed memory. CAUTION: (On): Turns the cruise control system on. Cruise control can be dangerous where you (Resume/Accelerate): Resume a set speed or to cannot drive safely at a steady speed. So, do accelerate.
Page 146 Setting Cruise Control If the switch is held on resume/accelerate, the vehicle keeps going faster until the switch is released or the brakes are applied. So unless you want the vehicle 1. Move the cruise control switch to to go faster, do not hold the switch at resume/accelerate. 2.
Page 147: Headlamps
Passing Another Vehicle While Using Headlamps Cruise Control The exterior lamps knob is Use the accelerator pedal to increase the vehicle speed. located on the instrument When you take your foot off the pedal, the vehicle will panel. slow down to the cruise control speed set earlier. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load and the steepness of the hills.
Page 148: Headlamps On Reminder
Daytime Running Lamps (DRL) (Parking Lamps): Turns on the parking lamps, as well as the following: Daytime Running Lamps (DRL) can make it easier • Sidemarker Lamps for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles ﬁrst •...
Page 149: Automatic Headlamp System
Automatic Headlamp System driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system are only affected when the light sensor sees a When it is dark enough outside, the Automatic change in lighting lasting longer than the delay. Headlamp System turns on the headlamps when the vehicle is started and after the transmission has been If the vehicle is started in a dark garage, the automatic...
Page 150: Fog Lamps
Fog Lamps Instrument Panel Brightness For vehicles with fog lamps, the button is located on the Press the knob located instrument panel to the right of the exterior lamps knob. next to the exterior lamps Use the fog lamps for better vision in foggy or misty knob to extend it.
Page 151: Dome Lamps
Dome Lamps Entry Lighting The dome lamps come on when a door is opened, The vehicle has entry lighting. unless the dome lamp override button is pressed in. When any door is opened, the dome lamps come on as long as the dome override lamp override button Dome Lamp Override is not pressed in.
Page 152: Electric Power Management
Electric Power Management idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. Normally, these actions occur in steps or levels, without It then adjusts the voltage for best performance and being noticeable.
Page 153: Accessory Power Outlet(S)
Accessory Power Outlet(s) Notice: Improper use of the power outlet can cause damage not covered by the warranty. Do not hang any type of accessory or accessory bracket from the Accessory power outlets let you plug in auxiliary plug because the power outlets are designed for electrical equipment, such as a cellular telephone.
Page 154: Climate Controls
Climate Controls Passenger Side Temperature Lever: Raise or lower the lever to increase or decrease the temperature on the passenger side of the vehicle. This right lever Dual Climate Control System also adjusts the temperature to the rear seat outlets. When the temperature outside is 0°F (-18°C) or lower, With this system the heating, cooling, and ventilation use the engine coolant heater, if the vehicle has one,...
Page 155 (Floor): Air is directed to the ﬂoor outlets, with (Air Conditioning): Press to turn the some air directed to the windshield and the side window air-conditioning system on or off. An indicator light outlets. The recirculation button cannot be selected comes on and the system begins to cool and dehumidify while in ﬂoor mode.
Page 156: Dual Automatic Climate Control System
Rear Window Defogger Dual Automatic Climate Control System The rear window defogger uses a warming grid to remove fog from the rear window. With this system the heating, cooling and ventilation < can be controlled on the vehicle. When the vehicle is (Rear): Press to turn the rear window defogger ﬁrst started and the climate control system is on, or if the on or off.
Page 157: Manual Operation
Outside Air Temperature Display 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 72°F (22°C) A new outside temperature reading is displayed if temperature setting and allow about 20 minutes for the vehicle has been off for more than three hours. the system to adjust.
Page 158 Passenger Side Temperature Knob: Turn clockwise To change the current air delivery mode, select one of or counterclockwise to increase or decrease the the following: temperature on the passenger side of the vehicle. The (Vent): Air is directed to the instrument panel display will show the temperature setting decreasing or increasing and an arrow pointing toward the passenger.
Page 159 A/C (Air Conditioning): Press to turn the air (Recirculation): Press to turn the recirculation conditioning system on or off. When the system is on, mode on or off. An indicator light comes on to show the system automatically begins to cool and dehumidify that recirculation is on.
Page 160: Outlet Adjustment
Rear Window Defogger Outlet Adjustment The rear window defogger uses a warming grid to Use the air outlets located in the center and on the side remove fog from the rear window. of the instrument panel to direct the airﬂow. Use the thumbwheels near the air outlets to open or close off <...
Page 161: Rear Climate Control System
Rear Climate Control System Air Delivery Mode Control: Turn clockwise or counterclockwise to change the direction of the airﬂow to the rear seat area. The vehicle has one of the following rear climate control systems. With either of these systems, the rear climate (Panel): Air is directed to the rear console outlets.
Page 162: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and If the vehicle has the rear seat audio system, the lower buttons are used to adjust the rear seat climate control Indicators system. The temperature of the air coming through the rear outlets is determined by the front passenger Warning lights and gages can signal that something is temperature setting.
Page 163: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Page 164: Speedometer And Odometer
Speedometer and Odometer Tachometer The speedometer the vehicle speed in both miles per The tachometer hour (mph) and kilometers per hour (km/h). displays the engine The odometer shows how far the vehicle has been speed in revolutions driven, in either miles (used in the United States) per minute (rpm).
Page 165: Safety Belt Reminders
Safety Belt Reminders Passenger Safety Belt Reminder Light Several seconds after the engine is started, a Safety Belt Reminder Light chime sounds for several seconds to remind the front passenger to buckle their safety belt. This only occurs When the engine is started, a chime sounds for several if the passenger airbag is enabled.
Page 166: Airbag Readiness Light
Airbag Readiness Light CAUTION: The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes If the airbag readiness light stays on after the the airbag sensor, the pretensioners, the airbag modules, vehicle is started or comes on while driving, the wiring and the crash sensing and diagnostic module.
Page 167: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after The vehicle has the passenger sensing system. several more seconds, the status indicator will light either See Passenger Sensing System on page 1-63 for ON or OFF, or either the on or off symbol to let you know...
Page 168: Charging System Light
Charging System Light If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing This light comes on brieﬂy system. See your dealer/retailer for service. when the ignition key is turned to START, but the engine is not running, as a...
Page 169: Voltmeter Gage
Voltmeter Gage Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left idling for an extended When your engine is not period. This condition is normal since the charging running, but the ignition is system is not able to provide full power at engine idle.
Page 170: Brake System Warning Light
Brake System Warning Light This light should come on brieﬂy when you turn the ignition key to ON/RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there When the ignition is on, the brake system warning light is a problem.
Page 171: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on Warning Light page 3-36. For vehicles with a Driver Information Center (DIC), For vehicles with see DIC Warnings and Messages on page 3-51 for the Antilock Brake all brake related DIC messages.
Page 172: Stabilitrak Indicator Light
® StabiliTrak Indicator Light Engine Coolant Temperature Gage This warning light should come on brieﬂy when the engine is started. During most driving conditions, this light will not come ® on. If the StabiliTrak System is actively controlling the stability and/or traction of the vehicle, this light United States Canada will ﬂash.
Page 173: Tire Pressure Light
Tire Pressure Light When the Light Flashes First and Then is On Steady For vehicles with a tire This indicates that there could be a problem with the pressure light, this light Tire Pressure Monitor System. The light ﬂashes for about comes on brieﬂy when a minute and stays on steady for the remainder of the the engine is started and...
Page 174 If the check engine light comes on and stays on, while This light comes on during a malfunction in one of the engine is running, this indicates that there is an two ways: OBD II problem and service is required. Light Flashing: A misﬁre condition has been detected.
Page 175 • Light On Steady: An emission control system Make sure to fuel the vehicle with quality fuel. malfunction has been detected on the vehicle. Poor fuel quality causes the engine not to run as Diagnosis and service might be required. efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into An emission system malfunction might be corrected by...
Page 176: Oil Pressure Gage
Emissions Inspection and Maintenance Oil Pressure Gage Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: •...
Page 177: Maintenance Schedule
Change Engine Oil Light CAUTION: Your vehicle may have a change engine oil light. Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Page 178: Security Light
Security Light Reduced Engine Power Light For information regarding This light comes on when this light and the vehicle’s a noticeable reduction in security system, see the vehicle’s performance Content Theft-Deterrent occurs. on page 2-17. The vehicle can be driven at a reduced speed when Cruise Control Light the reduced engine power light is on, but acceleration and speed may be reduced.
Page 179: Highbeam On Light
Highbeam On Light The service four-wheel drive light comes on, except for the SS model, to indicate that there may be a problem with the drive system and service is required. This light comes on when Malfunctions can be indicated by the system before any the high-beam headlamps problem is apparent, which may prevent serious damage are in use.
Page 180: Gate Ajar Light
Gate Ajar Light When the ignition is on, the fuel gage tells you about how much fuel you have remaining. An arrow on the fuel gage indicates the side of the If this light comes on, the vehicle the fuel door is on. liftgate or liftglass is not completely shut.
Page 181: Low Fuel Warning Light
Low Fuel Warning Light Driver Information Center (DIC) The light next to the fuel gage will come on brieﬂy when Your vehicle may have this feature. The Driver you are starting the engine. Information Center (DIC) display is located on the instrument panel cluster, below the speedometer.
Page 182: Dic Operation And Displays
DIC Operation and Displays The DIC comes on when the ignition is on. After a short delay the DIC will display the information that was last displayed before the engine was turned off. If a problem is detected, a warning message will appear on the display.
Page 183: Trip Information Button
Trip Information Button Tire Pressures: On vehicles with the Tire Pressure Monitor System (TPMS), press the trip information button until TIRE PRESSURES appears on the display. (Trip Information): Press the trip information This mode shows the tire pressure in pounds per button to scroll through the ODOMETER, TRIP A, square inch (psi) or kilopascals (kPa).
Page 184: Maintenance Schedule
Fuel Information Button Average Fuel Economy: Press the fuel information button until AVG. ECON appears on the display. This mode shows how many miles per gallon (MPG), (Fuel Information): Press the fuel information liters per 100 kilometers (L/100 km), or kilometers button to scroll through the range, fuel used, average per liter (km/L) your vehicle is getting based on current fuel economy, and the engine oil life system.
Page 185: Select Button
Customization Button Some messages may not require immediate action. Press any of the DIC buttons on the steering wheel or the trip odometer reset stem on the instrument panel (Customization): Press the customization button to cluster to acknowledge that you received the messages access the VEHICLE SETTINGS menu and customize and to clear them from the display.
Page 186: Check Tire Pressure
CHECK TIRE PRESSURE DRIVER DOOR AJAR On vehicles with the Tire Pressure Monitor System This message displays and a chime sounds if the driver (TPMS), this message displays when the pressure in door is not fully closed. Stop and turn off the vehicle, one or more of the vehicle’s tires needs to be checked.
Page 187: Fuel Level Low
FUEL LEVEL LOW OIL PRESSURE LOW/STOP ENGINE This message displays and a chime sounds if the fuel Notice: If you drive your vehicle while the engine level is low. Refuel as soon as possible. See Low oil pressure is low, severe engine damage may occur. Fuel Warning Light on page 3-47, Filling the Tank on If a low oil pressure warning appears on the Driver page 5-8, and Fuel on page 5-5 for more information.
Page 188: Right Rear Door Ajar
RIGHT REAR DOOR AJAR SERVICE CHARGING SYS (System) This message displays and a chime sounds if the This message displays if there is a problem with the passenger side rear door is not fully closed. Stop and battery charging system. Under certain conditions, the turn off the vehicle, check the door for obstructions, charging system light may also turn on in the instrument and close the door again.
Page 189: Service Tire Monitor
SERVICE TIRE MONITOR STABILITRAK OFF On vehicles with the Tire Pressure Monitor This message displays when you press the StabiliTrak System (TPMS), this message displays if a part button for more than ﬁve seconds or when stability on the TPMS is not working properly. The tire pressure control has been automatically disabled.
Page 190: Dic Vehicle Customization
TIGHTEN FUEL CAP DIC Vehicle Customization This message may display and a chime may sound Your vehicle may have customization capabilities that if the vehicle’s fuel cap is not tightened properly. Fully allow you to program some features to one setting reinstall the fuel cap.
Page 191 Lock Doors Unlock Doors Press until LOCK DOORS: IN GEAR appears in the Press until UNLOCK DOORS: IN PARK appears display. To select your preference for automatic locking, in the display. To select your preference for automatic press while LOCK DOORS: IN GEAR is displayed unlocking, press while UNLOCK DOORS: IN PARK on the DIC.
Page 192: Unlock Feedback
Lock Feedback Unlock Feedback Press until LOCK FEEDBACK: BOTH appears in Press until UNLOCK FEEDBACK: LAMPS appears the display. To select your preference for the feedback in the display. To select your preference for the you receive when locking the vehicle with the Remote feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter, Keyless Entry (RKE) transmitter, press...
Page 193 Headlamp Delay Perimeter Lights Press until HEADLAMP DELAY: 10 SEC appears Press until PERIMETER LIGHTS: ON appears in the in the display. To select your preference for how long display. To select your preference for perimeter lighting, the headlamps will stay on after you turn off the vehicle, press while PERIMETER LIGHTS: ON is displayed press...
Page 194 Easy Exit Seat Seat Recall Press until EASY EXIT SEAT: OFF appears in the Press until SEAT RECALL: OFF appears in the display. To select your preference for seat position exit, display. To select your preference for recall of the driver’s memory seat and adjustable pedals, if your vehicle has press while EASY EXIT SEAT: OFF is displayed...
Page 195: Alarm Warning
Alarm Warning Language Press until ALARM WARNING: BOTH appears in Press until LANGUAGE: ENGLISH appears in the the display. To select your preference for alarm warning, display. To select your preference for display language, press while ALARM WARNING: BOTH is displayed press while LANGUAGE: ENGLISH is displayed on the DIC.
Page 196: Audio System(S)
Units Audio System(s) Press until UNITS: U.S. (ENGLISH) appears in the Determine which radio the vehicle has and read the display. To select the units of measurement in which the following pages to become familiar with its features. DIC will display vehicle information, press while UNITS: U.S.
Page 197: Setting The Clock
Setting the Clock Notice: Contact your dealer/retailer before adding any equipment. The clock can be set with the ignition on or off. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, The radio may have a button marked with an H or HR to radio, or other systems, and could damage them.
Page 198: Radio(S)
Radio(s) ® Base MP3 Radio shown, Bose similar ® Base Radio Shown, Bose Similar 3-64...
Page 199 Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming.
Page 200: Playing The Radio
Playing the Radio To change the default on the display, press the DISPL or INFO knob until the desired display is shown, then brieﬂy press and hold the knob until a beep is PWR (Power): Push to turn the system on and off. heard.
Page 201: Finding A Station
Finding a Station Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, BAND: Press to choose between FM1, FM2, AM, or six XM1 and six XM2, can be programed on the XM1 or XM2. six numbered pushbuttons, by performing the following steps: TUNE : Turn to select radio stations.
Page 202: Adjusting The Speakers (Balance/Fade
Setting the Tone Adjusting the Speakers (Balance/Fade) (Bass/Midrange/Treble) AUDIO: Press and turn to adjust the speakers. AUDIO: Press and turn to adjust the Tone. To adjust the balance between the right and the left 1. Push and release until BASS, MID (midrange) speakers: ®...
Page 203: Rds And Xm
Finding a Program Type (PTY) Station SCAN: To scan the stations within a PTY for all Radios except the MP3 Radio: (RDS and XM) 1. Press the TYPE button to activate program type To select and ﬁnd a desired PTY select mode.
Page 204 Setting Preset PTYs (RDS Only) If both PTY and TRAF are on, the radio searches for stations with the selected PTY and traffic For the Base Radio, pushbuttons have factory PTY announcements. presets. Up to 12 PTYs (six FM1 and six FM2), can If the radio cannot ﬁnd the desired program type, NONE be programmed on the six numbered pushbuttons, displays and the radio returns to the last station.
Page 205: Rds Messages
RDS Messages If TRAF displays, press the TRAF button to turn off the traffic announcements. ALERT! (MP3 Radio): Alert warns of local or national The radio plays the traffic announcement if the volume is emergencies. When an alert announcement comes low.
Page 206: Radio Messages
Radio Messages Radio Messages for XM Only See XM Radio Messages on page 3-84 later in this CAL ERR (Calibration Error): Displays if the radio is section for further detail. no longer calibrated properly for the vehicle. The vehicle must be returned to your dealer/retailer for service. Playing a CD ®...
Page 207 Care of CDs Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an Sound quality can be reduced due to CD-R quality, attempt is made to play scratched or damaged CDs, the method of recording, the quality of the music that has the CD player could be damaged.
Page 208 Playing a Speciﬁc Loaded CD To insert multiple CDs: 1. Turn the ignition on. For every CD loaded, a number displays. To play a 2. Press and hold the LOAD button for two seconds. speciﬁc CD, ﬁrst press the CD AUX button (if not already in CD mode), then press the numbered pushbutton A beep sounds and the indicator light, located that corresponds to the CD.
Page 209 If the CD is not removed, after 25 seconds, the CD REV or 3 REV (Reverse): Press and hold to automatically pulls back into the player. If CD is pushed reverse quickly within a track. back into the player, before the 25-second time period is For the Base Radio, press and hold for less than complete, the player senses an error and tries to eject the two seconds to reverse at six times the normal playing...
Page 210 To use repeat, do the following: AUTO EQ (Automatic Equalization): Press to select the equalization setting while playing a CD. • To repeat a track, press and release the The equalization is stored when a CD is played. RPT button. RPT displays. Press again to For more information on AUTO EQ, see “AUTO EQ”...
Page 211: Using Song List Mode
Using Song List Mode To scan all loaded CDs, press and hold either SCAN arrow for more than four seconds until ALL CD SCAN The six-disc CD changer has a feature called song list. displays and a beep sounds. Use this feature to listen to This feature is capable of saving 20 track selections.
Page 212 To play the song list, press the SONG LIST button. To delete the entire song list: One beep sounds and S-LIST displays. The recorded 1. Turn the CD player on. tracks begin to play in the order they were saved. 2.
Page 213 CD Messages Listening to a DVD If the vehicle has the Rear Seat Entertainment (RSE) CHECK CD: If this message displays and/or the CD system and a DVD is playing, the DVD symbol displays ejects, it could be for one of the following reasons: indicating that the DVD is available and can be listened to •...
Page 214: Using An Mp3
Using an MP3 may use more disc memory space than necessary. To conserve space on the disc, minimize the length of the ﬁle, folder, or playlist names. An MP3 CD that was MP3/WMA Disc recorded using no ﬁle folders can also be played. The system can support up to 11 folders in depth, though, MP3/WMA Format keep the depth of the folders to a minimum in order to...
Page 215 No Folder When play enters a new folder, the display does not automatically show the new folder name unless the When the CD contains only compressed ﬁles, the ﬁles folder mode has been chosen as the default display. are located under the root folder. The next and previous See DISPL (display) later in this section for more folder functions do not function on a CD that was information.
Page 216: Playing An Mp3/Wma
Playing an MP3/WMA 3 REV (Reverse): Press and hold to reverse quickly within a track. Press and hold 3 REV for less than Insert a CD partway into the slot, label side up. The two seconds to reverse at 10 times the normal playing player pulls it in, and READING displays.
Page 217 To change the default on the display, press the DISPL SEEK : Press the left SEEK arrow to go to the knob until the desired display appears, then press and start of the previous track. Press the right SEEK arrow to hold this knob for two seconds.
Page 218: Xm Radio Messages
XM Radio Messages CH Unauth: This channel is blocked or cannot be received with your XM Subscription package. xL (Explicit Language Channels): These channels, Unauth: This channel is blocked or cannot be received or any others, can be blocked by calling with your XM Subscription package.
Page 219: Voice Recognition
® Bluetooth XM Lock: The XM receiver in your vehicle could have previously been in another vehicle. For security purposes, XM receivers cannot be swapped between Vehicles with a Bluetooth system can use a Bluetooth vehicles. If this message is received after having your capable cell phone with a Hands Free Proﬁle to make and vehicle serviced, check with your dealer/retailer.
Page 220: Audio System
Audio System Pairing When using the in-vehicle Bluetooth system, sound A Bluetooth enabled cell phone must be paired to the comes through the vehicle’s front audio system speakers in-vehicle Bluetooth system ﬁrst and then connected to and overrides the audio system. Use the audio system the vehicle before it can be used.
Page 221: Pairing A Phone
Pairing a Phone Listing All Paired and Connected Phones 1. Press and hold for two seconds. The system 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. responds with “Ready” followed by a tone. 2.
Page 222: Storing Name Tags
Linking to a Different Phone Using the Store Command The store command allows a phone number to be 1. Press and hold for two seconds. The system stored without entering the digits individually. responds with “Ready” followed by a tone. 1.
Page 223 5. Say a name tag for the phone number. The name 4. After the complete number has been entered, say tag is recorded and the system responds with “Store”. The system responds with “Please say the “About to store <name tag>. Does that sound OK?”. name tag”...
Page 224: Making A Call
Deleting Name Tags Using the Delete All Name Tags Command The delete all name tags command deletes all stored The system uses the following commands to delete phone book name tags and route name tags for OnStar name tags: (if present). •...
Page 225: Using The Dial Command
Using the Dial Command Using the Digit Dial Command 1. Press and hold for two seconds. The system 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. responds with “Ready” followed by a tone. 2.
Page 226: Receiving A Call
Using the Call Command Using the Re-dial Command 1. Press and hold for two seconds. The system 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. responds with “Ready” followed by a tone. 2.
Page 227: Transferring A Call
Three-Way Calling To Mute a call 1. Press . The system responds with “Ready” Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier followed by a tone. to work. 2. Say “Mute Call”. The system responds with “Call muted”.
Page 228: Bluetooth System
To Transfer Audio to the In-Vehicle Dual Tone Multi-Frequency (DTMF) Bluetooth System Tones The cellular phone must be paired and connected with The in-vehicle Bluetooth system can send numbers and the Bluetooth system before a call can be transferred. numbers stored as name tags during a call. This is used The connection process can take up to two minutes after when calling a menu driven phone system.
Page 229: Other Information
Sending a Stored Name Tag During a Call Other Information ® 1. Press . The system responds with “Ready” The Bluetooth word mark and logos are owned by the ® Bluetooth SIG, Inc. and any use of such marks by followed by a tone.
Page 230: Before You Drive
Rear Seat Entertainment (RSE) Headphones System The RSE system includes two sets of wireless headphones. The vehicle may have a DVD Rear Seat Each set of headphones has an ON/OFF control. Entertainment (RSE) system. The RSE system An indicator light illuminates on the headphones when includes a DVD player, a video display screen, they are on.
Page 231: Stereo Rca Jacks
Stereo RCA Jacks Both sets of rear seat headphones may include foam ear pads. The RCA jacks are located behind the video screen. The foam ear pads can become worn or damaged if The RCA jacks allow audio and video signals to be they are not handled or stored properly.
Page 232: Audio Output
How to Change the Video Format when in The RSE system always transmits the audio signal to the wireless headphones, if there is audio available. the Auxiliary Mode See “Headphones” earlier in this section for more The auxiliary input video format is preset to NTSC. information.
Page 233: Dvd Player
Video Screen DVD Player The DVD player is located in the overhead console and The video screen is located in the overhead console. is controlled by the buttons on the DVD player or on To use the video screen: the remote control. See “Remote Control” later in this section for more information.
Page 234 DVD Player Buttons (Without Sunroof) (Play/Pause): Press to start play of a DVD or CD. Press while a DVD or CD is playing to pause it. Press again to continue the play of the DVD or CD. (Main DVD Menu): Press to access the DVD menu. The DVD menu is different on every DVD.
Page 235: Playing A Disc
DVD Player Buttons (With Sunroof) If a disc is already in the player, press the play/pause button on the DVD player faceplate or on the remote control. Some DVDs do not allow fast forwarding or skipping of the copyright information or the previews. Some DVDs begin playing after the previews have ﬁnished.
Page 236: Remote Control
Ejecting a Disc (DVD Player without Remote Control Sunroof) To use the remote control, aim it at the transmitter window below the video screen and press the desired Press the button on the DVD player faceplate button. Direct sunlight or very bright light can affect to eject the disc.
Page 237: Remote Control Buttons
Remote Control Buttons (Audio): Press to display a menu that only appears while a DVD is being played. The format and content of this function will vary for each disc. (Fast Reverse): Press to fast reverse the DVD or CD. To stop fast reversing, press again. This button might not work when the DVD is playing the copyright information or the previews.
Page 238 (Clear): Press within three seconds to clear a (Subtitle): Press to turn on subtitles and to move number that has been entered. through subtitle options when a DVD is playing. The format and content of this function will vary for each disc. (Illumination): Press to turn the remote control (Fast Forward): Press to fast forward the DVD or backlight on.
Page 239 Battery Replacement Problem Recommended Action To change the remote control batteries: No power. The ignition might not be in ON/RUN or 1. Remove the battery compartment door located on ACC/ACCESSORY. the bottom of the remote control. The parental control button might have been 2.
Page 240 Problem Recommended Action Problem Recommended Action In auxiliary mode, the Check the auxiliary After stopping the player, If the stop button was picture moves or scrolls. input connections at I push Play but pressed one time, the both devices. sometimes the DVD DVD player resumes Change the Video Format starts where I left off...
Page 241: Dvd Messages
DVD Messages Problem Recommended Action The following errors can display on the video screen: Sometimes the wireless Check for obstructions, headphone audio cuts out low batteries, reception Disc Format Error: This message displays if a disc is or buzzes. range, and interference inserted upside down, if the disc is not readable, or from cellular telephone towers or by using a...
Page 242: Rear Seat Audio (Rsa)
Cleaning the Video Screen Use isopropyl or rubbing alcohol on a clean cloth and gently wipe the video screen. Do not spray directly onto the screen and do not press too hard or too long on the video screen. Rear Seat Audio (RSA) This feature allows rear seat passengers to listen to any of the sources: radio, CDs, or DVDs.
Page 243: Theft-Deterrent Feature
Audio Steering Wheel Controls To scan preset stations, press and hold the SEEK button for two seconds and the radio advances to the next preset station. If the button continues to be held down, the radio advances through the available preset stations.
Page 244: Radio Reception
Radio Reception PROG (Program): Press to play a station that has been programmed on the radio preset pushbuttons. The radio seeks preset stations only with a strong Frequency interference and static can occur during signal that are in the selected band. normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external When a CD is playing in the CD changer, press this...
Page 245: Fixed Mast Antenna
XM™ Satellite Radio Service XM™ Satellite Radio Antenna System XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, The XM Satellite Radio antenna is located on the roof of and in Canada. Just as with FM, tall buildings or hills can the vehicle.
Page 246 ✍ NOTES 3-112...
Page 247: Driving Your Vehicle
Section 4 Driving Your Vehicle Your Driving, the Road, and the Vehicle ....4-2 Driving in Rain and on Wet Roads ....4-27 Driving for Better Fuel Economy .......4-2 Before Leaving on a Long Trip .......4-28 Defensive Driving ...........4-2 Highway Hypnosis ........4-28 Drunk Driving ..........4-3 Hill and Mountain Roads ........4-29 Control of a Vehicle ........4-3...
Page 248: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and Defensive Driving the Vehicle Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Driving for Better Fuel Economy Everyone on page 1-13.
Page 249: Drunk Driving
Drunk Driving For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. CAUTION: The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and Drinking and then driving is very dangerous.
Page 250: Braking
Braking Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is See Brake System Warning Light on page 3-36. a mistake. The brakes might not have time to cool Braking action involves perception time and reaction between hard stops.
Page 251: Antilock Brake System (Abs)
Antilock Brake System (ABS) Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what This vehicle has the Antilock Brake System (ABS), an happens with ABS: advanced electronic braking system that will help prevent a braking skid.
Page 252: Brake Assist
® Using ABS StabiliTrak System Do not pump the brakes. Just hold the brake pedal The vehicle has the StabiliTrak system which combines down ﬁrmly and let antilock work. The brakes might antilock brake, traction and stability control systems and vibrate or some noise might be heard, but this is normal.
Page 253 When the StabiliTrak TRACTION CONTROL OFF — The driver can modify system is both on and the engine speed management system by momentarily actively controlling the pressing the StabiliTrak button on the transmission shift stability of the vehicle, the handle. The StabiliTrak light will come on and TRACTION StabiliTrak light will blink for CONTROL OFF will be displayed.
Page 254 StabiliTrak Off snow, and you may want to “rock” the vehicle in an attempt to free it. It may also be necessary to turn off the In this mode, both stability control and part of the traction system when driving in extreme off-road conditions where control system are disabled.
Page 255 Vehicles with a DIC Vehicles without a DIC Event StabiliTrak system activates using engine speed management, brake Blinking StabiliTrak Active Blinking traction control, and/or stability control. Service StabiliTrak system is disabled due to Solid Solid Solid StabiliTrak a system fault. StabiliTrak Not StabiliTrak system is disabled due to Solid...
Page 256: Power Steering
Steering If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, see your dealer/retailer for service. Power Steering Adding non-GM accessories can affect the vehicle’s If power steering assist is lost because the engine stops performance.
Page 257: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 258: Off-Road Recovery
Off-Road Recovery Passing The vehicle’s right wheels can drop off the edge of a Passing another vehicle on a two-lane road can be road onto the shoulder while driving. dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass.
Page 259 Skidding Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, slow In a skid, a driver can lose control of the vehicle. down and adjust your driving to these conditions. It is Defensive drivers avoid most skids by taking reasonable important to slow down on slippery surfaces because care suited to existing conditions, and by not overdriving...
Page 260: Competitive Driving
Competitive Driving Off-Road Driving See your warranty book before using your vehicle for Vehicles with four-wheel drive can be used for off-road competitive driving. After reviewing your warranty book, driving. Vehicles without four-wheel drive should not please see the GM Performance Parts website or catalog be driven off-road except on a level, solid surface.
Page 261 Before You Go Off-Roading Off-roading can be great fun but has some deﬁnite hazards. The greatest of these is the terrain itself. When • Have all necessary maintenance and service off-road driving, traffic lanes are not marked, curves are work done. not banked, and there are no road signs.
Page 262 Loading Your Vehicle for Off-Road CAUTION: (Continued) Driving • Heavy loads on the roof raise the vehicle’s CAUTION: center of gravity, making it more likely to roll over. You can be seriously or fatally injured if the vehicle rolls over. Put heavy loads inside •...
Page 263: Environmental Concerns
Environmental Concerns Traveling to Remote Areas Off-road driving can provide wholesome and satisfying It makes sense to plan your trip, especially when going recreation. However, it also raises environmental to a remote area. Know the terrain and plan your route. concerns.
Page 264: Scanning The Terrain
Scanning the Terrain Controlling the vehicle is the key to successful off-road driving. One of the best ways to control the vehicle Off-road driving can take you over many different kinds is to control the speed. At higher speeds: of terrain. Be familiar with the terrain and its many •...
Page 265: Driving On Hills
Driving on Hills When driving over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs, or other surface Off-road driving often takes you up, down, or across a features can jerk the wheel out of your hands. hill.
Page 266: Approaching A Hill
Approaching a Hill Driving Uphill When you approach a hill, decide if it is too steep to Once you decide it is safe to drive up the hill: climb, descend, or cross. Steepness can be hard • Use a low gear and get a ﬁrm grip on the steering to judge.
Page 267 • If the vehicle stalls, or is about to stall, and you cannot Attach a ﬂag to the vehicle to be more visible to make it up the hill: approaching traffic on trails or hills. • Push the brake pedal to stop the vehicle and keep •...
Page 268: Driving Downhill
Things not to do if the vehicle stalls, or is about to stall, when going up a hill: CAUTION: • Never attempt to prevent a stall by shifting into N (Neutral) to rev-up the engine and regain forward Shifting the transfer case to Neutral can cause your momentum.
Page 269 If you decide you can go down a hill safely, try to keep Things not to do when driving down a hill: the vehicle headed straight down. Use a low gear • When driving downhill, avoid turns that take you so engine drag can help the brakes so they do not across the incline of the hill.
Page 270: Driving Across An Incline
Driving Across an Incline • Surface conditions can be a problem. Loose gravel, muddy spots, or even wet grass can cause the An off-road trail will probably go across the incline of a tires to slip sideways, downhill. If the vehicle slips hill.
Page 271: Stalling On An Incline
Stalling on an Incline When driving on sand, wheel traction changes. On loosely packed sand, such as on beaches or sand dunes, the tires will tend to sink into the sand. This affects steering, accelerating, and braking. Drive at a CAUTION: reduced speed and avoid sharp turns or abrupt maneuvers.
Page 272: Driving In Water
Driving in Water If the water is not too deep, drive slowly through it. At faster speeds, water splashes on the ignition system and the vehicle can stall. Stalling can also occur if you get the tailpipe under water. If the tailpipe is under water, you will CAUTION: never be able to start the engine.
Page 273: Driving At Night
Driving at Night Driving in Rain and on Wet Roads Night driving is more dangerous than day driving because Rain and wet roads can reduce vehicle traction some drivers are likely to be impaired — by alcohol or and affect your ability to stop and accelerate. Always drugs, with night vision problems, or by fatigue.
Page 274: Before Leaving On A Long Trip
Hydroplaning Before Leaving on a Long Trip Hydroplaning is dangerous. Water can build up under To prepare your vehicle for a long trip, consider having your vehicle’s tires so they actually ride on the water. This it serviced by your dealer/retailer before departing. can happen if the road is wet enough and you are going Things to check on your own include: fast enough.
Page 275: Hill And Mountain Roads
Hill and Mountain Roads CAUTION: Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: Coasting downhill in N (Neutral) or with the ignition • off is dangerous. The brakes will have to do all the Keep the vehicle serviced and in good shape.
Page 276: Winter Driving
Winter Driving Blizzard Conditions Being stuck in snow can be in a serious situation. Stay Driving on Snow or Ice with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-7. Drive carefully when there is snow or ice between the To get help and keep everyone in the vehicle safe: tires and the road, creating less traction or grip.
Page 277 Run the engine for short periods only as needed to keep warm, but be careful. CAUTION: (Continued) To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine • Open a window about two inches (5 cm) on off and close the window most of the way to save heat.
Page 278: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
If Your Vehicle is Stuck in Sand, Rocking Your Vehicle to Get It Out Mud, Ice, or Snow Turn the steering wheel left and right to clear the area around the front wheels. For four-wheel-drive vehicles, Slowly and cautiously spin the wheels to free the ®...
Page 279: Loading The Vehicle
Loading the Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 280 Tire and Loading Information Label The Tire and Loading Information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds. The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inﬂation pressures (D).
Page 281 Steps for Determining Correct Load Limit Determine the combined weight of luggage and cargo being loaded on the vehicle. That Locate the statement “The combined weight weight may not safely exceed the available of occupants and cargo should never exceed cargo and luggage load capacity calculated XXX kg or XXX lbs”...
Page 282 Example 1 Example 2 Item Description Total Item Description Total Vehicle Capacity Vehicle Capacity 1,000 lbs 1,000 lbs Weight for Weight for (453 kg) (453 kg) Example 1 = Example 2 = Subtract Occupant Subtract Occupant Weight 150 lbs 300 lbs (136 kg) Weight 150 lbs 750 lbs (136 kg) (68 kg) ×...
Page 283 Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. Your vehicle may have an electronically controlled air suspension system that automatically keeps your vehicle level as you load and unload your vehicle.
Page 284 Certiﬁcation/Tire Label To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline.
Page 285: Adding A Snow Plow Or Similar Equipment
Using heavier suspension components to get added durability might not change your vehicle’s CAUTION: (Continued) weight ratings. Ask your dealer to help you load your vehicle the right way. • Do not leave an unsecured child restraint Notice Overloading your vehicle may cause in your vehicle.
Page 286: Towing
Towing Here are some important things to consider before recreational vehicle towing: • What is the towing capacity of the towing vehicle? Towing Your Vehicle Be sure to read the tow vehicle manufacturer’s recommendations. To avoid damage, the disabled vehicle should be towed •...
Page 287: Dinghy Towing
All-Wheel-Drive Vehicles Dinghy Towing (TrailBlazer SS) Two-Wheel-Drive Vehicles Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
Page 288 Four-Wheel-Drive Vehicles Use the following procedure to dinghy tow a four-wheel-drive vehicle: 1. Position the vehicle being towed behind the tow vehicle and shift the transmission to P (Park). 2. Turn the engine off, but leave the ignition in the ACC/ACCESSORY position.
Page 289: Dolly Towing
Dolly Towing CAUTION: Front Towing (Front Wheels Off the Ground) Shifting a four-wheel-drive vehicle’s transfer case Two-Wheel-Drive Vehicles into N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). The driver or others could be injured. Make sure the parking brake is ﬁrmly set before the transfer case is shifted to N (Neutral).
Page 290 Four-Wheel-Drive Vehicles CAUTION: Shifting a four-wheel-drive vehicle’s transfer case into N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). The driver or others could be injured. Make sure the parking brake is ﬁrmly set before the transfer case is shifted to N (Neutral).
Page 291 Rear Towing (Rear Wheels Off Two-Wheel-Drive Vehicles the Ground) Use the following procedure to dolly tow a two-wheel-drive vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer’s instructions. 2. Drive the rear wheels onto the dolly. 3.
Page 292 Four-Wheel-Drive Vehicles CAUTION: Use the following procedure to dolly tow a four-wheel-drive vehicle from the rear: 1. Attach the dolly to the tow vehicle following the Shifting a four-wheel-drive vehicle’s transfer case dolly manufacturer’s instructions. into N (Neutral) can cause the vehicle to roll even 2.
Page 293: Indicator Light
Electronically Controlled Air Overload Protection Suspension System The air suspension system is equipped with overload protection. Overload protection is designed to protect With this feature, an electronically controlled air the air suspension system, and it is an indicator to the suspension system automatically keeps the vehicle level driver that the vehicle is overloaded.
Page 294: Towing A Trailer
Towing a Trailer Notice: Pulling a trailer improperly can damage the vehicle and result in costly repairs not covered by the vehicle warranty. To pull a trailer correctly, follow the advice in this section and see your CAUTION: dealer/retailer for important information about towing a trailer with the vehicle.
Page 295: Pulling A Trailer
Pulling A Trailer Three important considerations have to do with weight: • The weight of the trailer Here are some important points: • The weight of the trailer tongue • There are many different laws, including speed limit • restrictions, having to do with trailering. Make sure The weight on the vehicle’s tires the rig will be legal, not only where you live but Weight of the Trailer...
Page 296 Look in the following chart to ﬁnd the maximum trailer weight for the vehicle. Vehicle Axle Ratio Max. Trailer Wt. *GCWR 3.42 5,400 lbs (2 449 kg) 10,000 lbs (4 536 kg) 2WD TrailBlazer (4.2 L L6 Engine) 3.73 5,900 lbs (2 676 kg) 10,500 lbs (4 763 kg) 4.10 6,400 lbs (2 903 kg)
Page 297: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 298 Do not exceed the maximum allowable tongue weight Consider the following example: for the vehicle. Choose the shortest hitch extension that A vehicle model base weight is 5,500 lbs (2 495 kg); will position the hitch ball closest to the vehicle. This 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs will help reduce the effect of trailer tongue weight on the (1 225 kg) at the rear axle.
Page 299 If the vehicle has many options and there is a front seat Since tongue weight is usually at least 10 percent of total passenger and two rear seat passengers with some loaded trailer weight, expect that the largest trailer the luggage and gear in the vehicle as well.
Page 300: Safety Chains
Weight Distributing Hitches and Weight If pulling a trailer that, when loaded, will weigh more than 4,000 lbs (1 814 kg) be sure to use a properly mounted Carrying Hitches weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving.
Page 301: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer. And always keep in mind CAUTION: that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
Page 302: Driving On Grades
Backing Up When towing a trailer, the arrows on the instrument panel ﬂash for turns even if the bulbs on the trailer are burned Hold the bottom of the steering wheel with one hand. out. For this reason you may think other drivers are Then, to move the trailer to the left, move that hand seeing the signal when they are not.
Page 303: Parking On Hills
Parking on Hills CAUTION: CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking Parking the vehicle on a hill with the trailer attached brake ﬁrmly set. The vehicle can roll. can be dangerous.
Page 304: Trailer Wiring Harness
Leaving After Parking on a Hill Trailer Wiring Harness 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 305 The seven-wire harness contains the following trailer The vehicle may be equipped with a four-pin trailer circuits: towing harness. This harness has a four-pin trailer connector that contains the following trailer circuits: • Yellow: Left Stop/Turn Signal • Yellow: Left Stop/Turn Signal •...
Page 306 ✍ NOTES 4-60...
Page 307: Service And Appearance Care
Section 5 Service and Appearance Care Service ............5-3 Engine Fan Noise .........5-36 Accessories and Modiﬁcations ......5-3 Power Steering Fluid ........5-37 California Proposition 65 Warning .....5-4 Windshield Washer Fluid ........5-38 California Perchlorate Materials Requirements ..5-4 Brakes ............5-39 Doing Your Own Service Work ......5-4 Battery ............5-42 Adding Equipment to the Outside of Jump Starting ..........5-43...
Page 308 Section 5 Service and Appearance Care Tire Pressure Monitor Operation .....5-69 Care of Safety Belts ........5-112 Tire Inspection and Rotation ......5-73 Weatherstrips ..........5-112 When It Is Time for New Tires .......5-74 Washing Your Vehicle ........5-113 Buying New Tires .........5-75 Cleaning Exterior Lamps/Lenses ....5-113 Different Size Tires and Wheels ......5-77 Finish Care ..........5-114 Uniform Tire Quality Grading ......5-78...
Page 309: Service
Service Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added For service and parts needs, visit your dealer/retailer. to the vehicle, they can affect vehicle performance and You will receive genuine GM parts and GM-trained safety, including such things as airbags, braking, stability, and supported service people.
Page 310: California Proposition 65 Warning
California Proposition 65 Warning Doing Your Own Service Work Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause CAUTION: cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some You can be injured and the vehicle could be component wear by-products contain and/or emit...
Page 311: Adding Equipment To The Outside Of The Vehicle
Fuel If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order Use of the recommended fuel is an important part of the proper service manual, see Service Publications the proper maintenance of this vehicle.
Page 312: Gasoline Octane
Gasoline Octane Gasoline Speciﬁcations If the vehicle has the 4.2L L6 engine (VIN Code S) or At a minimum, gasoline should meet ASTM speciﬁcation the 5.3L V8 engine (VIN Code M), use regular unleaded D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in gasoline with a posted octane rating of 87 or higher.
Page 313: Additives
Additives Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl To provide cleaner air, all gasolines in the United States (MMT); ask the attendant where you buy gasoline are now required to contain additives that help prevent whether the fuel contains MMT.
Page 314: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling.
Page 315 There may also be a light that comes on in the instrument panel to let you know if the gas cap is CAUTION: not properly installed. See Check Gas Cap Light on page 3-47 for more information. Fuel can spray out on you if you open the fuel cap too quickly.
Page 316: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood CAUTION: CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the Things that burn can get on hot engine parts and container can ignite the fuel vapor. You can be start a ﬁre.
Page 317: Hood Release
Hood Release To open the hood: 1. Pull the handle with this symbol on it. It is located inside the vehicle under the instrument panel on the driver side. 2. Then go to the front of the vehicle and release the secondary hood release.
Page 318: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 4.2L L6 engine, here is what you will see: 5-12...
Page 319 A. Engine Air Cleaner/Filter. See Engine Air G. Radiator Pressure Cap. See Radiator Pressure Cap Cleaner/Filter on page 5-24. on page 5-34. B. Engine Coolant Recovery Tank. See Cooling System H. Engine Oil Fill Cap. See “When to Add Engine Oil” on page 5-28.
Page 320 When you open the hood on the 5.3L V8 engine, here is what you will see: 5-14...
Page 321 A. Engine Coolant Recovery Tank. See Cooling System G. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-28. on page 5-34. B. Engine Air Cleaner/Filter. See Engine Air H. Remote Negative (−) Terminal (Marked GND). Cleaner/Filter on page 5-24. See Jump Starting on page 5-43.
Page 322 When you open the hood on the 6.0L V8 TrailBlazer SS engine, here is what you will see: 5-16...
Page 323 A. Engine Coolant Recovery Tank. See Cooling System G. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-28. on page 5-34. B. Engine Air Cleaner/Filter. See Engine Air H. Remote Negative (−) Terminal (Marked GND). Cleaner/Filter on page 5-24. See Jump Starting on page 5-43.
Page 324: Engine Oil
Engine Oil When to Add Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 325 Notice: Do not add too much oil. If the engine See Engine Compartment Overview on page 5-12 for has so much oil that the oil level gets above the the location of the engine oil ﬁll cap. cross-hatched area (F) that shows the proper Add enough oil to put the level somewhere in the proper operating range for the L6 engine or above the operating range.
Page 326: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers Except Vehicles with 6.0L V8 (VIN Code H) on an oil container show its viscosity, or thickness. Engine Do not use other viscosity oils such as SAE 20W-50. •...
Page 327 For 6.0L V8 (VIN Code H) Engine Notice: Using oils that do not have the GM4718M Standard designation can cause engine damage not Vehicles Only covered by the vehicle warranty. Look for three things: • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness.
Page 328: Engine Oil Life System
Engine Oil Life System Substitute Engine Oil: When adding oil to maintain engine oil level, oil meeting GM Standard GM4718M When to Change Engine Oil might not be available. You can add substitute oil designated SAE 5W-30 with the starburst symbol at all This vehicle has a computer system that indicates when temperatures.
Page 329: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life What to Do with Used Oil System Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. The Engine Oil Life System calculates when to change Do not let used oil stay on your skin for very long.
Page 330: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter How to Inspect the Engine Air Cleaner/Filter See Engine Compartment To inspect the air cleaner/ﬁlter remove the ﬁlter from the Overview on page 5-12 vehicle and lightly shake the ﬁlter to release loose dust for the location of the and dirt.
Page 331: Automatic Transmission Fluid
Automatic Transmission Fluid CAUTION: When to Check and Change Automatic Transmission Fluid Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air A good time to check the automatic transmission ﬂuid level is when the engine oil is changed. cleaner not only cleans the air;...
Page 332: How To Check Automatic Transmission Fluid
How to Check Automatic Transmission To get the right reading, the ﬂuid should be at normal operating temperature, which is 180°F to 200°F Fluid (82°C to 93°C). Because this operation can be a little difficult, you may Get the vehicle warmed up by driving about choose to have this done at the dealer/retailer service 15 miles (24 km) when outside temperatures are department.
Page 333 Checking the Fluid Level 2. Reinstall it back in all the way, wait three seconds and then pull it back out again. If the dipstick does Prepare the vehicle as follows: not go down the tube easily, turn the blade and try again until it is fully inserted in the tube.
Page 334: Cooling System
How to Add Automatic Transmission Cooling System Fluid The cooling system allows the engine to maintain the correct working temperature. Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. Add ﬂuid only after checking the transmission ﬂuid while it is hot.
Page 335: Engine Coolant
® Notice: Using coolant other than DEX-COOL cause premature engine, heater core, or radiator CAUTION: corrosion. In addition, the engine coolant could require changing sooner, at 30,000 miles (50 000 km) or 24 months, whichever occurs ﬁrst. Any repairs An electric engine cooling fan under the hood can would not be covered by the vehicle warranty.
Page 336: What To Use
What to Use Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: Gives freezing protection down to −34°F (−37°C), • CAUTION: outside temperature. • Gives boiling protection up to 265°F (129°C), Adding only plain water to the cooling system can engine temperature.
Page 337: Checking Coolant
Checking Coolant How to Add Coolant to the Recovery Tank The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery CAUTION: tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
Page 338: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done. CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury.
Page 339 3. Fill the radiator with the proper DEX-COOL coolant 4. Then ﬁll the coolant recovery tank to the mixture, up to the base of the ﬁller neck. See Engine FULL COLD mark. Coolant on page 5-29 for more information about the 5.
Page 340: Radiator Pressure Cap
8. Then replace the pressure cap. At any time during this procedure if coolant begins to ﬂow out of the ﬁller neck, reinstall the pressure cap. Be sure the pressure cap is hand-tight and fully seated. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur.
Page 341: Engine Overheating
Engine Overheating If Steam Is Coming From The Engine Compartment The vehicle has several indicators to warn of engine overheating. You will ﬁnd a coolant temperature gage on the vehicle’s CAUTION: instrument panel. See Engine Coolant Temperature Gage on page 3-38 for more information. Steam from an overheated engine can burn you If the vehicle has a Driver Information Center (DIC), badly, even if you just open the hood.
Page 342: If No Steam Is Coming From The Engine Compartment
If No Steam Is Coming From The vehicle distance from the car in front of you. If the warning does not come back on, continue to drive Engine Compartment normally. If an engine overheat warning is displayed but no If the warning continues, pull over, stop, and park the steam can be seen or heard, the problem may not be vehicle right away.
Page 343: Power Steering Fluid
Power Steering Fluid How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: See Engine Compartment 1. Turn the key off and let the engine compartment Overview on page 5-12 for cool down. reservoir location. 2.
Page 344: Windshield Washer Fluid
Windshield Washer Fluid Notice: • When using concentrated washer ﬂuid, follow What to Use the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer ﬂuid. When the vehicle needs windshield washer ﬂuid, be Water can cause the solution to freeze and sure to read the manufacturer’s instructions before use.
Page 345: Brakes
Brakes Do not top off the brake ﬂuid. Adding ﬂuid does not correct a leak. If ﬂuid is added when the linings are worn, there will be too much ﬂuid when new brake Brake Fluid linings are installed. Add or remove brake ﬂuid, as necessary, only when work is done on the brake The brake master cylinder hydraulic system.
Page 346: Checking Brake Fluid
Checking Brake Fluid CAUTION: Check brake ﬂuid by looking at the brake ﬂuid reservoir. See Engine Compartment Overview on page 5-12. With the wrong kind of ﬂuid in the brake hydraulic The ﬂuid level should be system, the brakes might not work well. This could above MIN.
Page 347: Brake Adjustment
Brake Wear Some driving conditions or climates can cause a brake squeal when the brakes are ﬁrst applied or lightly applied. This vehicle has disc brakes. Disc brake pads have This does not mean something is wrong with the brakes. built-in wear indicators that make a high-pitched warning Properly torqued wheel nuts are necessary to help sound when the brake pads are worn and new pads...
Page 348: Battery
Replacing Brake System Parts Vehicle Storage The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if CAUTION: the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced —...
Page 349: Jump Starting
Jump Starting Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start Trying to start the vehicle by pushing or pulling it your vehicle.
Page 350 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could CAUTION: be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. Using a match near a battery can cause battery 3.
Page 351 6. Connect the red positive (+) cable to the CAUTION: positive (+) terminal of the dead battery. Use a remote positive (+) Fans or other moving engine parts can injure you terminal if the vehicle badly. Keep your hands away from moving parts has one.
Page 352 9. Connect the other end of the negative (−) cable to the remote negative (−) terminal on the vehicle with the dead battery. 10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service.
Page 353 To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 354: All-Wheel Drive
All-Wheel Drive If the level is below the bottom of the ﬁller plug hole, located on the transfer case, you’ll need to add some lubricant. Add enough lubricant to raise the level to the When to Check Lubricant bottom of the ﬁller plug hole. Use care not to overtighten the plug.
Page 355: Rear Axle
Rear Axle For all vehicles, excluding vehicles equipped with the 6.0L V8 Engine, the proper level is from 0 to 0.40 inch (0 to 10 mm) below the bottom of the ﬁller plug hole, When to Check Lubricant located on the rear axle. It is not necessary to regularly check rear axle ﬂuid For vehicles equipped with the 6.0L V8 Engine, the unless you suspect there is a leak or you hear an...
Page 356: Four-Wheel Drive
Four-Wheel Drive If the level is below the bottom of the ﬁller plug hole, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller Transfer Case plug hole. Use care not to overtighten the plug. When to Check Lubricant What to Use It is not necessary to regularly check ﬂuid unless you...
Page 357: Front Axle
Front Axle If the level is below the bottom of the ﬁller plug hole, located on the front axle, you may need to add some lubricant. When to Check Lubricant When the differential is cold, add enough lubricant It is not necessary to regularly check front axle ﬂuid to raise the level to 0.50 inch (12 mm) below the ﬁller unless you suspect there is a leak or you hear an plug hole.
Page 358: Headlamp Aiming
Headlamp Aiming Halogen Bulbs Headlamp aim has been preset at the factory and should need no further adjustment. CAUTION: However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the Halogen bulbs have pressurized gas inside and low-beam headlamps may be necessary if oncoming can burst if you drop or scratch the bulb.
Page 359: Taillamps And Turn Signal Lamps
Taillamps and Turn Signal Lamps 1. Open the liftgate. See Liftgate/Liftglass on page 2-13. 2. Remove the two screws from the taillamp assembly. 4. Unclip the wiring harness (A) and remove the three retaining screws (B) from the socket plate. 5.
Page 360: License Plate Lamp
License Plate Lamp 3. Pull the old bulb straight out from the bulb socket. 4. Push the new bulb into the socket until it clicks. 1. Remove the two screws holding the license plate 5. Replace the lamp assembly lens and tighten lamp lens.
Page 361: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-4. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by your warranty.
Page 362 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the A. Claw in Notch blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully B.
Page 363: Backglass Wiper Blade Replacement
Backglass Wiper Blade Replacement 3. Rotate the wiper blade assembly, and pull it off of the wiper arm. Hold the wiper arm in position and push the blade away from the wiper arm. 1. Lift the wiper blade assembly up and out of the park rest position.
Page 364: Tires
Tires CAUTION: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever • Underinﬂated tires pose the same danger have questions about your tire warranty and where as overloaded tires. The resulting accident to obtain service, see your vehicle Warranty booklet could cause serious injury.
Page 365: Winter Tires
Low-Proﬁle Performance Tire Winter Tires If your vehicle has P255/50R20 size tires, they are For cold weather driving conditions you may prefer to classiﬁed as low-proﬁle performance tires. These get tires designed for snow or ice, if your vehicle has tires are designed for very responsive driving on P255/50R20 size tires.
Page 366: Tire Sidewall Labeling
Tire Sidewall Labeling (B) TPC Spec (Tire Performance Criteria Speciﬁcation) Original equipment tires designed to GM’s speciﬁc tire performance criteria have a Useful information about a tire is molded into the TPC speciﬁcation code molded onto the sidewall. sidewall. The following illustration is an example GM’s TPC speciﬁcations meet or exceed all federal of a typical P-Metric tire sidewall.
Page 367 (G) Maximum Cold Inﬂation Load Limit (B) Tire Width The three-digit number indicates Maximum load that can be carried and the the tire section width in millimeters from sidewall maximum pressure needed to support that load. to sidewall. For information on recommended tire pressure (C) Aspect Ratio A two-digit number that see Inﬂation - Tire Pressure on page 5-65...
Page 368: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Cold Tire Pressure The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat Air Pressure The amount of air inside the from driving.
Page 369 Intended Outboard Sidewall The side of an Normal Occupant Weight The number of asymmetrical tire, that must always face outward occupants a vehicle is designed to seat multiplied when mounted on a vehicle. by 150 lbs (68 kg). See Loading the Vehicle on page 4-33.
Page 370 Radial Ply Tire A pneumatic tire in which the UTQGS (Uniform Tire Quality Grading ply cords that extend to the beads are laid at Standards) A tire information system that 90 degrees to the centerline of the tread. provides consumers with ratings for a tire’s traction, temperature, and treadwear.
Page 371: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure A vehicle speciﬁc Tire and Loading Information label is attached to your vehicle. This label shows your vehicle’s original equipment tires and the Tires need the correct amount of air pressure to correct inﬂation pressures for your tires when they operate effectively.
Page 372: How To Check
How to Check High-Speed Operation Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly CAUTION: inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are underinﬂated.
Page 373: Tire Pressure Monitor System
Tire Pressure Monitor System If your vehicle has P255/50R20 104V size tires installed on the rear axle, they will require inﬂation pressure adjustment when driving your vehicle at speeds above The Tire Pressure Monitor System (TPMS) uses radio 99 mph (160 km/h). Set the cold inﬂation pressure, for the and sensor technology to check tire pressure levels.
Page 374 Federal Communications Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to Commission (FCC) and maintain correct tire pressure, even if under-inﬂation Industry and Science Canada has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Page 375: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation At the same time a message to check the pressure in a speciﬁc tire appears on the Driver Information Center (DIC) display. The low tire pressure warning light and the This vehicle may have a Tire Pressure Monitor System DIC warning message come on at each ignition cycle (TPMS).
Page 376: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message Your vehicle’s TPMS can alert you about a low tire pressure condition but it does not replace normal tire The TPMS will not function properly if one or more of maintenance. See Tire Inspection and Rotation on the TPMS sensors are missing or inoperable.
Page 377: Tpms Sensor Matching Process
• TPMS Sensor Matching Process One or more TPMS sensors are missing or damaged. The DIC message and the TPMS Each TPMS sensor has a unique identiﬁcation code. malfunction light should go off when the TPMS Any time you rotate your vehicle’s tires or replace one sensors are installed and the sensor matching or more of the TPMS sensors, the identiﬁcation codes process is performed successfully.
Page 378 You have two minutes to match the ﬁrst tire/wheel The single horn chirp should sound within position, and ﬁve minutes overall to match all four 15 seconds, conﬁrming that the sensor identiﬁcation tire/wheel positions. If it takes longer than two minutes, to code has been matched to this tire and wheel match the ﬁrst tire and wheel, or more than ﬁve minutes position.
Page 379: Tire Inspection And Rotation
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, if the vehicle has one, for signs of wear or damage. See When It Is Time for New Tires on page 5-74 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Page 380: When It Is Time For New Tires
When It Is Time for New Tires Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-69. Various factors, such as maintenance, temperatures, Make certain that all wheel nuts are properly driving speeds, vehicle loading, and road conditions, tightened.
Page 381: Buying New Tires
Buying New Tires You need new tires if any of the following statements are true: GM has developed and matched speciﬁc tires for • You can see the indicators at three or more places your vehicle. The original equipment tires installed around the tire.
Page 382 GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires CAUTION: will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking If you use bias-ply tires on the vehicle, the and handling performance of your vehicle.
Page 383: Different Size Tires And Wheels
Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. CAUTION: See Loading the Vehicle on page 4-33, for more information about the Tire and Loading Information Label and its location on your vehicle. If you add different sized wheels, your vehicle may not provide an acceptable level of performance and Different Size Tires and Wheels safety if tires not recommended for those wheels...
Page 384: Uniform Tire Quality Grading
Uniform Tire Quality Grading While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform Quality grades can be found where applicable on to federal safety requirements and additional the tire sidewall between tread shoulder and General Motors Tire Performance Criteria (TPC) maximum section width.
Page 385 Traction – AA, A, B, C Temperature – A, B, C The traction grades, from highest to lowest, are The temperature grades are A (the highest), B, AA, A, B, and C. Those grades represent the tire’s and C, representing the tire’s resistance to the ability to stop on wet pavement as measured under generation of heat and its ability to dissipate heat controlled conditions on speciﬁed government test...
Page 386: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest If you need to replace any of your wheels, wheel bolts, tire life and best overall performance.
Page 387: Tire Chains
Tire Chains Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain CAUTION: clearance to the body and chassis. See Changing a Flat Tire on page 5-93 for more Do not use tire chains.
Page 388: If A Tire Goes Flat
If a Tire Goes Flat CAUTION: It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak Lifting a vehicle and getting under it to do out slowly.
Page 389: Tire Sealant And Compressor Kit
Tire Sealant and Compressor Kit CAUTION: CAUTION: Over-inﬂating a tire could cause the tire to rupture and you or others could be injured. Be sure to Idling a vehicle in an enclosed area with poor read and follow the tire sealant and compressor kit ventilation is dangerous.
Page 390 The tire sealant and compressor can be used to This vehicle may have one of the following tire sealant temporarily seal punctures up to ⁄ inch (6 mm) in and compressor kits. The kit includes: the tread area of the tire. It can also be used to inﬂate an under inﬂated tire.
Page 391: Tire Sealant
Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer.
Page 392: Punctured Tire
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inﬂate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes.
Page 393 3. Place the kit on the ground. dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inﬂates Make sure the tire valve stem is positioned close to with air only. the ground so the hose will reach it. 10.
Page 394 12. Unplug the power plug (H) from the accessory 19. Stop at a safe location and check the tire pressure. power outlet in the vehicle. Refer to Steps 1 through 11 under “Using the Tire Sealant and Compressor Kit without Sealant to 13.
Page 395: Not Punctured
Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured) To use the air compressor to inﬂate a tire with air only and not sealant: Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-82.
Page 396 4. Remove the tire valve stem cap from the ﬂat tire by 10. Inﬂate the tire to the recommended inﬂation turning it counterclockwise. pressure using the pressure gage (C). The recommended inﬂation pressure can be found 5. Attach the air only hose (G) onto the tire valve stem on the Tire and Loading Information label.
Page 397: Removal And Installation Of The Sealant Canister
Removal and Installation of the Sealant 12. Unplug the power plug (H) from the accessory power outlet in the vehicle. Canister 13. Disconnect the air only hose (G) from the tire valve To remove the sealant canister: stem, by turning it counterclockwise, and replace the tire valve stem cap.
Page 398: Tire Sealant And Compressor Kit Storage
Tire Sealant and Compressor Kit 3. Remove the straps. Storage The tire sealant and compressor kit is located in the ﬂoor storage compartment at the rear of the vehicle. 1. Open the liftgate. See Liftgate/Liftglass on page 2-13. 2. Open the rear ﬂoor storage lid. See Rear Floor Storage Cover on page 2-55.
Page 399: Changing A Flat Tire
Changing a Flat Tire CAUTION: (Continued) If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard 5. Do not allow passengers to remain in the warning ﬂashers. See Hazard Warning Flashers vehicle.
Page 400: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The tools you will be using include: A. Wheel Wrench D. Handle (Jack End) B. Wheel Blocks E. Jack C. Extension(s) (Socket End) The jacking equipment needed to remove the spare tire is stored under the rear seat. To release the jack from its holder, turn the knob on the jack counterclockwise to lower the jack head.
Page 401 To remove the underbody-mounted spare from your 3. Insert the socket end vehicle: of the extension (C) on a 45 degree angle Notice: If you remove or restow a tire from/to downward into the hoist the storage position under the vehicle while it is drive shaft hole.
Page 402 5. Tilt the retainer at the end of the cable when the 4. Turn the wheel wrench counterclockwise to lower tire has been completely lowered, and pull it the spare tire. Keep turning the wheel wrench until through the wheel opening. the spare tire can be pulled out from under the vehicle.
Page 403: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and 3. Using the wheel Installing the Spare Tire wrench, loosen all the wheel nuts by turning 1. Do a safety check before proceeding. See Changing the nuts one turn a Flat Tire on page 5-93 for more information. counterclockwise.
Page 404 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. Front Position Rear Position CAUTION: A.
Page 405 8. Remove all the wheel nuts and the ﬂat tire. 7. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the spare tire to ﬁt. 5-99...
Page 406 9. Remove any rust or dirt from the wheel bolts, CAUTION: mounting surfaces and spare wheel. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident.
Page 407 CAUTION: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 11. Put the nuts on by hand. Make sure the cone shaped end is toward the wheel. 12.
Page 408 Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid CAUTION: expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. See Capacities and Speciﬁcations on Incorrect wheel nuts or improperly tightened wheel page 5-125 for the wheel nut torque speciﬁcation.
Page 409: Secondary Latch System
Secondary Latch System CAUTION: This vehicle may have an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire, if the vehicle has one, Someone standing too close during the procedure from suddenly falling off the vehicle if the cable holding could be injured by the jack.
Page 410 2. If visible, ﬁrst try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable. 3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4.
Page 411 9. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. 10. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while ﬁrmly pulling the jack out from under the spare tire with the other hand.
Page 412: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and CAUTION: Tools The underbody-mounted spare tire needs to be CAUTION: stored with the valve stem pointing up. If the spare tire is stored with the valve stem pointing downward, its secondary latch will not work Storing a jack, a tire, or other equipment in the properly and the spare tire could loosen and passenger compartment of the vehicle could...
Page 413 Follow this diagram to store the underbody-mounted ﬂat 3. Make sure the valve stem is pointed up and to or spare tire. the rear. A. Wheel Wrench 4. Pull the retainer (D) through the wheel. B. Hoist Shaft 5. Put the socket end of the extension (C) through the hole just above the rear bumper at a 45 degree C.
Page 414 A. Handle D. Extension(s) 7. Make sure the tire is stored securely. Push, pull (A), B. Wheel Wrench E. Knob and then try to turn (B) the tire. If the tire moves, C. Instruction Label F. Wheel Blocks and Jack use the wheel wrench and socket end of the extension to tighten the cable.
Page 415: Spare Tire
Spare Tire Appearance Care This vehicle may have a spare tire. Although the Interior Cleaning spare tire was fully inﬂated when the vehicle was new, it can lose air after a time. Check the inﬂation pressure The vehicle’s interior will continue to look its best if it is regularly.
Page 416 When cleaning the vehicle’s interior, only use cleaners Products that remove odors from the vehicle’s speciﬁcally designed for the surfaces being cleaned. upholstery and clean the vehicle’s glass can be Permanent damage may result from using cleaners on obtained from your dealer/retailer. surfaces for which they were not intended.
Page 417: Fabric/Carpet
Fabric/Carpet If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small Use a vacuum cleaner with a soft brush attachment hidden area for colorfastness ﬁrst.
Page 418: Instrument Panel, Vinyl, And Other Plastic Surfaces
Instrument Panel, Vinyl, and Other Care of Safety Belts Plastic Surfaces Keep belts clean and dry. A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, CAUTION: a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Page 419: Washing Your Vehicle
Washing Your Vehicle Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. The best way to preserve the vehicle’s ﬁnish is to keep it clean by washing it often.
Page 420: Finish Care
Finish Care Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep Occasional waxing or mild polishing of the vehicle their luster. Washing with water is all that is usually by hand may be necessary to remove residue from needed.
Page 421: Aluminum Wheels
Aluminum Wheels cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: Using strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain Notice: Driving the vehicle through an automatic acid on aluminum or chrome-plated wheels, could car wash that has silicone carbide tire cleaning damage the surface of the wheel(s).
Page 422: Sheet Metal Damage
Sheet Metal Damage Underbody Maintenance If the vehicle is damaged and requires sheet metal Chemicals used for ice and snow removal and dust repair or replacement, make sure the body repair control can collect on the underbody. If these are not shop applies anti-corrosion material to parts repaired removed, corrosion and rust can develop on the or replaced to restore corrosion protection.
Page 423: Vehicle Identiﬁcation
Vehicle Identiﬁcation Engine Identiﬁcation The eighth character in the VIN is the engine code. This code helps identify the vehicle’s engine, speciﬁcations, Vehicle Identiﬁcation Number (VIN) and replacement parts. See “Engine Speciﬁcations” under Capacities and Speciﬁcations on page 5-125 for your vehicle’s engine code.
Page 424: Electrical System
Electrical System Windshield Wiper Fuses The windshield wiper motor is protected by a circuit Add-On Electrical Equipment breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, Notice: Do not add anything electrical to the have it ﬁxed.
Page 425: Fuses And Circuit Breakers
Fuses and Circuit Breakers Engine Compartment Fuse Block The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of ﬁres caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 426 Fuses Usage Fuses Usage Electrically-Controlled Air Passenger Side Low-Beam Suspension Headlamp Passenger Side High-Beam Back-Up Trailer Lamps Headlamp Driver Side High-Beam Headlamp 5-120...
Page 427 Fuses Usage Fuses Usage Driver Side Low-Beam Headlamp Engine Control Module 1 Windshield Wiper Engine Control Module Active Transfer Case Air Conditioning Windshield Washer Injector A Powertrain Control Module B Trailer Fog Lamps Antilock Brakes (ABS) Stoplamp Ignition A Cigarette Lighter Blower Ignition Coils Ignition B...
Page 428: Rear Underseat Fuse Block
Rear Underseat Fuse Block Relays Usage Headlamp Wiper Rear Window Wiper/Washer Fog Lamps Horn Fuel Pump Windshield Washer High-Beam Headlamp Air Conditioning Headlamp Driver Module Starter Electric Adjustable Pedal Powertrain Air Solenoid Miscellaneous Usage Instrument Panel Battery 5-122...
Page 429 Fuses Usage Passenger Door Control Module Driver Door Control Module Liftgate Module 2 Truck Body Controller 3 Rear Fog Lamps Blank Truck Body Controller 2 Power Seats Rear Wiper Driver Door Module Ampliﬁer Passenger Door Module Rear Climate Controls Driver Side Rear Parking Lamps Blank Vehicle Center High-Mounted Stoplamp (CHMSL)
Page 430 Fuses Usage Fuses Usage Blank Driver Side Turn Signal Unlock Heat Ventilation Air Conditioning 1 Blank Truck Body Controller 4 Blank Radio ® OnStar Overhead Battery, ® OnStar System Trailer Park Sunroof Passenger Side Turn Signal Not Used Heat Ventilation Air Conditioning Parking Lamps Rear Fog Lamps Truck Body Controller Accessory...
Page 431: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Capacities Application English Metric For the air conditioning system refrigerant charge amount, see the refrigerant caution label located Air Conditioning Refrigerant R134a under the hood.
Page 432 Capacities Application English Metric Fuel Tank 22.0 gal 83.3 L Transfer Case Lubricant 2.0 qt 1.8 L Transmission Fluid (Drain and Reﬁll) 5.0 qt 4.7 L Wheel Nut Torque 100 lb ft 140 Y All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual.
Page 433 Section 6 Maintenance Schedule Maintenance Schedule ........6-2 Owner Checks and Services ......6-8 Introduction ...........6-2 At Each Fuel Fill ..........6-9 Maintenance Requirements ......6-2 At Least Once a Month ........6-9 Your Vehicle and the Environment ....6-2 At Least Once a Year ........6-10 Using the Maintenance Schedule ......6-2 Recommended Fluids and Lubricants ....6-12 Scheduled Maintenance ........6-4...
Page 434: Maintenance Schedule
Maintenance Schedule Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep Introduction the vehicle in good working condition, but also helps the environment. All recommended maintenance is Important: Keep engine oil at the proper level and important.
Page 435 This schedule is for vehicles that: Some maintenance services can be complex. So, unless you are technically qualiﬁed and have • carry passengers and cargo within recommended the necessary equipment, have your dealer/retailer limits on the Tire and Loading Information label. do these jobs.
Page 436: Scheduled Maintenance
Scheduled Maintenance When the change engine oil light or CHANGE ENGINE OIL DIC message appears, certain services, checks, and inspections are required. Required services are When the change engine oil light or CHANGE ENGINE described in the following for “Maintenance I” and OIL DIC message displays, service is required for the “Maintenance II.”...
Page 437 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-18. Reset oil life system. • • See Engine Oil Life System on page 5-22. An Emission Control Service. • • Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter.
Page 438: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (40 000) (80 000) (120 000) (160 000)
Page 439: Maintenance Footnotes
Additional Required Services (cont’d) 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (40 000) (80 000) (120 000) (160 000) (200 000) (240 000) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). • An Emission Control Service. See footnote (i).
Page 440: Owner Checks And Services
(e) Make sure the safety belt reminder light and safety (i) Drain, ﬂush, and reﬁll cooling system. This service can belt assemblies are working properly. Look for any other be complex; you should have your dealer/retailer perform loose or damaged safety belt system parts. If you see this service.
Page 441: Engine Oil Level Check
At Each Fuel Fill At Least Once a Month It is important to perform these underhood checks at Tire Inﬂation Check each fuel ﬁll. Inspect the vehicle’s tires and make sure they are inﬂated Engine Oil Level Check to the correct pressures. Do not forget to check the spare tire, if the vehicle has one.
Page 442: At Least Once A Year
At Least Once a Year Automatic Transmission Shift Lock Control System Check Starter Switch Check CAUTION: CAUTION: When you are doing this inspection, the vehicle When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or could move suddenly.
Page 443: Ignition Transmission Lock Check
Ignition Transmission Lock Check Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking While parked, and with the parking brake set, try to turn brake. the ignition to LOCK/OFF in each shift lever position. •...
Page 444: Recommended Fluids And Lubricants
Recommended Fluids and Usage Fluid/Lubricant Lubricants ® Hydraulic Brake Delco Supreme 11 Brake Fluid or System equivalent DOT-3 brake ﬂuid. Fluids and lubricants identiﬁed below by name, part Windshield number, or speciﬁcation can be obtained from your ® Optikleen Washer Solvent. Washer dealer/retailer.
Page 445 Usage Fluid/Lubricant Usage Fluid/Lubricant SAE 75W-90 Hood Latch Rear Axle Synthetic Axle Lubricant Assembly, Lubriplate Lubricant Aerosol (Except SS (GM Part No. U.S. 89021677, Secondary (GM Part No. U.S. 12346293, Model) in Canada 89021678) meeting Latch, Pivots, in Canada 992723) or lubricant GM Speciﬁcation 9986115.
Page 446: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part GM Part Number ACDelco Part Number Automatic Transmission Filter Kit 24208576 24208576 Engine Air Cleaner/Filter 15036141 A2014C Engine Oil Filter 4.2L L6 89017342 PF61...
Page 447: Engine Drive Belt Routing
Engine Drive Belt Routing 5.3L V8 and 6.0L V8 Engines 4.2L L6 Engine 6-15...
Page 448: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 449 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 450 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 451: Customer Assistance Information
Section 7 Customer Assistance Information Customer Assistance and Information ....7-2 Reporting Safety Defects ........7-15 Customer Satisfaction Procedure ......7-2 Reporting Safety Defects to the Online Owner Center ........7-5 United States Government ......7-15 Customer Assistance for Reporting Safety Defects to the Text Telephone (TTY) Users ......7-6 Canadian Government ........7-16 Customer Assistance Offices ......7-6 Reporting Safety Defects to General Motors ..7-16...
Page 452: Customer Assistance And Information
1-800-263-3777 (English), or 1-800-263-7854 (French). Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the We encourage you to call the toll-free number in order to give your inquiry prompt attention. Have the following...
Page 453 STEP THREE — U.S. Owners: Both General Motors You may contact the BBB Auto Line Program using and your dealer are committed to making sure you are the toll-free telephone number or write them at the completely satisﬁed with your new vehicle. However, if following address: you continue to remain unsatisﬁed after following the BBB Auto Line Program...
Page 454 STEP THREE — Canadian Owners: In the event that For further information concerning eligibility in the you do not feel your concerns have been addressed Canadian Motor Vehicle Arbitration Plan (CAMVAP), after following the procedure outlined in Steps 1 and 2, call toll-free 1-800-207-0685, or call the General Motors General Motors of Canada Limited wants you to be aware Customer Communication Centre, 1-800-263-3777...
Page 455: Online Owner Center
• Online service and maintenance records • My Dealers/Retailers: Save details such as address • Find Chevrolet dealers for service nationwide and phone number for each of your preferred GM • dealers/retailers. Exclusive privileges and offers •...
Page 456: Customer Assistance For Text Telephone (Tty) Users
Chevrolet encourages customers to call the toll-free 1-800-263-7854 (French) number for assistance. However, if a customer wishes 1-800-263-3830 (For Text Telephone devices (TTYs)) to write or e-mail Chevrolet, the letter should be Roadside Assistance: 1-800-268-6800 addressed to: Overseas — Customer Assistance United States —...
Page 457: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean The offer is available for a very limited period of time from the date of vehicle purchase/lease. For more Islands/Countries (Except Puerto Rico details, or to determine your vehicle’s eligibility, visit and U.S. Virgin Islands) — Customer gmmobility.com or call the GM Mobility Assistance Center at 1-800-323-9935.
Page 458: Calling For Assistance
Roadside Assistance is not a part of the New Vehicle • Location of the vehicle Limited Warranty. Chevrolet and General Motors of • Model, year, color, and license plate number of the Canada Limited reserve the right to make any changes...
Page 459: Services Provided
Services Not Included in Roadside • Emergency Tow From a Public Road or Highway: Assistance Tow to the nearest Chevrolet dealer for warranty service, or if the vehicle was in a crash and cannot • Impound towing caused by violation of any laws.
Page 460: Scheduling Service Appointments
Services Speciﬁc to Canadian • Alternative Service: If assistance cannot be provided right away, the Roadside Assistance Purchased Vehicles advisor may give you permission to get local • emergency road service. You will receive payment, Fuel delivery: Reimbursement is approximately up to $100, after sending the original receipt to $5 Canadian.
Page 461: Courtesy Transportation
Courtesy Transportation Transportation Options Warranty service can generally be completed while you To enhance your ownership experience, we and wait. However, if you are unable to wait, GM helps to our participating dealers are proud to offer Courtesy minimize your inconvenience by providing several Transportation, a customer support program for vehicles transportation options.
Page 462: Collision Damage Repair
Courtesy Rental Vehicle Collision Damage Repair Your dealer may arrange to provide you with a courtesy If your vehicle is involved in a collision and it is damaged, rental vehicle or reimburse you for a rental vehicle that have the damage repaired by a qualiﬁed technician using you obtain if your vehicle is kept for an overnight warranty the proper equipment and quality replacement parts.
Page 463: Insuring Your Vehicle
Insuring Your Vehicle Aftermarket collision parts are also available. These are made by companies other than GM and may not have Protect your investment in your GM vehicle with been tested for your vehicle. As a result, these parts may comprehensive and collision insurance coverage.
Page 464: If A Crash Occurs
If a Crash Occurs • Gather the important information you will need from the other driver. Things like name, address, phone Here is what to do if you are involved in a crash. number, driver’s license number, vehicle license • plate, vehicle make, model and model year, Vehicle Check to make sure that you are all right.
Page 465: Reporting Safety Defects
Managing the Vehicle Damage Repair Reporting Safety Defects Process Reporting Safety Defects to the In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. United States Government If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Page 466: Reporting Safety Defects To The Canadian Government
Owner publications are written speciﬁcally for owners and intended to provide basic operational information Chevrolet Motor Division about the vehicle. The owner manual includes the Chevrolet Customer Assistance Center Maintenance Schedule for all models. P.O. Box 33170 Detroit, MI 48232-5170...
Page 467: P.o. Box
Current and Past Model Order Forms Vehicle Data Recording and Privacy Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an order form, specify year and model name of Your GM vehicle has a number of sophisticated the vehicle.
Page 468: Event Data Recorders
Event Data Recorders Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no This vehicle has an Event Data Recorder (EDR). personal data (e.g., name, gender, age, and crash The main purpose of an EDR is to record, in certain location) is recorded.
Page 469: Onstar
® OnStar Radio Frequency Identiﬁcation (RFID) If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and RFID technology is used in some vehicles for functions Conditions for information on data collection and use. such as tire pressure monitoring and ignition system ®...
Page 470 ✍ NOTES 7-20...
Page 471 Antilock Brake System (ABS) ......4-5 Antilock Brake, System Warning Light ....3-37 Accessories and Modiﬁcations ......5-3 Appearance Care Accessory Power Outlets ......... 3-19 Aluminum Wheels ........5-115 Adding a Snow Plow or Similar Equipment ..4-39 Care of Safety Belts ........5-112 Adding Equipment to Your Airbag-Equipped Chemical Paint Spotting ......
Page 472 Audio System (cont.) Bulb Replacement ........... 5-52 Setting the Clock ......... 3-63 Halogen Bulbs ..........5-52 Theft-Deterrent Feature ....... 3-109 Headlamp Aiming ........5-52 XM™ Satellite Radio Antenna System ... 3-111 License Plate Lamps ........5-54 Audio System(s) ..........3-64 Replacement Bulbs ........
Page 473 Charging System Light ........3-34 Cleaning (cont.) Check Leather ............ 5-111 Engine Lamp ..........3-39 Tires ............5-115 Gages Warning Light ........3-45 Underbody Maintenance ......5-116 Check Gas Cap Light ........3-47 Washing Your Vehicle ......... 5-113 Checking Things Under the Hood ...... 5-10 Weatherstrips ..........
Page 474 Customer Assistance Information Door Courtesy Transportation ........ 7-11 Delayed Locking ........... 2-8 Customer Assistance for Locks ............2-7 Text Telephone (TTY) Users ......7-6 Power Door Locks ......... 2-8 Customer Assistance Offices ......7-6 Programmable Automatic Door Locks ....2-9 Customer Satisfaction Procedure .....
Page 475 Engine (cont.) Overheating ..........5-35 EDR ............. 7-17 Reduced Power Light ........3-44 Electrical System Starting ............2-23 Add-On Equipment ........5-118 Entry Lighting ..........3-17 Engine Compartment Fuse Block ....5-119 Event Data Recorders ........7-18 Fuses and Circuit Breakers ......5-119 Exit Lighting ...........
Page 476 Fuel ............... 5-5 Gasoline Additives ............5-7 Octane ............5-6 California Fuel ..........5-6 Speciﬁcations ..........5-6 Check Gas Cap Light ........3-47 Gate Ajar Light ..........3-46 Driving for Better Economy ......4-2 Glove Box ............. 2-53 Filling a Portable Fuel Container ....5-10 GM Mobility Reimbursement Program ....
Page 477 Hood Checking Things Under ........ 5-10 Labeling, Tire Sidewall ........5-60 Release ............. 5-11 Lamp Horn ............... 3-6 Malfunction Indicator ........3-39 How to Wear Safety Belts Properly ....1-18 Lamps Dome ............3-17 Dome Lamp Override ........3-17 Reading ............. 3-17 Ignition Positions ..........
Page 478 Light (cont.) Luggage Carrier ..........2-54 Passenger Airbag Status Indicator ....3-33 Lumbar Reduced Engine Power ........ 3-44 Manual Controls ..........1-3 Safety Belt Reminders ........3-31 Power Controls ..........1-4 Security ............. 3-44 Service Four-Wheel-Drive Warning Light ..3-45 StabiliTrak Service ........
Page 479 Mirrors Online Owner Center ........7-5 Automatic Dimming Rearview ......2-40 OnStar, Privacy ..........7-19 ® ® Manual Rearview Mirror ........ 2-40 OnStar System, see OnStar Manual ....2-45 Outside Convex Mirror ......... 2-44 Operation, Universal Home Remote System ..2-49 Outside Heated Mirrors ........
Page 480 ® PASS-Key III+ Electronic Immobilizer Operation ........... 2-19 ® Radiator Pressure Cap ........5-34 Passlock ............2-18 Radio Frequency Identiﬁcation (RFID), Privacy ..7-19 Perchlorate Materials Requirements, California ..5-4 Radio(s) ............3-64 Phone ® Radios Bluetooth ..........3-85 Navigation/Radio System, see Navigation Power Manual ...........
Page 481 Rear Windshield Washer/Wiper ......3-10 Rearview Mirror, Automatic Dimming ....2-40 Safety Belt Reminders ........3-31 Rearview Mirrors ..........2-40 Safety Belts Reclining Seatbacks .......... 1-7 Care of ............ 5-112 Recommended Fluids and Lubricants ....6-12 How to Wear Safety Belts Properly ....1-18 Recovery Hooks ..........
Page 482 Service ............5-3 Steering Wheel Controls, Audio ....... 3-109 Accessories and Modiﬁcations ......5-3 Steering Wheel, Tilt Wheel ......... 3-6 Adding Equipment to the Outside of the Storage Areas Vehicle ............. 5-5 Center Console Storage Area ......2-54 California Perchlorate Materials Requirements ..5-4 Convenience Net .........
Page 483 Tire Tires (cont.) Pressure Light ..........3-39 Tire Terminology and Deﬁnitions ....5-62 Tire Sealant Uniform Tire Quality Grading ......5-78 Storing ............5-92 Wheel Alignment and Tire Balance ....5-80 Tires ............. 5-58 Wheel Replacement ........5-80 Aluminum Wheels, Cleaning ......5-115 When It Is Time for New Tires ......
Page 484 Where to Put the Restraint ....... 1-42 Windows ............2-14 Vehicle Power ............2-15 Control ............4-3 Windshield Loading ............4-33 Backglass, and Wiper Blades, Cleaning ..5-114 Running While Parked ........2-39 Washer ............3-9 Symbols ............iv Washer Fluid ..........5-38 Vehicle Customization, DIC ......

Chevrolet 2009 TrailBlazer Owner's Manual

Section 1 Seats and Restraint System

Seats and Restraint System

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Quick Links

Chapters

Related Manuals for Chevrolet 2009 TrailBlazer

Summary of Contents for Chevrolet 2009 TrailBlazer