Page 1 2009 Chevrolet Aveo Owner Manual Seats and Restraint System ... 1-1 Head Restraints ... 1-2 Front Seats ... 1-4 Rear Seats ... 1-9 Safety Belts ... 1-16 Child Restraints ... 1-34 Airbag System ... 1-60 Restraint System Check ... 1-75 Features and Controls ...
Page 2: Canadian Owners
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3: Vehicle Symbols
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Page 4: Vehicle Symbol Chart
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. : Airbag Readiness Light : Air Conditioning : Antilock Brake System (ABS) : Audio Steering Wheel Controls or OnStar : Brake System Warning Light "...
Page 5: Table Of Contents
Section 1 Head Restraints ...1-2 Front Seats ...1-4 Manual Seats ...1-4 Seat Height Adjuster ...1-5 Manual Lumbar ...1-5 Reclining Seatbacks ...1-6 Rear Seats ...1-9 Rear Seat Operation (Sedan) ...1-9 Rear Seat Operation (Hatchback) ...1-12 Safety Belts ...1-16 Safety Belts: They Are for Everyone ...1-16 How to Wear Safety Belts Properly ...1-21 Lap-Shoulder Belt ...1-30 Safety Belt Use During Pregnancy ...1-33...
Page 6: Head Restraints
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. CAUTION: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Page 7 Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place. The head restraints are not designed to be removed.
Page 8: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 9: Manual Lumbar
Seat Height Adjuster Turn the knob located on the outboard side of the seat cushion to adjust the height of the driver seat cushion. Turn the knob forward to raise the height of the seat cushion and rearward to lower it. Manual Lumbar On vehicles with front seat manual lumbar, the...
Page 10: Reclining Seatbacks
Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 11 To recline the seatback: 1. Lift the recline lever. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked. To return the seatback to an upright position: 1.
Page 12 CAUTION: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even if when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 13: Rear Seats
Rear Seats Rear Seat Operation (Sedan) Folding the Seatbacks The rear seatbacks can be folded down to increase cargo space. To fold down the seatbacks: Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
Page 14 4. Detach the center safety belt from the mini buckle by inserting the ignition key into the slot in the mini buckle, pressing the release button, and allowing the belt to retract. 1-10 5. Pull up the release knob located on top of either of the rear seatbacks.
Page 15 CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push down and rearward ﬁrmly on the top of the seatbacks until it latches securely in the fully upright position.
Page 16: Rear Seat Operation (Hatchback)
Rear Seat Operation (Hatchback) Folding the Rear Seats The rear seats can be folded to increase cargo space. To fold the rear seats: 1. Lower the head restraints completely. 2. Unlatch the center safety belt by pressing the red button on the buckle. 1-12 3.
Page 17 4. Pull up the release knob, located on the top of the seatbacks, and fold the seatbacks forward and down. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.
Page 18: Unfolding The Seats
8. Clip the hook to the front seat head restraint to keep the rear seat secure. Unfolding the Seats To return the rear seats to the normal seating position: 1. Unclip the hook from the front seat head restraint. 2. Position the buckles in back of the seat latches when moving the rear seats to the sitting position.
Page 19 CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 20: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 21: Why Safety Belts Work
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 22 Put someone on it. 1-18 Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 23 The person keeps going until stopped by something. or the instrument panel... In a real vehicle, it could be the windshield... 1-19...
Page 24: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-20 Questions and Answers About Safety Belts...
Page 25: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt.
Page 26 Sit up straight and always keep your feet on the ﬂoor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. 1-22 In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Page 27 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 28 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 1-24 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 29 What is wrong with this? The belt is buckled in the wrong buckle. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 30 What is wrong with this? The belt is over an armrest. 1-26 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 31 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 32 What is wrong with this? The belt is behind the body. 1-28 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 33 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 34: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Rear Seat Operation (Sedan) on page 1-9 or Rear Seat Operation (Hatchback) on page 1-12 for instruction on reconnecting the safety belt to the mini-buckle.
Page 35 4. Push the latch plate into the buckle until it clicks. If the latch plate will not go fully into the buckle, check if the correct buckle is being used. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-34.
Page 36: Shoulder Belt Height Adjuster
To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the belt is out of the way. If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle.
Page 37: Safety Belt Pretensioners
Safety Belt Pretensioners This vehicle has safety belt pretensioners for front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal or near frontal crash if the threshold conditions for pretensioner activation are met.
Page 38: Safety Belt Extender
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 39 The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
Page 40 CAUTION: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. 1-36...
Page 41 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 42: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 43 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint CAUTION: (Continued) CAUTION: (Continued) in a rear seat.
Page 44 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 45: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 46 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-42 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the...
Page 47: Securing The Child Within The Child Restraint
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 48: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;...
Page 49 When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. There are a couple of things you need to know about using child restraints in your rear seat: If you use a child restraint in the center rear seating position (A), the safety...
Page 50: Lower Anchors And Tethers For Children (Latch)
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Page 51: Top Tether Anchor
Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 52 To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. Hatchback models may have zippers over the lower anchor areas. If so, unzip the seat cover below the labels to access each lower anchor.
Page 53 Hatchback For hatchback models, the top tether anchors (B) are located in the rear cargo area, attached to the back wall (A) of the vehicle. Squeeze and pull the front part of the plastic cover to access the top tether anchors. Remove the cargo shade before installing the top tether.
Page 54: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with the child...
Page 55 Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
Page 56 2.5. Route and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback.
Page 57: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-46 for how to install your child restraint using LATCH.
Page 58 3. Push the latch plate into the buckle until it clicks. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. If you ﬁnd that the latch plate will not go fully into the buckle, see if you are using the correct buckle.
Page 59 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 60: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-44. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions.
Page 61 CAUTION: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
Page 62 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. Tilt the latch plate to adjust the belt if needed. 1-58 4.
Page 63 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 64: Airbag System
If a child restraint has been installed and the off symbol is not lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 1-67 for more information. To remove the child restraint, unbuckle the vehicle’s safety belt and let it go back all the way.
Page 65 CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Page 66: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. 1-62 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side.
Page 67 Driver Side shown, Passenger Side similar If your vehicle has seat-mounted side impact airbags for the driver and right front passenger, they are in the side of the seatbacks closest to the door. CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 68: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 69: What Makes An Airbag Inﬂate
In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inﬂation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down.
Page 70: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize the airbags inﬂated. Some components of the airbag module may be hot for several minutes.
Page 71: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 72 According to accident statistics, children are safer when properly secured in a rear seat in the correct child restrain for their weight and size. We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;...
Page 73 • The system determines that a small child is present in a booster seat. • A right front passenger takes his/her weight off of the seat for a period of time. • The right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints.
Page 74 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 75 If the On Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off symbol is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side...
Page 76 Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 77: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-17.
Page 78: Adding Equipment To Your Airbag-Equipped Vehicle
Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 79: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 80: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 81: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry (RKE) System ...2-3 Remote Keyless Entry (RKE) System Operation ...2-4 Doors and Locks ...2-6 Door Locks ...2-6 Central Door Unlocking System ...2-7 Door Ajar Reminder ...2-7 Rear Door Security Locks ...2-7 Trunk (Sedan) ...2-8 Liftgate (Hatchback) ...2-10 Windows ...2-12 Manual Windows ...2-12...
Page 82: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 83: Remote Keyless Entry (Rke) System
page 2-15 for additional information. If a replacement key or an additional key is needed, it must be purchased from your dealer/retailer or certiﬁed locksmith. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys.
Page 84: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 65 feet (20 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3. Hatchback The following functions may be available if the vehicle has RKE:...
Page 85: Battery Replacement
Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed.
Page 86: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 87: Central Door Unlocking System
Central Door Unlocking System Your vehicle may be equipped with the central door unlocking system. This system is activated from the driver’s door. From the outside, you can lock or unlock all the doors by using either the key or the remote keyless entry transmitter, if equipped.
Page 88: Trunk (Sedan)
Opening a Rear Door When the Security Lock is On 1. Unlock the door from the inside. 2. Open the door from the outside. If you do not cancel the security lock, adults or older children who ride in the rear will not be able to open the rear door from the inside.
Page 89: Remote Trunk Release
To open the trunk on your sedan from outside of your vehicle, insert the key into the lock cylinder and turn the key clockwise or use the remote keyless entry transmitter, if equipped. Remote Trunk Release If your vehicle has a trunk release button located on the driver’s door, you can open the trunk from...
Page 90: Emergency Trunk Release Handle
Emergency Trunk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside.
Page 91 CAUTION: (Continued) • Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. • If the vehicle is equipped with a power liftgate, disable the power liftgate function.
Page 92: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 93: Power Windows
Power Windows CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Page 94: Sun Visors
Window Lockout The window lockout is located with the driver’s power window switches. Press the lockout button to stop the rear passengers from using their window switches. The driver can still operate all the windows with the lockout on. Press the lockout button again to return to normal window operation.
Page 95: Immobilizer Operation
Immobilizer Operation The vehicle may have a passive theft-deterrent system. The immobilizer system prevents the vehicle from being started by an unauthorized person by isolating the power supply to the ignition system, the fuel pump and the fuel injectors. The system is automatically armed when the key is removed from the ignition.
Page 96: Arming The System
Content Theft-Deterrent Your vehicle may have a content theft-deterrent system. The theft-deterrent system will not arm when you lock the doors using the key or the manual door lock. It arms only when you use the remote keyless entry transmitter. Arming the System To arm the system, do the following: 1.
Page 97: Disarming The System
Disarming the System To disarm the system, do one of the following: • Unlock the driver’s or passenger’s front door using the key. • Press the unlock button on the remote keyless entry transmitter. − The LED light on the transmitter will ﬂash once.
Page 98: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km).
Page 99: Starting The Engine
Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer.
Page 100: Starting Procedure
Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to START. When the engine starts, let go of the key. The idle speed will go down as the engine gets warm. Notice: Holding the key in START for longer than 15 seconds at a time will cause the battery to be drained much sooner.
Page 101: Engine Heater
Engine Heater The engine heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F (−18°C). Vehicles with an engine heater should be plugged in at least four hours before starting. To Use the Engine Heater 1.
Page 102: Automatic Transmission Operation
Automatic Transmission Operation If the vehicle has an automatic transmission, the shift lever is located on the console between the seats. Movement between certain positions requires pushing the release button on the front of the shifter. P (Park): This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily.
Page 103 R (Reverse): Use this gear to back up. When shifting from N (Neutral) to R (Reverse), you need to apply the brake pedal and push the release button on the front of the shifter. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission.
Page 104 D4 (Automatic Overdrive): This position is for normal driving. When operating the vehicle in severe cold conditions, the transmission may be prevented from shifting into D4 gear until the transmission ﬂuid has warmed up to it’s operational temperature. Notice: If the vehicle seems to start up rather slowly or not shift gears when you go faster, and you continue to drive the vehicle that way, you could damage the transmission.
Page 105: Hold Mode
Hold Mode If the vehicle’s transmission has hold mode, you can select this mode to allow the automatic transmission to stay in a speciﬁc gear range. Press the HOLD button on the shift lever console to turn on hold mode. Press the button again to turn off hold mode, and return to normal automatic transmission operation.
Page 106: Manual Transmission Operation
Manual Transmission Operation Five-Speed This is your shift pattern. 1 (First): Press the clutch pedal and shift into 1 (First). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 2-26 You can shift into 1 (First) when you are going less than 20 mph (32 km/h).
Page 107: Shift Speeds
R (Reverse): To back up, press down the clutch pedal, lift up the ring on the shift lever and shift into R (Reverse). Let up on the clutch pedal slowly while pressing the accelerator pedal. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission.
Page 108: Parking Brake
Parking Brake The parking brake lever is located between the bucket seats. 2-28 To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-28.
Page 109: Shifting Into Park (Automatic Transmission)
Shifting Into Park (Automatic Transmission) CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 110: Shifting Out Of Park
Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift your transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park).
Page 111: Parking The Vehicle (Manual Transmission)
4. Insert the key into the shift lock slot and press and hold the key. 5. Shift to N (Neutral). 6. Remove the key from the slot, insert the key into the ignition and start the engine. 7. Replace the shift-lock release slot cover. 8.
Page 112: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 113: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 114: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Page 115: Outside Power Mirrors
Outside Power Mirrors The control is located on the instrument panel, left of the steering wheel. The ignition must be turned to ON/RUN to adjust the mirrors. To adjust the mirrors: 1. Select the mirror you want to adjust by moving the selector switch to L for the driver side mirror or R for the passenger side mirror.
Page 116: Onstar System
® OnStar System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
Page 117 OnStar Services Available with the Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert •...
Page 118: Onstar Virtual Advisor
OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information.
Page 119: Storage Areas
Storage Areas The vehicle has shopping hooks on each front seatback. Lift the headrest to access the hooks. Glove Box Lift up on the glove box lever to open it. Cupholders Two cupholders are located in the center instrument panel, below the climate control system. To use the cupholder, push in on the cover, then pull it out.
Page 120: Sunglasses Storage Compartment
Sunglasses Storage Compartment For vehicles with this feature, the sunglasses storage compartment is located above the driver’s door. To open, pull down and hold the upper part of the cover. Release the cover and the compartment will automatically close. 2-40 Sunroof On vehicles with this feature, the switch is...
Page 121 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-8 Windshield Washer ...3-9 Rear Window Wiper/Washer ...3-10 Cruise Control ...3-10 Exterior Lamps ...3-13 Daytime Running Lamps (DRL) ...3-14...
Page 122 Section 3 Change Engine Oil Light ...3-35 Fog Lamp Light ...3-35 Cruise Control Light ...3-36 Highbeam On Light ...3-36 Daytime Running Lamps (DRL) Indicator Light ...3-36 Door Ajar Light ...3-36 Fuel Gage ...3-37 Low Fuel Warning Light ...3-38 Trip Computer ...3-38 Instrument Panel Audio System(s) ...3-40 AM-FM Radio ...3-41...
Page 123 ✍ NOTES...
Page 124: Instrument Panel Overview
Instrument Panel Overview...
Page 125 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-21. B. Instrument Panel Cluster on page 3-24. C. Clock on page 3-17. D. Hood Release on page 5-12. E. Horn on page 3-6. F. Audio System(s) on page 3-40. G.
Page 126: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂasher button is located to the right of the climate control system on the sedan. Hazard Warning Flasher: Press to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble.
Page 127: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane-Change Signals : Headlamp High/Low-Beam Changer : Exterior Light Control : Fog Lamps, if equipped Flash-to-Pass Feature. Information for these features is on the pages following. Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change.
Page 128: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer Windshield Wipers The headlamps must be on for this feature to work. Push the turn signal lever away from you to turn the high beams on. This instrument panel cluster light comes on while the high beams are on and the ignition is turned to ON/RUN.
Page 129: Windshield Washer
The lever is located on the right side of the steering column. The ignition must be turned to ON/RUN to operate the windshield wipers. Move the lever to one of the following positions: HI (High Speed): For steady wiping at high speed. LO (Low Speed): For steady wiping at low speed.
Page 130: Rear Window Wiper/Washer
Rear Window Wiper/Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The vehicle may have a rear window wiper/washer. Turn the rear wiper/washer band to operate the rear window wiper/washer.
Page 131: Setting Cruise Control
The cruise control buttons are located on the right side of the steering wheel. (On/Off): Press to turn the cruise control on or off. RES+ (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed. SET– (Set/Coast): Press to set the speed or make the vehicle decelerate.
Page 132 Resuming a Set Speed If the cruise control is set to a desired speed and then the brakes are applied, or the clutch pedal if you have a manual transmission, the cruise control shuts off. But it does not need to be reset. Once the vehicle is going about 24 mph (39 km/h) or more, brieﬂy press the RES+ button.
Page 133: Exterior Lamps
Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed.
Page 134: Daytime Running Lamps (Drl)
(Parking Lamps): Turns on the parking lamps, together with the taillamps, license plate lamp, and instrument panel lights. OFF: Turns all the lamps off, except the Daytime Running Lamps (DRL). Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day.
Page 135: Fog Lamps
Fog Lamps For vehicles with fog lamps, they are controlled by band located on the middle of the turn signal/ multifunction lever. To use the fog lamps, the ignition must be turned to ON/RUN and the low-beam headlamps or parking lamps must be on.
Page 136: Dome Lamp
Dome Lamp The vehicle has a dome lamp. ON: The light comes on and stays on. (Door): The light comes on when a door is opened. The light turns off when all the doors are closed. OFF: The light remains off even when a door is opened. Inadvertent Power Battery Saver This feature is designed to protect the vehicle’s battery against drainage.
Page 137: Ashtray(S) And Cigarette Lighter
Notice: Improper use of the power outlet can cause damage not covered by the warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Ashtray(s) and Cigarette Lighter The ashtray is located at the lower part of the center instrument panel.
Page 138: Climate Controls
Climate Controls Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. Climate Control System with Heater and Air Conditioning A. Temperature Control D. Air Conditioning (A/C) B. Fan Control E. Recirculation C. Air Delivery Mode F.
Page 139 OFF: Turns the fan off. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature of the air ﬂowing from the system. (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. The fan must be turned on to run the air conditioning compressor.
Page 140 For quick cool down on hot days, do the following: 1. Open the windows to let hot air escape. 2. Press 3. Press A/C. 4. Select the coolest temperature. 5. Select the highest speed. Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry.
Page 141: Outlet Adjustment
Rear Window and Outside Mirror Defogger For vehicles with a rear window and outside mirror defogger, they only work when the ignition is turned to ON/RUN. The rear window defogger uses a warming grid to remove fog or frost from the rear window. <...
Page 142: Passenger Compartment Air Filter
Passenger Compartment Air Filter For vehicles with a passenger compartment air ﬁlter, it is located behind the glove box. It can be accessed after removing the glove box from its housing. Pollen and dust are removed by the ﬁlter. The air cleaner/ﬁlter may need to be changed periodically.
Page 143: Warning Lights, Gages, And Indicators
4. Replace the air conditioner ﬁlter. 5. View the air ﬂow arrows on the ﬁlter before installing to ensure the ﬁlter is installed correctly. Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 144: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It indicates how fast the vehicle is going, how much fuel is being used, and many other things needed to drive safely and economically. The vehicle’s instrument panel cluster includes indicator warning lights and gages that are explained on the following pages.
Page 145: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Trip Odometer The trip odometer can record the number of miles, used in the United States, or kilometers, used in Canada,...
Page 146: Safety Belt Reminders
Safety Belt Reminders Safety Belt Reminder Light When the engine is started this light and chime comes on and stays on for several seconds to remind the people to fasten their safety belts. The light also begins to ﬂash. This cycle repeats if the driver remains unbuckled and the vehicle is moving.
Page 147: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-67 for important safety information. The vehicle has a passenger airbag status indicator near the clock, located in the center of the instrument panel. United States When the vehicle is started, the passenger airbag status indicator will light ON and OFF or the symbol for on and...
Page 148: Charging System Light
Charging System Light This light will come on brieﬂy when the ignition is turned on, and the engine is not running, as a check to show it is working. It should go out when the engine is started. If it stays on, or comes on while driving, there may have a problem with the electrical charging system.
Page 149 United States CAUTION: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
Page 150: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. If the light stays on, turn the ignition to LOCK/OFF or if the light comes on, stop as soon as possible and turn the ignition off.
Page 151: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States The vehicle has an engine coolant temperature gage. With the ignition turned to ON/RUN, this gage shows the engine coolant temperature. If the gage pointer moves into the red area, the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible.
Page 152: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light comes on when the ignition is on, but the engine is not running, as a...
Page 153 The following can prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine.
Page 154: Oil Pressure Light
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: •...
Page 155: Maintenance Schedule
CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Page 156: Cruise Control Light
Cruise Control Light If the vehicle has cruise control, this light comes on whenever the cruise control is set. The light will go out when the cruise control is turned off. See Cruise Control on page 3-10 for more information. Highbeam On Light This light comes on when the high-beam headlamps...
Page 157: Fuel Gage
Fuel Gage United States The fuel gage indicates about how much fuel is left when the ignition is turned to ON/RUN. When the tank nears empty, the low fuel warning light will come on. There is still a little fuel left, but the vehicle’s fuel tank should be ﬁlled soon.
Page 158: Low Fuel Warning Light
Low Fuel Warning Light This light comes on when the vehicle is low on fuel. The low fuel warning light comes on when there is approximately 1.7 gallons (6.0 liters) of fuel remaining in the tank. To turn the light off, add fuel to the fuel tank. See Filling the Tank on page 5-8.
Page 159: Outside Temperature
The fuel range estimate is based on an average of the vehicle’s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the...
Page 160: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 161: Am-Fm Radio
AM-FM Radio Playing the Radio (Power/Volume): Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. Turn to increase or decrease the volume. When the system is on, press and release the system.
Page 162: Storing A Radio Station
If the Automatic Store function is started in the AM band, only AM stations are stored in A1 and A2. A combination of AM, FM and XM (if equipped) stations can be stored manually into the other four favorite pages. To use Automatic Store: 1.
Page 163 To setup the number of favorites pages: 1. Press and hold FAV until the radio setup menu displays. 2. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 3. Press FAV to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages.
Page 164 Adjusting the Speakers (Balance/Fade) SOUND (Balance/Fade): Press to adjust the balance or fade. Adjusting the Balance To adjust the balance: 1. Press SOUND. 2. Press the pushbutton below the Bal tab on the display. 3. Turn to adjust the setting. 4.
Page 165: Xm Satellite Radio Service
XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle.
Page 166: Radio With Cd
Radio with CD Playing the Radio (Power/Volume): Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. Turn to increase or decrease the volume. When the system is on, press and release the system.
Page 167 If the Automatic Store function is started in the FM band, only FM stations are stored in preset pages A1 and A2. If the Automatic Store function is started in the AM band, only AM stations are stored in A1 and A2. A combination of AM, FM and XM (if equipped) stations can be stored manually into the other four favorite pages.
Page 168 To setup the number of favorites pages: 1. Press and hold FAV until the radio setup menu displays. 2. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 3. Press FAV to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages.
Page 169 Adjusting the Speakers (Balance/Fade) SOUND (Balance/Fade): Press to adjust the balance or fade. Adjusting the Balance To adjust the balance: 1. Press SOUND. 2. Press the pushbutton below the Bal tab on the display. 3. Turn to adjust the setting. 4.
Page 170: Playing A Cd
XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle.
Page 171 BAND: Press to listen to the radio while a CD is playing. The CD remains inside the radio for future listening. CD/AUX: Press to play a CD when listening to the radio. CDP appears on the display when the CD player has been selected.
Page 172: Care Of Cds
CD Messages CHECK CD: If this message displays and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • The road is very rough. When the road becomes smoother, the CD should play.
Page 173 Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign...
Page 174: Using An Mp3
Using an MP3 MP3/WMA CD-R Disc MP3 Format If you burn your own MP3/WMA disc on a personal computer: • Make sure the MP3/WMA ﬁles are recorded on a CD-R disc. • Do not mix standard audio and MP3/WMA ﬁles on one disc.
Page 175: Playing An Mp3/Wma
No Folder When a CD contains only compressed ﬁles, the ﬁles are located under the root folder. The next and previous folder function does not function on a CD that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT. When a CD contains only compressed audio ﬁles, but no folders, all ﬁles are located under the root folder.
Page 176: Xm Radio Messages
SEEK (Next/Previous Folder) (in MP3/WMA Mode): Press to change the folder. If CD-R does not have any folders, “ROOT” ﬂashes on the display for a short time. TUNE (Next Track): Press the up TUNE arrow to go to the next track. The track number displays. The player continues moving forward through the CD each time TUNE is pressed.
Page 177: Audio Steering Wheel Controls
Audio Steering Wheel Controls Front View of the Steering Wheel Controls If the vehicle has this feature, some audio controls can be adjusted at the steering wheel. PWR (Power): Press and release to turn the system on and off. When the system is on, press and release for a short time to mute the system.
Page 178: Radio Reception
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 179: Backglass Antenna (Sedan)
Check occasionally to make sure the mast is still tightened to the antenna base located on the roof of the vehicle. If tightening is required, tighten by hand. Backglass Antenna (Sedan) ® Vehicles without OnStar have the AM-FM antenna integrated with the rear window defogger, located in the rear window.
Page 180 ✍ NOTES 3-60...
Page 181: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-6 Steering ...4-6 Off-Road Recovery ...4-8 Passing ...4-8 Loss of Control ...4-8...
Page 182: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 183: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 184: Braking
Braking See Brake System Warning Light on page 3-28. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second. But that is only an average.
Page 185: Antilock Brake System (Abs)
Antilock Brake System (ABS) The vehicle might have the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. If the vehicle has ABS, this warning light comes on brieﬂy when the vehicle is started. The warning light is on the instrument panel cluster.
Page 186: Power Steering
Braking in Emergencies At some time, nearly every driver gets into a situation that requires hard braking. If the vehicle has ABS, it allows the driver to steer and brake at the same time. However, if the vehicle does not have ABS, the ﬁrst reaction — to hit the brake pedal hard and hold it down —...
Page 187: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 188: Off-Road Recovery
Off-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 189 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Page 190: Driving At Night
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. •...
Page 191: Before Leaving On A Long Trip
Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. There is no hard and fast rule about hydroplaning.
Page 192: Highway Hypnosis
Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, ﬁnd a safe place to park your vehicle and rest. Other driving tips include: • Keep the vehicle well ventilated. • Keep interior temperature cool.
Page 193: Winter Driving
• Stay in your own lane. Do not swing wide or cut across the center of the road. Drive at speeds that let you stay in your own lane. • Top of hills: Be alert — something could be in your lane (stalled car, accident).
Page 194 Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-7. To get help and keep everyone in the vehicle safe: •...
Page 195: If Your Vehicle Is Stuck In Sand, Mud, Ice
Run the engine for short periods only as needed to keep warm, but be careful. To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
Page 196: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Shift back and forth between R (Reverse) and a forward gear, or with a manual transmission, between 1 (First) or 2 (Second) and R (Reverse), spinning the wheels as little as possible.
Page 197 Tire and Loading Information Label - United States Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The Tire and Loading Information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms...
Page 198 The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be ﬁve 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 - 750 (5 x 150) = 650 lbs).
Page 199 Example 2 Item Description Vehicle Capacity Weight for Example 2 = Subtract Occupant Weight 150 lbs (68 kg) × 5 = Available Cargo Weight = Total Item 1,000 lbs Vehicle Capacity Weight for Example 3 = (453 kg) Subtract Occupant 750 lbs Weight 200 lbs (340 kg)
Page 200 Tire and Loading Information Label - Canada Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the driver’s side, center pillar (B-pillar). This label shows the Maximum Load amount, the number of occupant seating 4-20 positions, the original equipment tires, and the recommended cold tire inﬂation pressure.
Page 201 Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, the load from your trailer will be transferred to your vehicle.
Page 202 Example 2 Item Description Vehicle Capacity Weight or Maximum Load for Example 2 = Subtract Occupant Weight 150 lbs (68 kg) × 5 = Available Cargo Weight = 4-22 Total Item Vehicle Capacity Weight 1,000 lbs or Maximum Load (453 kg) for Example 3 = Subtract Occupant 750 lbs...
Page 203 Certiﬁcation Label Label Example - United States Label Example - Canada A vehicle speciﬁc Certiﬁcation label is attached to the center pillar (B-pillar), below the driver’s door latch. This label tells you the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR).
Page 204: Towing
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going.
Page 205: Dinghy Towing
Here are some important things to consider before recreational vehicle towing: • What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer’s recommendations. • What is the distance that will be travelled? Some vehicles have restrictions on how far and how long they can tow.
Page 206 Dolly Towing From the Front The vehicle can be towed from the front using a dolly. To tow the vehicle using a dolly, follow these steps: 1. Attach the dolly to the tow vehicle following the dolly manufacturer’s instructions. 2. Drive the front wheels onto the dolly. 4-26 3.
Page 207: Towing A Trailer
Dolly Towing From the Rear Notice: Towing the vehicle from the rear with the front wheels on the ground could cause transmission damage. Do not tow the vehicle from the rear with the front wheels on the ground. Towing a Trailer The vehicle is neither designed nor intended to tow a trailer.
Page 208 ✍ NOTES 4-28...
Page 209: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7...
Page 210 Section 5 Tire Pressure Monitor Operation ...5-60 Tire Inspection and Rotation ...5-62 When It Is Time for New Tires ...5-63 Buying New Tires ...5-64 Different Size Tires and Wheels ...5-65 Uniform Tire Quality Grading ...5-66 Wheel Alignment and Tire Balance ...5-67 Wheel Replacement ...5-67 Tire Chains ...5-68 If a Tire Goes Flat ...5-69...
Page 211: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like...
Page 212: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 213: Adding Equipment To The Outside Of
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-73. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-17.
Page 214: California Fuel
California Fuel If the vehicle is certiﬁed to meet California Emissions Standards, it is designed to operate on fuels that meet California speciﬁcations. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance might be affected.
Page 215: Fuels In Foreign Countries
Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the speciﬁcations described earlier.
Page 216: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling.
Page 217 Hatchback shown. Sedan similar The tethered fuel cap is located behind a hinged fuel door on the passenger side of the vehicle. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right.
Page 218 When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-32.
Page 219: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 220: Hood Release
Hood Release To open the hood: 1. Pull the hood release handle inside the vehicle. It is located on the lower left side of the instrument panel. 5-12 2. Then go to the front of the vehicle and lift up on the secondary hood release lever, located under the front center of the hood.
Page 221 Before closing the hood, be sure all the ﬁller caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the inner fender and return the prop to its retainer. Lower the hood 12 inches (30 cm) above the vehicle and release it so it fully latches.
Page 222: Engine Compartment Overview
Engine Compartment Overview Automatic Transmission shown, Manual Transmission similar 5-14...
Page 223 A. Engine Air Cleaner/Filter on page 5-19. B. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-16. C. Brake/Clutch Fluid Reservoir. See “Brake Fluid” under Brakes on page 5-34 and Hydraulic Clutch on page 5-23.
Page 224: Engine Oil
Engine Oil If the engine oil pressure light comes on, check the engine oil level right away. The oil pressure light is on the instrument panel cluster. See Oil Pressure Light on page 3-34. Check the engine oil level regularly; this is an added reminder. Checking Engine Oil It is a good idea to check the engine oil level at each fuel ﬁll.
Page 225: Cold Temperature Operation
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Page 226: Engine Oil Life System
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system ﬂushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 227: Engine Air Cleaner/Filter
If the change engine oil light comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the reset procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer.
Page 228 To inspect or replace the air cleaner/ﬁlter: 1. Remove the screws and lift off the cover. 2. Inspect or replace the engine air cleaner/ﬁlter. 3. Put the cover back on tightly and tighten the screws. See Additional Required Services on page 6-6 for replacement intervals.
Page 229: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check Automatic Transmission Fluid Check the automatic transmission ﬂuid level at least twice a year. Add ﬂuid if needed. See Scheduled Maintenance on page 6-4. How to Check Automatic Transmission Fluid Because this operation can be a little difficult, you may choose to have this done at the dealer/retailer service department.
Page 230: How To Add Automatic Transmission Fluid
Then, without shutting off the engine, follow these steps: 1. Locate the automatic transmission dipstick which is located toward the front of the engine compartment, near the power steering ﬂuid reservoir. See Engine Compartment Overview on page 5-14 for more information on location. 2.
Page 231: Manual Transmission Fluid
Manual Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to the dealer/retailer service department and have it repaired as soon as possible.
Page 232: Cooling System
Cooling System The cooling system allows the engine to maintain the correct working temperature. A. Electric Engine Cooling Fan B. Coolant Surge Tank with Pressure Cap 5-24 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury.
Page 233: Engine Coolant
CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 234: What To Use
What to Use CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning.
Page 235 The engine coolant surge tank is located in the rear of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 5-14 for more information on location. CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 236: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant Surge Tank CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a speciﬁc coolant ﬁll procedure.
Page 237 2. Then keep turning the pressure cap slowly and remove it. 3. Fill the coolant surge tank with the proper mixture to the Maximum mark on the coolant surge tank. Wait about ﬁve minutes, then check to see if the level is below the mark. If the level is below the Maximum mark, add additional coolant to bring the level up to the mark.
Page 238: Engine Overheating
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower.
Page 239: If Steam Is Coming From The Engine Compartment
If Steam Is Coming From The Engine Compartment CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 240: Power Steering Fluid
If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Power Steering Fluid When to Check Power Steering Fluid The power steering ﬂuid reservoir is located toward the...
Page 241: Windshield Washer Fluid
What to Use To determine what kind of ﬂuid to use, see Recommended Fluids and Lubricants on page 6-13. Always use the proper ﬂuid. Failure to use the proper ﬂuid can cause leaks and damage hoses and seals. Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use.
Page 242: Brakes
Brakes Brake Fluid The vehicle has one reservoir for both the brake and clutch hydraulic systems. It is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-14 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down: •...
Page 243 What to Add Use only new DOT-3 brake ﬂuid from a sealed container. See Recommended Fluids and Lubricants on page 6-13. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Page 244: Brake Adjustment
Brake Wear This vehicle has front disc brakes and could have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 245: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced —...
Page 246: Jump Starting
Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 247 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3.
Page 248 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 249 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery.
Page 250 9. Connect the other end of the negative (−) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less.
Page 251: Headlamp Aiming
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 252: Headlamps
Headlamps To replace a headlamp bulb: 1. Open the hood. See Hood Release on page 5-12. 2. Remove the three bolts to remove the headlamp assembly. 3. Disconnect the wiring harness connector from the rear of the bulb. 5-44 4. Remove the headlamp cap. 5.
Page 253: Front Turn Signal, Sidemarker And Parking Lamps
10. Reinstall the headlamp assembly using the three bolts. Front Turn Signal, Sidemarker and Parking Lamps To replace a front turn signal or parking lamp bulb: 1. Open the hood. See Hood Release on page 5-12 for more information. 2. Remove the three bolts to remove the headlamp assembly.
Page 254 4. Turn the front turn signal bulb socket counterclockwise. 5. Pull the front turn signal bulb socket out of the lamp housing. 6. Press the bulb inward and turn it counterclockwise to remove it from the bulb socket. 7. Install the new bulb into the socket by pressing it in and turning it clockwise.
Page 255: Center High-Mounted Stoplamp (Chmsl) (Hatchback)
Center High-Mounted Stoplamp (CHMSL) (Hatchback) To replace a CHMSL bulb on the hatchback: 1. Open the liftgate. See Liftgate (Hatchback) on page 2-10 for more information. 2. Pull down on the lamp assembly while holding the end of the bracket. 3.
Page 256: Taillamps, Turn Signal, Sidemarker, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps To replace a taillamp, turn signal lamp, stoplamp, or back-up bulb: 1. Open the liftgate or trunk. See Liftgate (Hatchback) on page 2-10 or Trunk (Sedan) on page 2-8. Hatchback 5-48 Sedan 2.
Page 257: License Plate Lamp
License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps. 2. Turn and pull the license plate lamp toward you through the opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Page 258: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See “Wiper Blade Check” for more information. Replacement blades come in different types and are removed in different ways. For the proper type, see Maintenance Replacement Parts on page 6-15. 5-50 Here is how to remove and replace the windshield wiper blade:...
Page 259: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. CAUTION: Poorly maintained and improperly used tires are dangerous.
Page 260: Tire Sidewall Labeling
Tire Sidewall Labeling Usefulinformation about a tire is molded into its sidewall. The examples below show a typical passenger car tire and a compact spare tire sidewall. Passenger Car Tire Example 5-52 (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description.
Page 261 (F) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inﬂation - Tire Pressure on page 5-57 and Loading the Vehicle on page 4-16. Compact Spare Tire Example (A) Temporary Use Only The compact...
Page 262: Tire Terminology And Deﬁnitions
Tire Size The following illustration shows an example of a typical passenger car tire size. (A) Passenger (P-Metric) Tire version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Page 263 Aspect Ratio The relationship of a tire’s height to its width. Belt A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
Page 264 Maximum Loaded Vehicle Weight curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-16. Occupant Distribution Designated seating positions.
Page 265: Inﬂation - Tire Pressure
UTQGS (Uniform Tire Quality Grading Standards) A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-66.
Page 266 The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity. For additional information regarding how much weight your vehicle can carry, and an example of the Tire and Loading Information label, see Loading the Vehicle on page 4-16.
Page 267: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer...
Page 268: Tire Pressure Monitor Operation
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Page 269 The tire pressure warning light may come on in cool weather when the vehicle is ﬁrst started, and then turn off as you start to drive. This could be an early indicator that the tire pressures are getting low and need to be inﬂated to the proper pressure.
Page 270: Tire Inspection And Rotation
If the TPMS is not functioning it cannot detect or signal a low tire condition. See your dealer/retailer for service if the TPMS malfunction light and DIC message comes on and stays on. TPMS Sensor Identiﬁcation Codes Each TPMS sensor has a unique identiﬁcation code. Any time you replace one or more of the TPMS sensors, or rotate the vehicle’s tires, the identiﬁcation codes need to be matched to the new tire/wheel position.
Page 271: When It Is Time For New Tires
After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the tire and loading information label. See Loading the Vehicle on page 4-16 for an example of the tire and loading information label and where it is located on your vehicle.
Page 272: Buying New Tires
• The tire has a bump, bulge, or split. • The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage. The rubber in tires degrades over time, even if they are not being used.
Page 273: Different Size Tires And Wheels
CAUTION: If you use bias-ply tires on the vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on the vehicle.
Page 274: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum selection width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the Unites States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 275: Wheel Alignment And Tire Balance
Temperature — A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 276: Tire Chains
If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle.
Page 277: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 278: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6. CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 279: Removing The Spare Tire And Tools
When the vehicle has a ﬂat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire.
Page 280 3. Remove the foam tray. 4. Remove the jack, the jack handle and the wheel wrench from the foam tray. 5-72 5. Turn the retainer counterclockwise and remove it from the compact spare. 6. Remove the compact spare tire. See Compact Spare Tire on page 5-78 for more information.
Page 281: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 5-70. 2. If your vehicle has wheel covers, turn the four plastic caps counterclockwise by hand or by using the wheel wrench.
Page 282 Hatchback 5-74 Sedan 5. Locate the notch in the frame near each wheel which the jack head ﬁts in. 6. Position the jack and raise the jack head until it ﬁts ﬁrmly into the notch in the vehicle’s frame nearest the ﬂat tire.
Page 283 8. Insert the jack handle into the jack and the wheel wrench onto the end of the jack handle. CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
Page 284 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 285 CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 286: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 287: Appearance Care
Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel and other parts of the vehicle. Do not use your compact spare on other vehicles.
Page 288: Fabric/Carpet
Dust may be removed from small buttons and knobs using a small brush with soft bristles. Products that remove odors from the vehicle’s upholstery and clean the vehicle’s glass can be obtained from your dealer/retailer. Do not clean the vehicle using: •...
Page 289: Leather
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness ﬁrst. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Page 290: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak.
Page 291: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-82. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish.
Page 292: Windshield And Wiper Blades
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer ﬂuid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking.
Page 293: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Page 294: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 295: Headlamp Wiring
Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have the headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse.
Page 296: Instrument Panel Fuse Block
Instrument Panel Fuse Block The instrument panel fuse block is located on the end of the instrument panel on the driver side of the vehicle. To access the fuses, open the fuse panel door by pulling the door out. To reinstall the door, ﬁrst insert the rear edge of the fuse panel door, then push the front of the door into the end of the instrument panel to secure it.
Page 297: Engine Compartment Fuse Block
Fuses Usage CIGAR Cigar Lighter Brake Switch, TPMS, Anti-Theft CLUSTER Module DEFOG Power Mirror Unit, A/C Switch MIRROR RR DEFOG Rear Defog DOOR LOCK Door Lock NA DRL NA DRL Circuit MIRROR/ Mirror Control Switch, Room Lamp, SUNROOF A/C Switch Engine Room Fuse Block, TCM, EMS 1 VSS, Fuel Pump...
Page 298 Fuses FAN HI Cooling Fan HI Relay ABS-1 EBCM ABS-2 EBCM 5-90 Usage SJB BATT ACC/IG1 IG2/ST Fuses Usage Instrument Panel Fuse Block IGN1 Relay IGN2 Relay, Starter Relay...
Page 299 Fuses Usage ACC/RAP Instrument Panel Fuse Block P/WINDOW-2 Power Window Switch Power Window Switch WINDOW-1 FAN LOW Cooling Fan LOW Relay A/CON A/C Compressor Relay Tail Lamp (LH), Side Marker (LH), PKLP LH Turn Signal & Parking Lamp (LH), License Lamp Tail Lamp (RH), Side Marker (RH), PKLP RH Turn Signal &...
Page 300 Relays F/PUMP Fuel Pump RELAY STARTER Starter RELAY PARK LAMP Park Lamp RELAY FRONT FOG Fog Lamp RELAY HDLP HIGH Head Lamp High RELAY HDLP LOW Head Lamp Low RELAY 5-92 Usage Relays FAN HIGH RELAY FAN LOW RELAY A/CON RELAY Air Conditioner ENGINE MAIN RELAY ACC/RAP...
Page 301: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information. Application Air Conditioning Refrigerant R134a Cooling System Engine Oil with Filter Fuel Tank Transmission, Automatic Transmission, Manual Wheel Nut Torque All capacities are approximate.
Page 302 ✍ NOTES 5-94...
Page 303 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-8 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-10 At Least Once a Month ...6-10 At Least Once a Year ...6-11 Recommended Fluids and Lubricants ...6-13...
Page 304: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 305 This schedule is for vehicles that: • carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Loading the Vehicle on page 4-16. • are driven on reasonable road surfaces within legal driving limits. • use the recommended fuel.
Page 306: Scheduled Maintenance
Scheduled Maintenance When the change engine oil light displays, service is required for the vehicle. Have the vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 307 Change engine oil and ﬁlter. See Engine Oil on page 5-16. Reset oil life system. See Engine Oil Life System on page 5-18. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-19.
Page 308: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 309 Additional Required Services (cont’d) Service and Miles (Kilometers) Inspect EVAP canister and vapor lines. Replace EVAP vent solenoid valve. An Emission Control Service. See footnote †. Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i).
Page 310: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 311: Owner Checks And Services
(h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 312: Engine Oil Level Check
At Each Fuel Fill It is important to perform these underhood checks at each fuel ﬁll. Engine Oil Level Check Notice: It is important to check the engine oil regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by the vehicle warranty.
Page 313: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Page 314: Ignition Transmission Lock Check
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • For automatic transmission vehicles, the ignition should turn to LOCK/OFF only when the shift lever is in P (Park). •...
Page 315: Recommended Fluids And Lubricants
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal.
Page 316 Usage Fluid/Lubricant Windshield ® Washer Solvent Optikleen Washer Solvent. ® Power Steering DEXRON -VI Automatic System Transmission Fluid. Use only T-IV Automatic Automatic Transmission Fluid Transmission (GM Part No. U.S. 88900925, in Canada 22689186). Manual Transmission Fluid Manual (GM Part No. U.S. 89021806, Transmission in Canada 89021807).
Page 317: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter Passenger Compartment Air Filter Spark Plugs Wiper Blades - Hatchback Driver Side Passenger Side Rear Wiper Blades - Sedan Driver Side...
Page 318: Engine Drive Belt Routing
Engine Drive Belt Routing 6-16...
Page 319: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 320 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 321 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-19...
Page 322 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-20...
Page 323: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-5 Customer Assistance for Text Telephone (TTY) Users ...7-6 Customer Assistance Offices ...7-6 GM Mobility Reimbursement Program ...7-7 Roadside Assistance Program ...7-7 Scheduling Service Appointments ...7-11 Courtesy Transportation ...7-11 Collision Damage Repair ...7-13 Customer Assistance Information...
Page 324: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 325 STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you can ﬁle with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
Page 326 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Page 327: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Chevrolet dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 328: Customer Assistance For Text Telephone (Tty) Users
Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 329: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000 Long Distance: 011-52-53 29 0 800 GM Mobility Reimbursement...
Page 330: Calling For Assistance
Roadside Assistance is not a part of the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 331: Services Provided
• Emergency Tow From a Public Road or Highway: Tow to the nearest Chevrolet dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow.
Page 332 Services Speciﬁc to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. • Lock-Out Service: Vehicle registration is required. • Trip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route.
Page 333: Scheduling Service Appointments
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience. If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related.
Page 334: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
Page 335: Collision Damage Repair
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualiﬁed technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle’s resale value, and safety performance can be compromised in subsequent collisions.
Page 336: Insuring Your Vehicle
Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are signiﬁcant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
Page 337 • If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver’s name, the service’s name, and the phone number. • Remove any valuables from your vehicle before it is towed away.
Page 338: Reporting Safety Defects
Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts.
Page 339: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or...
Page 340: Vehicle Data Recording And Privacy
Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Page 341: Event Data Recorders
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
Page 342: Onstar
® OnStar If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use. Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information.
Page 343 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlets ... 3-16 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-74 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-86 Air Cleaner/Filter, Engine ... 5-19 Air Conditioning ... 3-18 Airbag Passenger Status Indicator ... 3-27 Readiness Light ...
Page 344 Audio System (cont.) Fixed Mast Antenna ... 3-58 Radio Reception ... 3-58 Radio with CD ... 3-46 Automatic Transmission Fluid ... 5-21 Operation ... 2-22 Backglass Antenna ... 3-59 Battery ... 5-37 Inadvertent Power Saver ... 3-16 Brake Emergencies ... 4-6 Brake Fluid ...
Page 345 Chemical Paint Spotting ... 5-85 Child Restraints Child Restraint Systems ... 1-41 Infants and Young Children ... 1-38 Lower Anchors and Tethers for Children ... 1-46 Older Children ... 1-34 Securing a Child Restraint in a Rear Seat Position ... 1-53 Securing a Child Restraint in the Right Front Seat Position ...
Page 346 Daytime Running Lamps Indicator Light ... 3-36 Defensive Driving ... 4-2 Disc, MP3 ... 3-54 Doing Your Own Service Work ... 5-4 Dome Lamp ... 3-16 Door Ajar Light ... 3-36 Central Door Unlocking System ... 2-7 Door Ajar Reminder ... 2-7 Locks ...
Page 347 Filter Engine Air Cleaner ... 5-19 Finish Damage ... 5-85 Fixed Mast Antenna ... 3-58 Flashers, Hazard Warning ... 3-6 Flash-to-Pass ... 3-8 Flat Tire ... 5-69 Flat Tire, Changing ... 5-70 Flat Tire, Storing ... 5-78 Fluid Automatic Transmission ... 5-21 Power Steering ...
Page 348 Headlamps ... 5-44 Bulb Replacement ... 5-43 Daytime Running Lamp ... 3-14 Exterior Lamps ... 3-13 Flash-to-Pass ... 3-8 Front Turn Signal, Sidemarker and Parking Lamps ... 5-45 Halogen Bulbs ... 5-43 High/Low Beam Changer ... 3-8 Heater ... 3-18 Engine ...
Page 349 Liftgate Carbon Monoxide ... 2-10 Light Airbag Readiness ... 3-26 Antilock Brake System (ABS) Warning ... 3-30 Brake System Warning ... 3-28 Change Engine Oil ... 3-35 Charging System ... 3-28 Cruise Control ... 3-36 Daytime Running Lamps Indicator ... 3-36 Door Ajar ...
Page 350 Mirrors Manual Rearview Mirror ... 2-34 Outside Convex Mirror ... 2-35 Outside Heated Mirrors ... 2-35 Outside Manual Mirrors ... 2-34 Outside Power Mirrors ... 2-35 MP3 ... 3-54 MyGMLink.com ... 7-5 Navigation System, Privacy ... 7-20 New Vehicle Break-In ... 2-18 Odometer ...
Page 351 Power Electrical System ... 5-87 Inadvertent Battery Saver ... 3-16 Steering Fluid ... 5-32 Windows ... 2-13 Privacy ... 7-18 Event Data Recorders ... 7-19 Navigation System ... 7-20 OnStar ... 7-20 Radio Frequency Identiﬁcation ... 7-20 Radio Frequency Identiﬁcation (RFID), Privacy ... 7-20 Radios AM-FM Radio ...
Page 352 Safety Belts (cont.) Safety Belt Extender ... 1-34 Safety Belt Use During Pregnancy ... 1-33 Safety Belts Are for Everyone ... 1-16 Safety Warnings and Symbols ... iii Scheduled Maintenance ... 6-4 Seats Driver Seat Height Adjuster ... 1-5 Head Restraints ... 1-2 Manual Lumbar ...
Page 353 Tachometer ... 3-25 Taillamps Turn Signal, Sidemarker, Stoplamps, and Back-Up Lamps ... 5-48 Theft-Deterrent Systems ... 2-14 Content Theft-Deterrent ... 2-16 Immobilizer ... 2-14 Immobilizer Operation ... 2-15 Tilt Wheel ... 3-6 Time ... 3-17 Tire Pressure Light ... 3-31 Tires ...
Page 354 Uniform Tire Quality Grading ... 5-66 Up-Shift Light ... 3-28 Vehicle Control ... 4-3 Loading ... 4-16 Parking Your ... 2-31 Running While Parked ... 2-33 Symbols ... iii Vehicle Data Recording and Privacy ... 7-18 Vehicle Identiﬁcation Number (VIN) ... 5-86 Service Parts Identiﬁcation Label ...

Chevrolet 2009 Aveo Owner's Manual

Section 1 Seats and Restraint System

Head Restraints

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Trip Computer

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2009 Aveo

Summary of Contents for Chevrolet 2009 Aveo